AGT V Video Intercom Handset
Product Information
The AGT V + LITHOS Kit is a complete system that includes the
AGT V internal video receiver and the LITHOS installation manual.
The AGT V is a versatile device that functions as an internal video
receiver. It is equipped with terminals and jumpers for various
functions, including the closing resistance (CL.RES) and
master/slave selector (M/S). The AGT V has the following technical
data:
- Operating Voltage: 15 to 20 volts
- Current Consumption: 175 mA
- Dimensions: 3 inches
Product Usage Instructions
To install and use the AGT V + LITHOS Kit, follow these
steps:
- Ensure you have all the components included in the kit, which
are:- AGT V internal video receiver
- LITHOS installation manual
- Refer to the LITHOS installation manual for detailed
instructions on how to properly install and set up the AGT V. - Connect the AGT V to a power source with an operating voltage
between 15 and 20 volts. - Make sure to connect the appropriate terminals and jumpers
based on your desired configuration. The closing resistance
(CL.RES) and master/slave selector (M/S) are available for
different functions. - Refer to the technical data provided for further information on
the AGT V’s specifications.
Please consult the LITHOS installation manual for any additional
information or troubleshooting guidelines.
KIT AGT V + LITHOS
FA01429-EN
AGT V
M1 M2 +
VAS/101
LITHOS
INSTALLATION MANUAL
AGTLVKIT
EN English
Page 2 – Manual FA01429-EN – 07/2020 – © CAME S.p.A. -The contents of this manual may be changed, at any time, and without notice. – Translation of the original instructions
CONTENTS OF THE KIT
AGT V
M1 M2 +
VAS/101
LITHOS
General precautions · Read the instructions carefully before beginning the installation and carry out the procedures as specified by the manufacturer. · The product must be installed, programmed, commissioned and serviced by qualified technicians, correctly trained with regard to respecting the regulations in force, including implementing accident-prevention measures. · Before carrying out any cleaning or maintenance operation, disconnect the power supply. · The equipment must only be used for the purpose for which it was designed. · The manufacturer declines all liability for any damage as a result of improper, incorrect or unreasonable use.
Page 3 – Manual FA01429-EN – 07/2020 – © CAME S.p.A. -The contents of this manual may be changed, at any time, and without notice. – Translation of the original instructions
AGT V
Description Internal video receiver.
Function of terminals and jumpers
Terminal board M1 B BUS-line input Landing call + AL Alarm input
Closing resistance (CL.RES) Master/slave selector (M/S)
Technical data
Type Power supply from BUS line (VDC) Maximum consumption (mA) Consumption in stand-by mode (mA) Single LED consumption (mA) Operating temperature (°C) IP Rating Video standard LCD TFT display (inches)
AGT V 15 to 20
175 <1 1 +5 to +40 IP 30 PAL/NTSC 5
AL +
B CL.RES M/S
M1
XDV/304
CL.RES
CL.RES
CL.RES
Fam. Rossi
M/S MASTER
M/S
SLAVE
Page 4 – Manual FA01429-EN – 07/2020 – © CAME S.p.A. -The contents of this manual may be changed, at any time, and without notice. – Translation of the original instructions
1 2
Installation
· Unhook the device from the metal support by pressing the plastic tab and sliding the device smoothly off the support . · Fix the wall support to the round Ø 60 mm recessed box , to the rectangular box 503 , or to the Ophera (PHI) recessed box , with the “TOP” arrow pointing upwards. · Avoid overtightening the screws. · Use screws and anchors to make the support more stable. · The box must be installed at a suitable height for the user. · Once the connections have been made, attach the video terminal to the metal support . · To unfasten the unit from the metal support, press the plastic tab and lift the terminal .
System limits 4 monitors can be switched on simultaneously only in one- or two- family systems with entry panel X1+VA/01.
