speco technologies SPIP200M IP Audio Encoder
Product Information
Specifications
- Protocol: SIP, ONVIF, HTTP, IPv4, DHCP, RTSP, RTP, RTCP, TCP, UDP, ARP, FTP, TFTP, NFS, NTP
- Codec: OPUS 48 kHz, MP3 44.1 kHz, G.722 ADPCM 16 kHz, G.711 PCMU 8 kHz, G.711 PCMA 8 kHz
- Network Interface: RJ45, 10BASE-T/100BASE-TX
- Power: PoE or DC 12V/24V
- Rated Power: 15W
- Interface: 6 Pin Audio Interface (1* MIC input, 1* Headset output, 1* Speaker output), 4 Pin IO Interface (2* IO Alarm input), 4 Pin Alarm Out Interface (1* Relay output, 1* IO output)
- Function: Compatible with VoIP devices and ONVIF VMS, supports two-way communication, pre-recorded messages, schedule play, GPIO in, HTTP control
- Material: Metal
- Color: Black
- Weight: 250g
Product Usage Instructions
Installation
- Connect the IP Audio Encoder to a power source using PoE or DC 12V/24V.
- Connect the audio interfaces (MIC input, Headset output, Speaker output) and IO interfaces as needed.
Configuration
- Access the device using a web browser and configure the network settings.
- Set up SIP and ONVIF protocols for communication.
- Configure pre-recorded messages and schedules as required.
Operation
- Use the device for two-way audio communication with compatible devices.
- Control the device via HTTP commands for functions like GPIO in and schedule play.
Specification
|
Protocol |
SIP, ONVIF, HTTP, IPv4, DHCP, RTSP, RTP, RTCP, TCP, UDP, ARP, FTP, TFTP, NFS,
NTP |
|
Codec |
OPUS 48 kHz, MP3 44.1 kHz, G.722 ADPCM 16 kHz, G.711 PCMU 8 kHz, G.711 PCMA 8 kHz |
| Network Interface |
RJ45, 10BASE-T/100BASE-TX |
| Power | PoE or DC 12V/24V |
| Rated Power | 15W |
|
Interface |
6 Pin Audio Interface： 1* MIC input, 1* Headset output, 1* Speaker output 4 Pin IO Interface：2* IO Alarm input
4 Pin Alarm Out Interface: 1* Relay output，1* IO output |
|
Function |
Compatible with VoIP devices and ONVIF VMS, supports two-way communication, pre-recorded messages, schedule play, GPIO in, HTTP control |
| Material | Metal |
| Color | Black |
| Weight | 250g |
Refer to the product page for the User Manual and full product details at specotech.com
Features
- Two-way audio communication.
- SIP & ONVIF protocol compatibility.
- PoE eliminates the need for local power supply.
- 48K OPUS Audio Codec enables excellent sound quality.
- Support pre-recorded messages, schedule, HTTP, alarm in/out.
Interface
| Label | Description | Label | Description |
| ① | IO Input Interface | ② | IO Input Interface |
| ③ | Relay NO COM Interface | ④ | IO Output Interface |
| ⑤ | Microphone Interface | ⑥ | Headset Interface |
| ⑦ | Speaker Interface | ⑧ | PoE Interface |
| ⑨ | Volume Control Key | ⑩ | Reset Interface |
| ⑪ | Audio LED | ⑫ | Power LED |
| ⑬ | Power Input Interface |
FAQ’s
Q: Can the SPIP200M IP Audio Encoder be powered using PoE?
A: Yes, the SPIP200M IP Audio Encoder can be powered using PoE or DC 12V/24V.
Q: What audio codecs are supported by the device?
A: The device supports OPUS 48 kHz, MP3 44.1 kHz, G.722 ADPCM 16 kHz, G.711 PCMU 8 kHz, and G.711 PCMA 8 kHz codecs.
Q: How can I configure pre-recorded messages on the device?
A: You can configure pre-recorded messages through the device’s web interface by accessing the schedule settings.
Documents / Resources
 |
speco technologies SPIP200M IP Audio Encoder [pdf] User Guide SPIP200M, IPC-615, 615POE, SPIP200M IP Audio Encoder, SPIP200M, IP Audio Encoder, Audio Encoder |
