KYUNGWOO - Logo

SMK-HXV Reader
User’ Manual

2020. 02. 11

Prepared Reviewed Approved
Park Jeguk

Revision History

Rev. Date Driscription Remark
1 2020.02.11  First Release Park Jeguk

Synopsis

This document is specifically-written manual for SMK Reader which is receiver and transmitter of wireless communication, which is to confirm user identifications under engine-start limiting function in heavy equipments.
SMK Reader is defined as followings; SMK Reader transmits a signal pattern by RFID 125 KHz in order to wake up Chipkey/Flipkey Tag. And then SMK Reader communicates with Chipkey/Flipkey Tag by 433 MHz wireless signal. SMK Reader decodes password-secured signals and transfer identification information to certification device which has a function of engine-start limiting, such as Cluster, MCU or ECU, with using CAN protocol

Product Image

  1. External Appearance
    KYUNGWOO SMK HXV Reader - Product Image 1KYUNGWOO SMK HXV Reader - Product Image 2
  2. Dimension
    KYUNGWOO SMK HXV Reader - Dimension 1KYUNGWOO SMK HXV Reader - Dimension 2
  3. Certification LABEL location
    KYUNGWOO SMK HXV Reader - Certification LABEL location 1

Block Diagram

KYUNGWOO SMK HXV Reader - Block Diagram 1

Specification

  1. Operating Specification
    • Must transmit a signal of RFID 125 KHz as a wake up pattern signal.
    • Must be activated from 12 Vdc/24 Vdc external voltage supply.
    • Must be able to analyze the password-secured signal.
    • Must be able to use Single channels with band of 433MHz.
  2. Power Specification
    • Rated Voltage: 12V RIDGID R86012PD 1 2 Inch 18V Brushless Impact Wrench - icon3 (Max 50mA) / 24V (Max 30mA) both available
  3. General Specification
    • Storage Temperature: -40ºC ~ 85ºC
    • Operating Temperature: -20ºC ~ 50ºC
    • Water-Proof Specification: IP00
    • Communication with equipment: CAN2.0 250Kbps/500Kbps
    (*It is recommended to use twist shield cable and should be connected through a short distance as possible.)
    • Material of Device: PC (Substance : 3025N1, Flame Class : V0, Manufacturer : SAMYANG)
    PCB Material
    object/part No. manufacturer/ trademark type/model technical data UL No. mark(s) of
    conformity 1)
    SMK READER B/D PCB JM ELECTRONICS CO LTD D V-0 ; 105 °C E117655 JM
  4. RF Specification Item
    Item Specification
    Wireless Data Communication
    System
    Frequency 433MHz (Single Channels)
    RF Power Under 1 mW
    Modulation Method GFSK
    Tested Temperature -20 – +50″C
    Magnetic Induction System Frequency 125KHz (Single Channel)
    RF Power Under 105 d131.1v/m 0 3 meter
    Modulation Method ASK
  5. Product label Explanation of graphic symbols used
    Symbol Description
    Korea Certification Marking
    Communaute Europeenne Marking
    Electrical waste and electronics equipment
    Federal Communication Commision Marking
    Direct current

Postal address:
Kyungwoo Systech, Inc. Office: +82-2-985-8085
#401, Daeryung Post Tower 5, 68, Digital-ro 9, Geumcheon-gu, Seoul, South Korea
E-mail: Webmaster@kyungwoo.com

FCC Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

RED Compliance Statement
This product is CE marked according to the provision of the RED (2014/53/EU). Hereby Kyungwoo Systech, Inc. declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU

www.kyungwoo.com
Copyright © 2014 Kyungwoo Systech Inc.

Documents / Resources

KYUNGWOO SMK-HXV Reader [pdf] User Manual
SMK-HXV-10, SMKHXV10, ZE8-SMK-HXV-10, ZE8SMKHXV10, SMK-HXV Reader, SMK-HXV, Reader

References

Leave a comment

Your email address will not be published. Required fields are marked *