KOSO logo

KOSO logo2

D2 Multifunction Meter Instructions

icon1

Thank you for purchasing our product. This product is a multifunction meter and is easy to install. Before using, read the instructions carefully and retain them for future reference.
warning 2 Attention!

  • For installation, follow the steps described. Any damage caused by the wrong installation shall be imputed to the users.
  • To avoid a short circuit from occurring do not pull or modify the wires during installation.
  • Do not disassemble or change any parts. Opening and disassembling this unit will void any warranty.
  • Maintenance and repairs should be executed by our professionals only.

◎ Symbol description:

icon2

NOTE
warning 2 Some procedures must be followed to avoid damage to the instrument.
warning 2 WARNING! Certain procedures must be followed to avoid damages to yourself, to the vehicle or others.

Accessories

KOSO D2 Multifunction Meter - fig1

Wiring Installation Instructions

KOSO D2 Multifunction Meter - fig2

2-2 Vehicle installation instructions

KOSO D2 Multifunction Meter - fig3

Disassemble in the following order
❶ LCD Meter
❷ The original wiring harness
NOTE
Refer to the sequence of the drawing for the removal. Perform the assembly in a sequence reverse to the removal.
warning 2 Before assembly, assemble the
❶ LCD Meter in advance (refer to 2-3 Installation Instruction).

2-3 Installation instructions

KOSO D2 Multifunction Meter - fig4

Follow the steps below

  1. Meter bracket (from original supplier)
  2. Waterproof outer lining (from original supplier) +LCD Meter (Accessory1)
  3. Bushing (from original supplier)
  4. Screw (from original supplier)

Overview

KOSO D2 Multifunction Meter - fig5

3-2  Features and settings description

●Speedometer Display range: 0~199 km (0~124 mile) switchable
Display unit: 1 km (mile)
○Display interval <0.5 second
○Internal and external
odometer
Display range : 000,000~999,999 km (mile) returns to zero upon exceeding
Display unit: 1 km (mile)
○Trip meters A,B Display range : 0,000.0~9,999.9 km (mile) returns to zero upon exceeding
Display unit : 0.1 km (mile)
○Tire circumference Setting range : 50 ~ 210 %
Setting unit: 1 %
●Tachometer Display range : 0 ~ 10,000 RPM
○Shift light warning Setting range : 2,000 ~ 10,000 RPM
Setting unit: 100 RPM
When it is higher than the setting value (including), the backlight will blink in red and white as a warning.
●Engine temperature Setting range : -39 ~ 300 °C (-38 ~ 572 °F)
●Clock Setting range: 12 / 24-hour format
●Voltmeter Display range: 8 ~ 18 V
●Backlight brightness Setting range : 1 /5(darkest)~ 5 / 5(brightest)
○Backlight color Setting range: white, red, orange, yellow, green, blue, light blue, purple
●Mileage Maintenance Setting range : Off, 500 ~ 16,000 km (300 ~ 10,000 mile)
Setting unit: 100 km (miles)
●Tire pressure Display range : —, Hi, 0~73 PSI, 0~506 kPa, 0.0~5.0 bar
Display unit : 1 PSI, 1 kPa, 0.1 bar
(TPMS, FR/RR/LR shall be displayed when the  vehicle supports TPMS)
●Fuel meter Display range: 10 levels
●Operating voltage DC 12 V
●Operating temperature -20~85 °C
○Storage temperature -30~90 °C
●Specifications JIS D 0203 (S2)
●Meter size 88.2 x 67.0 x 35.2 mm
●Meter weight Around 70 g
●Indication light Right indication light (Green)KOSO D2 Multifunction Meter - fig6
Security light (Red)
ABS light (Amber)
Motor oil light (Red)
Neutral light (Green)
High beam light (Blue)
Low fuel warning light (Amber)
Left indication light (Green)
Fog light (Green)
Battery discharge light (Red)
Engine light (Amber)
Cruise light (Green/Amber)
Tire pressure warning light (Amber)

NOTE Design and specification may change without further notice.