XDV/304
Lb VA/01
N° Master
N° Slave
La
VCM/1D UTP CAT5
No. Master No. Slave
4321321 4567067
L1
L2
L3
Page 5 – Manual FA01429-EN – 07/2020 – © CAME S.p.A. -The contents of this manual may be changed, at any time, and without notice. – Translation of the original instructions
MTM
MTM
MTM
VCM/1D VCM/2D UTP/CAT 5
La+Lb L1, L2, L3 L1+L2+ L3 La + Lb + L1(L2, L3) La + Lb + L1 + L2 + L3
100 m
60 m
100 m
300 m
150 m 600 m
2 x 2.5 mm2
N° Master
N° Slave
XDV/304 La
Lb
No. Master No. Slave
VCM/1D UTP CAT5
3211 0373
Lithos
VAS/101 Lc
La+Lb Lc La+Lb+Lc
VCM/1D VCM/2D
100 m
UTP/CAT 5 100 m
100 m
2x1mm2
25 m
2 x 2.5 mm2
60 m
Page 6 – Manual FA01429-EN – 07/2020 – © CAME S.p.A. -The contents of this manual may be changed, at any time, and without notice. – Translation of the original instructions
3sec … beep!
Configuring melodies Perform each of the following programming-steps, in succession:
1-Enter programming mode. Press and hold the button for 3 seconds. A short buzzing sound and a red flashing LED confirm that you have entered programming mode . 2-Programming the melody associated with the call from the entry panel. To listen to the melodies in sequence, press . To select the melody and exit the programming mode, press . To select the melody and continue programming, press . 3- Programming the melody associated with a call from the landing. To listen to the melodies in sequence, press . To select the melody and exit the programming mode, press . To select the melody and continue programming, press . 4-Programming the number of rings per call. Press as many times as the number of rings you want (from 1 to 12 rings) . Three seconds after the key was last pressed, the selected call is played back with the chosen number of rings.
To exit programming mode, press .
To program a call, please see the entry panel manuals.
VAS/101
Installation
The power supply must always be installed horizontally. · The device can be installed on DIN rails (EN 50022) on a suitable switchboard. · See figure for dimensions. NOTE. Ensure there is correct ventilation if the power supply is installed in a metal case.
Terminal board M1 ~
Network ~
Terminal board M2
+
Power supply 18 V DC (*)
(*) The device is electronically protected against overloads and short circuits.
M1 M2 +
Page 7 – Manual FA01429-EN – 07/2020 – © CAME S.p.A. -The contents of this manual may be changed, at any time, and without notice. – Translation of the original instructions 106 45
Technical data
Type
VAS-101
Power supply
230 VAC 50-60 Hz
Max. absorbed current
200
A
(mA AC)
Dissipated power
10 W max
Rated power
18 VDC 1 A-0.5 A 1’/3′
Size
4 DIN
70
43,5
Storage temperature
-25°C + 70°C
7,5 57
Operating temperature
0°C +35°C
IP rating
IP 30
LVC/01
500 mm 800 mm 1550 – 1600 mm
Page 8 – Manual FA01429-EN – 07/2020 – © CAME S.p.A. -The contents of this manual may be changed, at any time, and without notice. – Translation of the original instructions
Wall-mounted installation
Use a hex key to unscrew the screws in the front plate and remove it (figure ).
Fix the plugs provided and screw in the entry panel (figure ) at the desired height, bearing in mind the position of the video camera lens (figure ). Thread the pipe with the system conductors as shown in figure .
1080 mm
94°
43,5 mm 77°
163,5 mm
500 mm
Pull out the plastic terminal cover and make the connections
(figure ).
Once the connections have been made, reinsert the terminal
covers.
For information on fitting accessories, please see the “Button
modules assembly” section.
Program and adjust the entry panel as described in the “Pro-
gramming” section. Fit the front plate (figure ).
Recessed installation
First thread the pipe with the system conductors through one of the break points (figure , point ). Then wall in the recessed box at the desired height, bearing in mind the position of the video camera lens (figure ). When installing the recessed box, avoid any deformations by using the spacer provided (figure , point . Use a hex key to unscrew the screws in the entry-panel front plate and remove it (figure ). Thread the connection cables through the hole (figure ) and
fix the entry panel to the frame as shown in figure . Pull out
the plastic terminal cover and make the connections (figure ).
Once the connections have been made, reinsert the terminal
covers.
For information on fitting accessories, please see the “Button
B
modules assembly” section.
Program and adjust the entry panel as described in the “Pro-
gramming” section.
Fit the front plate (figure ).
