IB8A04832CVXX CODESYS Light Plus Building Contactor
“
Specifications:
- Input Current: Less than 200 mA
- Output: 4 NO (SPST)
- Max Switching Current: 10 A, 250 V AC1 / 4 A, 24 V DC1
- Power Consumption: 0.5 Nm
- Motor Power: 1/2 HP 240 V AC / 1/4 HP 120 V AC
- Digital/Analog Inputs: 8 (0-10 V)
- Processor: STM32H747XI Dual ARM Cortex M7/M4 IC
- Communication Interfaces: USB Type C, 10/100 Ethernet, RS485,
Wi-Fi + BLE - Mounting: EN 60715 rail mounting
- Environmental Conditions: Extended Humidity 5-95 RH%, Altitude
2000 m, IP20
Product Usage Instructions:
Installation:
- Ensure the device is mounted on an EN 60715 rail securely.
- Connect the appropriate power source based on the motor power
requirements. - Connect any required digital/analog inputs to the designated
ports. - Establish communication interfaces such as USB Type C,
Ethernet, RS485, Wi-Fi, or BLE as needed.
Operation:
- Power on the device using the specified power source.
- Monitor the device status using the LED indicators.
- Utilize the digital/analog inputs for controlling the device
based on the application requirements. - Ensure proper communication via the available interfaces for
data exchange.
Maintenance:
- Regularly check for any loose connections or signs of wear and
tear. - Clean the device and its surroundings to prevent dust
accumulation. - Update firmware or software as recommended by the manufacturer
for optimal performance.
FAQ:
Q: What should I do if the device shows an error code?
A: Refer to the user manual for error code explanations and
troubleshooting steps. If the issue persists, contact customer
support.
Q: Can I use this product in all EU member states?
A: Yes, this product is compliant with EU regulations and can be
used in all EU member states.
Q: How do I reset the device to factory settings?
A: Locate the RESET button on the device and follow the
instructions in the manual to perform a factory reset.
“`
8A.04.9.024.832C
UN (12…24) V DC + 15% Class 2 source
I < 200 mA
1
0.5 Nm
OUTPUT
4 NO (SPST)
10 A, 250 V AC1
4 A, 24 V DC1
1M~
1/2 HP 240 V AC 1/4 HP 120 V AC
8 digital/ analog (0…10 V) INPUT
9mm
1×2.5 / 2×1.5 mm2 1×14 / 2×16 AWG
STM32H747XI Dual ARM R Cortex R M7/ M4 IC:
9mm
1x ARM R Cortex R -M7 core up to 480 MHz
1x ARM R Cortex R -M4 core up to 240 MHz
2
1×2.5 / 2×1 mm2
USB Type C
1×14 / 2×16 AWG
10/100 Ethernet
RS485
8A.04
Wi-Fi + BLE
Secure element integrated
2a
(20…+50)°C
Open type, EN 60715 rail mounting Environmental Conditions: Extended
Humidity 5-95 RH% Altitude 2000 m IP20
LISTED
E528578
FCC ID: 2A97G-8A001 (Only for mod: 8A…832C)
Utility Model – IB8A04832CVXX – 01/25 – Finder S.p.A. con unico socio – 10040 ALMESE (TO) – ITALY
FCC and RED CAUTIONS (MODEL 8A.04.9.024.832C)
FCC
Any Changes or modifications not expressly approved by the party responsible
3a
for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
FCC RF Radiation Exposure Statement:
3c
– this Transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter
3d
– this equipment complies with RF radiation exposure limits set forth for an
uncontrolled environment
– this equipment should be installed and operated with minimum distance
20 cm between the radiator& your body 3e
NOTE
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
3f
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference
at his own expense.
RED
The product is in compliance with essential requirements and other relevant
provisions of Directive 2014/53/EU.
3k
This product is allowed to be used in all EU member states.
Frequency bands
Maximum output power (EIRP)
2412 – 2472 MHz (2.4G WiFi) 2402 – 2480 MHz (BLE) 2402 – 2480 MHz (EDR)
5,42 dBm 2,41 dBm 6,27 dBm
3
3b 3j 3i
3h 3g
3m
8A.04.9.024.8320C Codesys
1
2
2a Modbus RTU 3n
3
3a 12…24 V DC 3b I1….I8 / (0…10 V)
IDE 3c RESET ( ) 3d 3e LED 1…4 3f 1…4, (SPST) 10 A 250 V AC 3g 3h LED Ethernet (ETH) 3i 060.48 3j MODBUS RS485 3k USB Type-C 3m Ethernet 3n
opta.findernet.com Finder OPTA Type 8A.04 , CODESYS Finder, opta.findernet.com. Finder OPTA Type 8A.04 , USB-C. Finder OPTA Type 8A.04, LED.
, .
Documents / Resources
 |
finder IB8A04832CVXX CODESYS Light Plus Building Contactor [pdf] Instructions IB8A04832CVXX, IB8A04832CVXX CODESYS Light Plus Building Contactor, CODESYS Light Plus Building Contactor, Light Plus Building Contactor, Building Contactor |