3-3 Main menu functions

KOSO D2 Multifunction Meter - fig7

  • In the total mileage screen, press the button once to switch to Trip A screen.
  • In the total mileage screen, hold the button for 3 seconds to enter into the setting screen.(refer to setting 4)
    KOSO D2 Multifunction Meter - fig8
  • Trip A screen, press the button once to switch to Trip B screen.
  • Hold the button for 3 seconds to clear the Trip A recordings.
    desply2
  • Trip B screen, press the button once to switch to the mileage maintenance screen.
  • Hold the button for 3 seconds to clear the Trip B recordings.
    desply1NOTE Display can be switched off (refer to setting 4-6-1)
    KOSO D2 Multifunction Meter - fig9
  • In the mileage maintenance screen, press the button once to switch to the remaining mileage screen.
  • Mileage maintenance will count down from setting value, when it reaches 0, the screen will blink to indicate mileage reached.
    KOSO D2 Multifunction Meter - fig10
  • When the reminding feature is activated, it will automatically return to the mileage maintenance screen once the mileage maintenance value is reached.
    KOSO D2 Multifunction Meter - fig11
  • Hold the button for 3 seconds to switch to inform function switch.
    KOSO D2 Multifunction Meter - fig12NOTE It will not display if it’s not supported by the engine computer.
  • Hold the button for 10 seconds to clear the mileage maintenance recordings.
KOSO D2 Multifunction Meter - fig13 ○At 0 seconds, start holding the button.
○In the 3rd second, the inform feature will blink once.
○In the 5th second, inform feature will switch back,   mileage display will begin blinking.
○During the 6~9th seconds,   if the button is released,   it will cancel the process.
○On the 10th second, the mileage maintenance record is cleared.

NOTE Display can be switched off (refer to set 4-7)

KOSO D2 Multifunction Meter - fig14

  • In the remaining mileage screen, press the button once to switch to the clock screen.
  • When the vehicle range is too low, “r Lo ” it will be displayed to notify the user.
    KOSO D2 Multifunction Meter - fig15
  • When the reminding feature is activated, it will automatically return to the remaining screen, if the remaining mileage is too low.
  • When the reminding feature is activated, it will automatically switch to the remaining mileage screen during startup, if the remaining mileage is too low.
    KOSO D2 Multifunction Meter - fig16
  • Hold the button for 3 seconds to switch to inform feature switch.
    KOSO D2 Multifunction Meter - fig17NOTE It will not display if it’s not supported by the engine computer.
    KOSO D2 Multifunction Meter - fig18
  • In the clock screen, press the button once to switch to the engine temperature screen.
    NOTE Display can be switched off (refer to setting 4-1)
    KOSO D2 Multifunction Meter - fig19
  • In the engine temperature screen, press the button once to switch to the voltage screen.
    NOTE Display can be switched off (refer to setting 4-6-2)
    KOSO D2 Multifunction Meter - fig20
  • In the voltage screen, press the button once to switch to the tire pressure screen.
    NOTE Display can be switch off (refer to setting 4-6-3)
    warning 2 The screen may be shifted to the tire pressure screen when the vehicle supports TPMS.
    KOSO D2 Multifunction Meter - fig21
  • In the tire pressure screen, press the button once to return to the total mileage screen.
    KOSO D2 Multifunction Meter - fig22

Setting Screen Switching Description

  • Press the button for 3 seconds on the main screen to switch to the setting screen.
  • Press the button to select
  1. Clock
  2. Unit(Speed/Temperature/tire pressure)
  3. Backlight(Mode/Brightness/Color)
  4. The tire circumference
  5. The RPM shift light warning
  6. Features display
  7. Mileage maintenance
  8. Total internal and external mileage

NOTE During setting, if the button is not pressed in 30 seconds, it will automatically return to the startup screen.

KOSO D2 Multifunction Meter - fig23

4-1 Clock settings

KOSO D2 Multifunction Meter - fig24

  • In the clock settings screen, hold the button for 3 seconds to enter into the setting screen.
    KOSO D2 Multifunction Meter - fig25KOSO D2 Multifunction Meter - fig26
  • Example: If want to set time to 12-hour format.
  • Press the button once to select a desired setting value.
    warning 2 Now the setting value will blink.
    NOTE Setting range : 12h / 24h
    Default value : 24h
    KOSO D2 Multifunction Meter - fig27
  • EX: Set time settings from a 24-hour format to 12-hour format.
  • Hold the button for 3 seconds to enter time into the (hour/minute) setting screen.
    KOSO D2 Multifunction Meter - fig28
  • Example: Set time to 01:05 AM.
  • Hold the button for 3 seconds to move the cursor to the desired settings level.
    KOSO D2 Multifunction Meter - fig29warning 2 Now the setting value will blink.
  • Press the button once to select the desired setting value.
    KOSO D2 Multifunction Meter - fig30NOTE Setting range :
    Hour : 1~12 (12 h) / 0~23 (24 h)
    Minute: 00~59 minutes.
    Default value :
    Hour : 12(12h)/0(24h).
    Minute : 0.
    KOSO D2 Multifunction Meter - fig31
  • EX : Set time clock setting from 0:00 to 1:05.
  • Hold the button for 3 seconds to return to the clock settings main screen.
    KOSO D2 Multifunction Meter - fig32
  • Clock settings main screen.
  • Press the button once to enter next setting.