A
Page 9 – Manual FA01429-EN – 07/2020 – © CAME S.p.A. -The contents of this manual may be changed, at any time, and without notice. – Translation of the original instructions
DPS LSI
LTP LCI
Accessories – Single button DPS , – Wall cover LTP , – Recessed box LSI , – Recessed frame LCI .
Assembling the modules Insert the button module as shown in figure , making sure it is the right way up (figure ). Remove the glass and write the names of the users as shown in figure , paying particular attention to which way round the glass is inserted (figure ). Name cards: Size
PROG
Page 10 – Manual FA01429-EN – 07/2020 – © CAME S.p.A. -The contents of this manual may be changed, at any time, and without notice. – Translation of the original instructions
1 2
53x13x0.3 mm
Function of terminals
M1 M2 +
M1 BOUT
+
NO C
B B
9/6
53x33x0.3 mm
PROG M2
SW3
Page 11 – Manual FA01429-EN – 07/2020 – © CAME S.p.A. -The contents of this manual may be changed, at any time, and without notice. – Translation of the original instructions
Terminal board M1 BOUT Busbar
+
16-18 VDC power supply
Terminal board M2 Earth Door release button (NA)
Electric lock 12 V 1 A max
Technical data
Type Entry panel Power supply Power draw Size Storage temperature Operating temperature IP Rating Video camera Video standard Resolution Minimum lighting
LVC/01
16-18 VDC 250 mA (100 mA stand-by) 99x207x30 mm -25°C +70°C -15°C +50°C IP 54
PAL/NTSC 680×512 pixels 1 LUX
LED functions and adjustment speaker audio microphone audio solenoid lock 1-10 s. (default 1 s)
Off On Slow flash
Quick flash
LED symbols
M1 BOUT
M1 BOUT
PROG
RESET
PROG M2
M2 SW3
PROG
PROG
>3” <6”
SW3
Programming
Programming for the first time Entering programming mode. Press and hold the PROG key for at least 3 s, then release it (within 6 seconds) as soon as the PROG LED lights up and the button backlighting flashes as illustrated in figure . If the PROG LED does not light up, there has been a malfunction. Check the connections and return to programming mode.
P
RESET
PROG
M2
SW3
ROG
PROG
PROG
Page 12 – Manual FA01429-EN – 07/2020 – © CAME S.p.A. -The contents of this manual may be changed, at any time, and without notice. – Translation of the original instructions
M1
”
M1
PROG
PROG
Programming type of keys. Press and hold the first key on the
entry panel in the position shown /A until the LED backlighting stops flashing and remains on .
M1 BOUT
PROG
RESET
PROG
M2
SW3
ROG
PROG
P
Programming the call keys. Lift the receiver handset that you want to program (where present), then press the door lock release button and AUX2 button . On the entry panel, press the call key to be associated with the receiver . A beep will confirm that the setting has been stored.
Reposition the handset where applicable and repeat the same operations for all the other receivers.
M1 BOUT
Exiting programming.
Briefly press the PROG key . The PROG LED will switch off. NOTE. If no action is performed, the procedure will end automat-
ically after 30 minutes.
PROG
RESET
PROG M2
M2 SW3
PROG
PROG
<1”
SW3
beep
Page 13 – Manual FA01429-EN – 07/2020 – © CAME S.p.A. -The contents of this manual may be changed, at any time, and without notice. – Translation of the original instructions
M1
M1 BOUT
PROG
RESET
PROG M2
M2 SW3
PROG
P>RO3G” <6”
SW3
Reprogramming procedure
Entering programming mode. Press and hold the PROG key
for at least 3 s, then release it (within 6 seconds) as soon as the
PROG LED flashes and the button backlighting lights up as illustrated in figure . If the PROG LED does not light up, there has been a malfunction.
Check the connections and return to programming mode.
P
RESET
PROG
PROG
M2
SW3
ROG
PROG
Programming the call keys. Lift the receiver handset that you
want to program (where present) , then press the door lock release button and AUX2 button .
beep
On the entry panel, press the call key to be associated with the receiver . A beep will confirm that the setting has been stored. Reposition the handset where applicable and repeat the same operations for all the other receivers.
M1 BOUT
PROG
RESET
PROG M2
M2 SW3
PROG
P<RO1G”
SW3
Exiting programming. Press the PROG key briefly . The PROG LED will switch off.
