KRAMER FC-6 Ethernet Gateway
Specifications
- Model: FC-6 Ethernet Gateway
- Manufacturer: Kramer
- Power Input: USB or optional 5V DC
- Default IP: 192.168.1.39
Product Usage Instructions
Step 1: Check what’s in the box
Make sure the package includes the FC-6 Ethernet Gateway, rubber feet, USB A to USB mini cable, quick start guide, and bracket set.
Step 2: Get to know your FC-6
Learn about the different features of your FC-6, including the IR sensor, LAN RJ-45 connector, LEDs, reset button, USB connector, DIP switches, terminal blocks, and power connectors.
Step 3: Install the FC-6
Mount the FC-6 in a suitable location using the provided bracket set. Ensure it is placed near a power source for easy connectivity.
Step 4: Connect the inputs and outputs
Before connecting devices, power off each device. Use high-performance cables to connect equipment to the FC-6 for optimal performance.
Step 5: Connect the power
Connect the FC-6 to a USB power source or optional 5V DC power supply. Always use the provided Kramer Electronics power supply for safety.
Step 6: Configure and operate the FC-6
Identify the assigned IP address of the FC-6 using the K-LAN Configurator. To reset to factory default settings, follow the steps mentioned in the manual. Access the Web UI using the default hostname.
Frequently Asked Questions
- Q: How do I reset the FC-6 to factory default settings?
- A: Turn off the power, press and hold the Reset button, turn on the power while holding the button, and release the button after a few seconds to reset.
- Q: What is the default IP address of the FC-6?
- A: The default IP address is 192.168.1.39.
- Q: Where can I download firmware upgrades for the FC-6?
- A: Visit www.kramerav.com/downloads/FC-6 to download the latest user manual and firmware upgrades.
Quick Start Guide
This guide helps you install and use your FC-6 for the first time. Go to www.kramerav.com/downloads/FC-6 to download the latest user manual and check if firmware upgrades are available
Step 1: Check what’s in the box
- FC-6 Ethernet Gateway
- 4 Rubber feet
- 1 Bracket set
- 1 USB A to USB mini cable
- 1 Quick start guide
Step 2: Get to know your FC-6
| # | Feature | Function |
| 1 | IR Sensor | Sensor for IR learning |
| 2 | LAN RJ-45 Connector | Connects to an IP client or other controller, either directly or via a LAN |
| 3 | Port 1 and 2 white (upper) and blue LEDs | Show the transmission status of port 1 and port 2:
When set as RS-232, the white LED indicates Tx and blue LED indicates Rx When set as IR, the white LED indicates IR-P1 Tx and blue LED indicates IR-P2 Tx |
| 4 | RESET Button | Press and hold while cycling the device power to reset to factory default parameters |
| 5 | SERVICE Mini USB Connector | Connects to a USB power source for powering and to a PC for a local firmware upgrade |
| 6 | ON LED | Lights green when the unit is powered on |
| 7 | MODE DIP-switches (Port 1 and Port 2) | Switch up for RS-232, switch down for IR
The default setting is port 1 RS-232 (up) and port 2 IR (down) |
| 8 | Port 1 and 2 I/O 3-pin Terminal Block | Each terminal block connects one bidirectional RS-232/RS-485 port or two IR outputs |
| 9 | 5V DC Connector | Connects to an optional 5V DC power supply, center pin positive. Not needed when the device is supplied power by a USB power source |
Install the FC-6
Step 3: Install the FC-6
You can mount this Kramer PicoTOOL™ next to a USB power source behind an AV device, in-room ceiling area, on a desktop, wall or similar area. Install FC-6 using one of the following methods:
- Attach the rubber feet and place the unit on a flat surface.
- Fasten a bracket (included) on each side of the unit and attach it to a flat surface. For more information go to www.kramerav.com/downloads/FC-6.
- Mount the unit in a rack using an optional RK-4PT rack adapter
Step 4: Connect the inputs and outputs
Always switch OFF the power on each device before connecting it to your FC-6. For best results, we recommend that you always use Kramer high-performance cables to connect controlled equipment to the FC-6.
Step 5: Connect the power
Connect a USB power source and/or an optional 5V DC power supply to the FC-6 and plug it into the mains electricity.
Safety Instructions
- Caution:
- There are no operator-serviceable parts inside the unit.
- Warning:
- Use only the Kramer Electronics power supply that is provided with the unit.
- Warning:
- Disconnect the power and unplug the unit from the wall before installing it.
See www.KramerAV.com for updated safety information.
Step 6: Configure and operate the FC-6
Note: The FC-6 arrives with the default IP 192.168.1.39. To connect the FC-6 on the first installation, you must identify what IP address has been automatically assigned to the FC-6. To discover the IP address of FC-6, use K-LAN Configurator, available for download from our website at www.kramerav.com.
To reset the device to its factory default settings:
- Turn off the power to the device.
- Press and hold the Reset button on the front panel.
- Turn on the power to the device while holding down the Reset button for a few seconds.
- Release the button. The device is reset to the factory default settings.
To browse the FC-6 Web UI (User Interface) using factory default settings: Use the default hostname: FC-6-xx, where xxxx are the last four digits of the serial number of the device.
To configure and operate the FC-6:
- Using the device Web UI, configure the control gateway:
- Set DHCP or assign a static IP address
- Associate IP port(s) with the relevant port(s)
- Configure the relevant port parameters
- Configure IP client connection port(s) on a Kramer control or any other control software application.
- Set the control application to use the control gateway ports for sending and receiving control communication over the IP connections
Documents / Resources
 |
KRAMER FC-6 Ethernet Gateway [pdf] User Guide FC-6 Ethernet Gateway, FC-6, Ethernet Gateway, Gateway |