4-2 Speed, temperature, tire pressure unit settings

KOSO D2 Multifunction Meter - fig33

  • In the speed, temperature, tire pressure unit settings main screen, hold the button for 3 seconds to enter into the main screen.
    KOSO D2 Multifunction Meter - fig34●Example : To set speed unit to MPH(mile).
    ●Press the button once to select the desired value.
    warning 2 Now the setting value will blink.
    NOTE Setting range : km/h, MPH.
    Default value : km/h.
    NOTE Total mileage and distance meter unit will vary according to the speed unit.
    KOSO D2 Multifunction Meter - fig35
  • EX : Set speed unit from km/h to MPH.
  • Hold the button for 3 seconds to enter into the temperature unit settings screen.
    KOSO D2 Multifunction Meter - fig36
  • Example: To set the temperature unit to ˚C.
  • Press the button once to select the desired value.
    warning 2 Now the setting value will blink.
    NOTE Setting range :
    ˚C(Celsius) and ˚F(Fahrenheit).
    Default value: ˚F(Fahrenheit).
    KOSO D2 Multifunction Meter - fig40
  • EX : Set temperature unit from
    ˚F(Fahrenheit) to˚C(Celsius).
  • Hold the button for 3 seconds to enter into the tire pressure unit settings screen.
    warning 2 The screen may be shifted to the tire pressure unit setting screen when the vehicle supports TPMS.
    KOSO D2 Multifunction Meter - fig41
  • Example: To set tire pressure unit to BAR.
  • Press the button once to select the desired value.
    warning 2 Now the setting value will blink.
    NOTE Setting range: PSI, BAR, and KPA.
    Default value: PSI
    KOSO D2 Multifunction Meter - fig42
  • EX : Set tire pressure unit from PSI to BAR.
  • Hold the button for 3 seconds to return to the speed, temperature and tire pressure unit settings main screen.
    KOSO D2 Multifunction Meter - fig43
  • Speed, temperature, and tire pressure unit settings main screen.
  • Press the button once to enter the next setting.

4-3 Backlight brightness settings (Mode/ Brightness/ Color)

KOSO D2 Multifunction Meter - fig37

  • In the backlight (mode /color/brightness) settings main screen, hold the button for 3 seconds to enter into the settings screen.
    KOSO D2 Multifunction Meter - fig38
  • Example: To set the mode to Night mode.
  • Press the button once to select the desired value.
    warning 2 Now the setting value will blink.
    NOTE Setting Auto(automatically switches according to the light : day mode display for a bright environment and Night mode display for a dark environment),
    Day mode, Night mode.
    Default value: Auto.
    KOSO D2 Multifunction Meter - fig39
  • EX: Set background from Auto mode to Night mode.
  • Hold the button for 3 seconds to enter the backlight color(day) setting.
    KOSO D2 Multifunction Meter - fig44
  • Example: To set backlight color(day) to blue.
  • Press the button once to choose the color.
    warning 2 Now the setting value will blink.
    NOTE Setting range: White, Red, Orange, Yellow, Green, Blue, Indigo, Purple.
    Default value: White.
    NOTE The backlight color will change immediately after you set the value.
    KOSO D2 Multifunction Meter - fig45
  • EX: Set backlight color(day) from white to blue.
  • Hold the button for 3 seconds to enter the backlight brightness(day) setting.
    KOSO D2 Multifunction Meter - fig46
  • Example: To set the backlight brightness (day) to 4/5 (80%).
  • Press the button once to select the desired value.
    warning 2 Now the setting value will blink.
    NOTE Setting range: 3/5~ 5/5 (Brightest), 3 different levels available.
    Setting unit: 20% per level.
    Default value : 5/5(100%).
    NOTE The backlight brightness will change immediately after you set the value.
    KOSO D2 Multifunction Meter - fig47
  • EX: The backlight brightness (day) setting is changed from 5/5 (100%) to 4/5 (80%).
  • Hold the button for 3 seconds to enter the backlight color (night) setting.
    KOSO D2 Multifunction Meter - fig48
  • Example: To set backlight color(night) to Yellow.
  • Press the button once to choose the color .
    warning 2 Now the setting value will blink.
    NOTE Settings range White, Red, Orange, Yellow, Green, Blue, Indigo, Purple.
    Default value: White.
    NOTE The backlight color will change immediately after you set the value.
    KOSO D2 Multifunction Meter - fig49EX: Set backlight color(night) from White to Yellow.
  • Hold the button for 3 seconds to enter the backlight brightness(night) setting.
    KOSO D2 Multifunction Meter - fig59
  • Example: To set the backlight brightness (night) to 2/5 (40%).
  • Press the button once to select the desired value.
    warning 2 Now the setting value will blink.
    NOTE Setting range: 1/5(Darkest)~ 5/5 (Brightest), 5 different levels available.
    Setting unit: 20% per level.
    Default value : 3/5(60%).
    NOTE The backlight brightness will change immediately after you set the value.
    KOSO D2 Multifunction Meter - fig60
  • EX: The backlight brightness (night) setting is changed from 3/5 (60%) to 2/5 (40%).
  • Hold the button for 3 seconds to return to the backlight (Mode/ Brightness/Color) settings main screen.
    KOSO D2 Multifunction Meter - fig61
  • Backlight (Mode/ Brightness/ Color) settings main screen.
  • Press the button once to enter the next setting.