NOTE. If no action is performed, the procedure will end automat-
ically after 30 minutes.
PROG
Page 14 – Manual FA01429-EN – 07/2020 – © CAME S.p.A. -The contents of this manual may be changed, at any time, and without notice. – Translation of the original instructions
M1 BOUT
M1 BOUT
M1 BOUT
PROG
RESET
PROG
RESET
PROG
PROG
M2
SW3
ROG
>3” PR<OG6”
Programming type of keys. When “Programming call keys”,
press and hold the PROG key for at least 3 seconds, then release it (within 6 seconds) as soon as the PROG LED lights up
and the key backlighting flashes as shown in figure , entering the “Programming type of keys” procedure.
PROG
M2
SW3
ROG
PROG
P
M1 BOUT
Press and hold the first key on the entry panel in the position
shown until the LED backlighting stops flashing and remains on . To exit programming once complete, press the PROG key briefly
. The PROG LED will switch off. If no action is performed, the procedure will end automatically
after 30 minutes.
Page 15 – Manual FA01429-EN – 07/2020 – © CAME S.p.A. -The contents of this manual may be changed, at any time, and without notice. – Translation of the original instructions
This product complies with current applicable reference standards. DISPOSAL – Dispose of the packaging and the device at the end of its life cycle responsibly, in compliance with the laws in force in the country in which the product is used. The recyclable components are marked with a symbol and the material ID marker. THE DATA AND INFORMATION IN THIS MANUAL MAY BE CHANGED AT ANY TIME AND WITHOUT NOTICE. THE MEASUREMENTS, UNLESS OTHERWISE STATED, ARE IN MILLIMETRES.
CAME S.p.A.
Via Martiri Della Libertà, 15 31030 Dosson di Casier – Treviso – Italy tel. (+39) 0422 4940 – fax. (+39) 0422 4941
Page 16 – Manual FA01429-EN – 07/2020 – © CAME S.p.A. – The contents of this manual may be changed, at any time, and without notice. – Translation of the original instructions
KIT AGT V + LITHOS
FA01429-RU
AGT V
M1 M2 +
VAS/101
LITHOS
AGTLVKIT
RU P
. 2 – FA01429-RU – 067/2020 – © CAME S.p.A. – . –
AGT V
M1 M2 +
VAS/101
LITHOS
· , , -. · , , , . · . · . · – , , .
.. 33 — FFAA0011442299–RRUU — 076//22002200–©©CCAAMMEESS..pp..AA..–..–
AGT V
.
M1 B + AL
(CL.RES) master/slave (M/S)
( . ) . () () () (°C) (IP) – TFT ( )
AGT V
15 ÷ 20
175 <1 1 +5 ÷ +40 IP 30 PAL/NTSC 5
AL +
B CL.RES M/S
M1
XDV/304
CL.RES
CL.RES
CL.RES
Fam. Rossi
M/S MASTER
M/S
SLAVE
. 4 – FA01429-RU – 067/2020 – © CAME S.p.A. – . –
1 2
· , –
. · Ø 60 , 503 Ophera (PHI) , TOP («»). · . · .
· .
· , . · , –
.
.. 55 — FFAA0011442299–RRUU — 076//22002200–©©CCAAMMEESS..pp..AA..–..–
4 / X1+VA/01.
XDV/304
Lb VA/01
N° Master
N° Slave
La
VCM/1D UTP CAT5
Master () N° Slave ()
4321321 4567067
L1
L2
L3
MTM
MTM
MTM
La+Lb L1, L2, L3 L1+L2+ L3 La + Lb + L1(L2, L3) La + Lb + L1 + L2 + L3
VCM/1D 100
VCM/2D UTP/CAT 5
60
100
300
150 600
2×2,52
N° Master
N° Slave
XDV/304 La
Lb
Master () N° Slave ()
VCM/1D UTP CAT5
3211 0373
Lithos
VAS/101 Lc
La+Lb Lc La+Lb+Lc
VCM/1D VCM/2D
100
UTP/CAT 5 100 100
2×12
25
2×2,52
60
. 6 – FA01429-RU – 067/2020 – © CAME S.p.A. – . –
3sec … beep!
, :
1. . 3 . . 2. . . . .
