Kruger and Matz KM0827 Projection Alarm Clock Radio
Specifications
- AM/FM radio
- 20 stations memory (10 FM / 10 AM)
- Double alarm
- Time projection function
- Sleep & Snooze Function
- Display LED
- Speaker 8 Ohm / 0,5 W
- Radiofrequency
- AM 522 – 1620 kHz
- FM 87,5 – 108 MHz
- Power consumption 5 W
- Battery 2x AAA 1,5 V (for clock memory)
- Power supply 230 V / 50 Hz
- Dimensions 152 x 100 x 60 mm
- Weight 341 g
SAFETY INSTRUCTIONS
Read the entire instruction manual before you start installation and assembly and keep it for future reference.
- Protect this device from humidity, water, and other liquids.
- Before connecting the device to the power supply socket, make sure the voltage indicated on the appliance corresponds to the voltage in the power supply socket.
- Position the device in a properly ventilated place. Protect the device from heat sources and extreme temperatures.
- Clean the device with a soft, slightly damp cloth. Do not use any chemical agents to clean this device.
- Disconnect the device from power outlet, if it is not going to be used for a long time. Store the device without the batteries inside.
- Never disassemble this device. In case of damage, contact the authorized service point for a repair.
- Do not store magnet-sensitive items near the device.
- Do not connect any external antennas to the existing antenna.
PRODUCT DESCRIPTION
- Radio button
- Band changing button
- Saved radio preset button
- Time set button
- Dimmer button
- Snooze button
- Sleep timer button
- Alarm 1 / Volume – button
- Alarm 2 / Volume + button
- Time projection on/off/flip button
- HOUR / Tuning – button
- MIN / Tuning + button
- Alarm 1 buzzer indicator
- Alarm 1 radio indicator
- Alarm 2 buzzer indicator
- Alarm 2 radio indicator
- Focus adjustment wheel
OPERATION
To turn on the device, plug the power cord tintoa power outlet. After inserting the batteries, the time settings will be kept after the power cutout.
Setting the clock
- The first time the device is turned on, the display will show a flashing 0:00, indicating that the clock is not set.
- Press the HOUR button to set the hour. Press the MIN button to set the minutes. Press and hold the HOUR or MINUTE button to quickly change the time.
- After setting the correct time, press the time set button or wait 5 seconds. After 5 seconds, the time will be set.
To change the set time:
- Make sure that the radio is switched off.
- Press and hold the set time button, until the time on display flashes.
- Repeat steps 2-3 from the previous paragraph.
Setting the alarm
Attention if you want the alarm sound to be the radio, set the radio and the volume before setting the alarm.
- Make sure that the radio is switched off.
- Press and hold the Alarm 1 or Alarm 2 button, until the time on display flashes.
- Use the HOUR and MIN buttons to set the alarm time.
- Press the Alarm 1 or 2 button to confirm the alarm time (or wait 5 seconds).
- Press the Alarm 1 or 2 button again to choose the alarm sound radio or buzzer.
After the alarm is activated at the set time:
- Press the Radio button to turn off the alarm.
- Press the snooze button to activate the 9-minute snooze.
- To turn off the snooze, press the Radio button.
- If the alarm is not deactivated by the button, it will turn off automatically after one hour.
- Alarm will switch on after 24 hours. To turn off the alarm, keep pressing the Alarm 1 or 2 button, until the alarm indicator turns off.
Set timer
The device has automatic timer functions. To set it up:
- While listening to the radio, press the timer button. A number 90 will appear on the display, indicating the time to automatically switch off.
- Keep pressing the snooze button until you reach the desired time.
- After 2 seconds from the selected off time, the display will show the current time again and the radio will turn off after the set time.
- Press the timer button to display the time to turn off.
- To turn off the timer function, keep pressing the timer button until OFF appears on the display, or turn off the radio.
FM Radio
- Press the Radio button to turn on the radio. The display will show the current frequency and the current time after 5 seconds.
- Press the Radio button to turn off the radio.
- Press the band button to change the radio band.
- To change the volume level, use the volume buttons.
- To set the frequency, use the tuning buttons.
- To enable automatic channel scanning, press and hold one of the tuning buttons.
Saving radio stations
- Set the frequency.
- Press and hold the time set button. The channel number will appear on the display. Press the time set button again to save the frequency on the preset.
- Each frequency will be saved one after another on presets 1 to 10. If the channel already has a frequency saved, the saved station will be overwritten.
- To go to the saved channel (while listening to the radio), press the saved radio presets button. A saved station will be selected, and the channel number will appear on the display.
Time projection
Press the time projection button to turn the projector on or off. Position the projector lens, so that it displays the time on a wall or other surface. Use the focus adjustment wheel to make the time clear. Press and hold the time projection button to flip the time vertically.
Battery back-up
When batteries (2x AAA 1.5V batteries) are inserted into the device, the currently set time will be maintained during a power outage. During a power outage, the display will not be illuminated. When power is restored, the correct time will be set. If there is no power for a long time, or the battery level is low, the restored time may be different from the correct time. Take out the batteries if the device is not going to be used for a long time.
FAQs
Q: How do I set the alarm on the Projection Alarm Clock Radio?
A: To set the alarm, follow these steps:
- Press the Alarm 1 or Alarm 2 button until the alarm indicator is displayed.
- Set the desired wake-up time using the Hour and Minute buttons.
- To activate snooze, press the Snooze button.
Q: How do I save radio presets on the device?
A: To save radio presets, tune to your desired station and press the Saved Radio Presets button to store it for easy access later.
Documents / Resources
 |
Kruger and Matz KM0827 Projection Alarm Clock Radio [pdf] Owner's Manual KM0827 Projection Alarm Clock Radio, KM0827, Projection Alarm Clock Radio, Alarm Clock Radio, Clock Radio |
