M200BT Multimedia Speaker System
Instruction Manual

Operation Description

1. The USB power plug of the speaker is plugged in.
2. Turn on the power and enter the LINE function by default. The red LED is always on. At this time, the audio cable can be inserted into the audio device to play music.
3. Short press the button on the remote control to enter the Bluetooth status, and the blue LEDs will flash alternately. At this time, you can pair the Bluetooth device. After the pairing is successful, there will make a notification sound. The blue LED is always on. At this time, the audio device can play music.
4. Short press the button on the remote control to stop playing music, and click again to resume playback. A short press on the remote control, increases the volume, press twice consecutively to go to the previous song, long press button on the remote control to increase the volume, and the speaker sounds louder. A short press on the remote control, the volume decreases, press twice consecutively to go to the next track, long press button on the remote control to decrease the volume, and the speaker sound is reduced.
5. Pairing: In the Bluetooth status, long-press the button on the remote control for 3 seconds. When the speaker will make a notification sound, it indicates that the current pairing device is released and the pairing mode is entered. The blue LED flashes alternately. At this time, Bluetooth device pairing can be performed.
6. After pressing the button on the remote control to enter the Bluetooth mode. If there is a paired device, it will return to the paired device. If there is no paired device, it will enter the pairing mode.
7. In pairing mode, search for the Bluetooth pairing device 3 times, and it will automatically turn off if there is no signal for 5 minutes in Bluetooth mode.
8. Turn off: Long press the button for 3 seconds to turn off the power and the LED.
9. After restarting, the volume level will automatically return to the middle value, and the last volume level will not be remembered.

Button Function

	Status	Function	Button Operation	Description
1	Turn off	Turn on	Short press the button	The red LED is on when the USB power cord of the speaker is plugged in and enters LINE mode
	Power on	Bluetooth	Short press button	Blue LED flash alternately and enter pairing status. The blue LED is always on.
	Power on	Line	Short press button	When the speaker will make a notification sound, it indicates that the current LINE mode is entered. The red LED is always on.
	Power on	Turn off	Long press the button for 3 seconds	Turn off the power and LED.
2	Bluetooth / Line	Increase Volume	Short press button Long press button	Short press the button to increase volume. Long press the button increase volume continuously.
3	Bluetooth / Line	Decrease Volume	Shot press button Long press  .1 button	Short press the button to decrease the volume Long press the button to decrease the volume continuously.
4	Bluetooth	Previous Track	Press twice button	Press twice button consecutively to go to the previous track

	Status	Function	Button Operation	Description
5	Bluetooth	Next Track	Press twice button	Press twice button consecutively to go to the next track
6	Play music	Pause	Short press button	Short press button to stop playing music, and click again to resume playback.
	Line	Mute	A short press button	Short press the button and enters mute status. Press it again, and the music unmute.
7	Bluetooth	PAIR	Long press the button for 3 seconds	Long press the button for 3 seconds. When the speaker will make a notification sound, it indicates that the current pairing device is released and the pairing mode is entered. The blue LED flashes alternately. At this time, Bluetooth device pairing can be performed.
8		RGB lighting touch control	Switch between ten lighting modes	Touch RGB lighting the button can switch between ten lighting modes.

FCC warning:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

Documents / Resources

KYE SYSTEMS M200BT Multimedia Speaker System [pdf] Instruction Manual 200BT, FSU200BT, M200BT, Multimedia Speaker System, M200BT Multimedia Speaker System

References

• User Manual