3- . . . . 4- . , ( 1 12) . 3 .
.
.
.. 77 — FFAA0011442299–RRUU — 076//22002200–©©CCAAMMEESS..pp..AA..–..– 106 45
VAS/101
. · DIN- (EN 50022) . · . . , .
1 ~
~
2 18 . + (*)
M1 M2 +
(*) .
A
VAS-101
230 . 50÷60
.
200
(, . )
. 10
70
43,5
– 18 . 1 A-0,5 A 1’/3′
7,5 57
4 DIN
25°C 70°C
–
0°C – +35°C
IP
IP 30
LVC/01
500 mm 800 mm 1550 – 1600 mm
. 8 – FA01429-RU – 067/2020 – © CAME S.p.A. – . –
( ).
, , ( ) , ( ). , .
1080 mm
94°
43,5 mm 77°
163,5 mm
500 mm
–
( ).
,
.
. ”
“.
–
“-
“. ( ).
, ( ), ( ). ( ). ( ).
.. 99 — FFAA0011442299–RRUU — 076//22002200–©©CCAAMMEESS..pp..AA..–..–
( ) ,
.
( ).
,
B
.
. ”
“.
–
«-
».
A
( ).
DPS LSI
LTP LCI
– DPS , – LTP , – LSI , – LCI .
PROG
. 10 – FA01429-RU – 067/2020 – © CAME S.p.A. – . –
, , ( ). , , ( ).
1 2
:
53x13x0,3
M1 M2 +
M1 BOUT
53x33x0,3
PROG M2
SW3
+
NO C
B B
9/6
.. 1111 — FFAA0011442299–RRUU — 076//22002200–©©CCAAMMEESS..pp..AA..–..–
1 BOUT
+
16-18 .
2
( )
12 – 1 A (.)
LVC/01
16-18 .
250 (100 )
99x207x30
– -25°C – +70°C
-15°C – +50°C
(IP)
IP 54
PAL/NTSC
LVC/01
680×512
1
1-10 ( 1 .)
M1 BOUT
M1 BOUT
PROG
RESET
PROG M2
M2 SW3
PROG
PROG
>3” <6”
SW3
P
RESET
PROG
M2
SW3
ROG
PROG
PROG
. 3 PROG. ( 6 ), PROG , . PROG , . .
. 12 – FA01429-RU – 067/2020 – © CAME S.p.A. – . –
M1
”
M1
PROG
PROG
.
/ A , .
M1 BOUT
PROG
RESET
PROG
M2
SW3
ROG
PROG
P
. ( ) AUX2 . , : , .
. .
M1 BOUT
PROG : PROG .
. –
30 .
PROG
RESET
PROG M2
M2 SW3
PROG
PROG
<1”
SW3
beep
.. 1133 — FFAA0011442299–RRUU — 076//22002200–©©CCAAMMEESS..pp..AA..–..–
M1
M1 BOUT
PROG
RESET
PROG M2
M2 SW3
PROG
P>RO3G” <6”
SW3
.. 3 PROG . ( 6 ), PROG , . PROG , . .
P
RESET
PROG
PROG
M2
SW3
ROG
PROG
. –
(
) AUX2 .
beep
, : , . .
PROG
. 14 – FA01429-RU – 067/2020 – © CAME S.p.A. – . –
M1 BOUT
PROG
RESET
PROG M2
M2 SW3
PROG
P<RO1G”
SW3
.
PROG : PROG . . –
30 .
M1 BOUT
M1 BOUT
M1 BOUT
PROG
RESET
PROG
RESET
PROG
M2
SW3
ROG
>3” PR<OG6”
. « » 3 PROG ; ( 6 ), PROG , , «-
PROG
M2
SW3
ROG
PROG
P
M1 BOUT
».
–
,
. , –
PROG : PROG .
–
30 .
PROG
.. 1155 — FFAA0011442299–RRUU — 076//22002200–©©CCAAMMEESS..pp..AA..–..–
. – . , . . . , .
CAME S.p.A.
Via Martiri Della Libertà, 15 31030 Dosson di Casier – Treviso – Italy tel. (+39) 0422 4940 – fax. (+39) 0422 4941
. 16 – FA01429-RU – 07/2020 – © CAME S.p.A. – . –
