SW102 DISPLAY
User Guide 
SW102 Display
SW102 Display User Guide
Product Details
Product Name
Intelligent OLED display, model: SW102
Firmware: CYCMOTOR LTD specific firmware
Features
- Minimalist design and process
- High brightness, high contrast 1.3-inch monochromatic OLED screen
- Excellent outdoor design with IP65 waterproof rating
Dimensions & Materials
Materials
Product shell – ABS + PC plastic
Transparent window – 2.5D Tempered glass
Dimensions
L 23mm x W 40mm x H 63mm
Electrical Specifications
- Power supply: DC 36V / 48V / 52V
- Rated current: 12mA
- Shutdown leakage current: <1uA
- Screen specification: 1/3” OLED (64*128 dots)
- Communication method: UART (default)
- Operating temperature: -20°C ~ 80°C
- Storage temperature: -30°C ~ 80°C
- Waterproof level: IP65
Quick Start Guide
After unboxing and installing your CYC motor system, there are two main things you need to set up.
- Change your Battery No. setting according to your rated voltage.
a. Within 15 seconds of turning on your display, long press the MENU button to enter the settings functions. Press UP/DOWN to navigate the settings page & MENU to select.
- Change your Wheel setting according to your bike’s wheel size.
- Now you can set things up like your temperature and speed unit as well as your brightness level.
Functionalities
Power On/Off
Press and hold the POWER button for 2 seconds to turn the display on/off. The display will automatically shut down when there is no operation for a period of time.
Navigation
- POWER
- MENU
- UP
- DOWN
The MENU button is used to go into your settings page & clear data page. It is also used to enter and select a setting or function & finally, it’s also used to switch between the various main dashboard information. 
Switch Dashboard
Switch the main dashboard to display different information by pressing the MENU button. 
Assist Level Operating
Press the UP/DOWN button to change the assist level between level 1, 2, and 3. Please note that “OFF” means no motor assistance will be given. 
Long press the MENU button within 15 seconds of switching on the display to enter the “Settings” page. Note that once the system has been activated for longer than 15 seconds, you will need to restart the motor system to enter the settings menu.
Clean Trip Data
In certain circumstances, an error code may appear on your display. Contact us for assistance.
| Error Code on SW102 Display | Error Code on App |
| 1 | Controller Over Voltage |
| 2 | Controller Under Voltage |
| 4 | Controller Internal Error 1 |
| 5 | Controller Over Temperature |
| 6 | Motor Over Temperature |
| 9 | Controller Internal Error 10 |
| 10 | Controller Internal Error 2 |
| 14 | Controller Internal Error 3 |
| 15 | Controller Internal Error 4 |
| 16 | Controller Internal Error 5 |
| 17 | Controller Internal Error 6 |
| 18 | Controller Internal Error 7 |
| 23 | Controller Internal Error 8 |
| 24 | Controller Internal Error 9 |
| 26 | Hall Sensor Error |
| 28 | Throttle Error |
| 29 | Speed Sensor Error |
Installation
Adjust it in place and tighten the screw accordingly.
Note: Damage caused by excessive torque is not covered by warranty.
- Red Wire: Anode (36V to 72V)
- Black Wire: GND
- Yellow Wire: TxD (display -> controller)
- Green Wire: RxD (controller -> display)
- Blue wire: Power cord to the controller
CE / IP65 (waterproof) / ROHS
Be sure to contact us if further assistance is needed. Thank you!
Documents / Resources
 |
CYC MOTOR SW102 Intelligent OLED Display [pdf] User Guide SW102 Intelligent OLED Display, SW102, Intelligent OLED Display, OLED Display, Display |
 |
CYC MOTOR SW102 Intelligent OLED Display [pdf] User Guide SW102 Intelligent OLED Display, SW102, Intelligent OLED Display, OLED Display, Display |
 |
CYC MOTOR SW102 Intelligent OLED Display [pdf] User Guide SW102 Intelligent OLED Display, SW102, Intelligent OLED Display, OLED Display, Display |
 |
CYC Motor SW102 Intelligent OLED Display [pdf] User Guide SW102 Intelligent OLED Display, SW102, Intelligent OLED Display, OLED Display, Display |