4-4 The tire circumference settings

KOSO D2 Multifunction Meter - fig50

  • In the tire circumference setting, hold the button for 3 seconds to enter into the setting screen.
    KOSO D2 Multifunction Meter - fig51KOSO D2 Multifunction Meter - fig52
  • Example: To set the tire circumference to 105%.
  • Hold the button for 3 seconds to move the cursor to the desired settings level.
    KOSO D2 Multifunction Meter - fig53warning 2 Now the setting value will blink.
  • Press the button once to select the desired value.
    KOSO D2 Multifunction Meter - fig54NOTE Setting range : 50 ~ 210%.
    Default value : 100%.
    KOSO D2 Multifunction Meter - fig62
  • Example: Set tire percentage from 100% to 105%.
  • Hold the button for 3 seconds to return to the tire circumference main screen.
    KOSO D2 Multifunction Meter - fig63
  • Tire percentage settings main screen.
  • Press the button once to enter next setting.

4-5 The RPM shift light warning settings

  • KOSO D2 Multifunction Meter - fig55In the RPM shift light warning settings main screen, hold the button for 3 seconds to enter into the main screen.
    KOSO D2 Multifunction Meter - fig56KOSO D2 Multifunction Meter - fig57
  • Example: To set the shift light warning value to 5,700 r.
  • Hold the button for 3 seconds to move the cursor to the desired settings level.
    KOSO D2 Multifunction Meter - fig58warning 2 Now the setting value will blink.
  • Press the button once to select a desired setting value.
    KOSO D2 Multifunction Meter - fig64NOTE Setting range : 2,000 ~ 10,000 RPM.
    Default value : 5,500 RPM.
    KOSO D2 Multifunction Meter - fig65
  • EX : Set shift light warning value from 5,500 r to 5,700 r.
  • Hold the button for 3 seconds to return to the RPM shift light warning settings screen.
    KOSO D2 Multifunction Meter - fig66
  • The RPM shift light warning settings main screen.
  • Press the button once to enter next setting.
  • When the value of rotation speed reached the value set, the main screen’s backlight will blink in red and white as a warning.
    KOSO D2 Multifunction Meter - fig73

4-6 Features display settings

KOSO D2 Multifunction Meter - fig80

  • In the display settings main screen, hold the button for 3 seconds to enter into the sub settings screen.

4-6-1

KOSO D2 Multifunction Meter - fig67

  • In Trip B display settings main screen, hold the button for 3 seconds to enter into the settings screen.
    KOSO D2 Multifunction Meter - fig68
  • Example: To hide (H) trip B display.
  • Press the button once to select the desired value.
    warning 2 Now the setting value will blink.
    NOTE Setting range: Hidden (H), Show (S).
    Default value: Show (S).
    KOSO D2 Multifunction Meter - fig69
  • EX: Set type B display from the show (S) to hidden (H).
  • Hold the button for 3 seconds to return to the trip B display settings main screen.
    KOSO D2 Multifunction Meter - fig70
  • Trip B display settings main screen,  hold the button for 3 seconds to enter into the engine temperature display settings main screen.
    4-6-2
    KOSO D2 Multifunction Meter - fig71
  • In the engine temperature display settings main screen, hold the button for 3 seconds to enter into the settings screen.
    KOSO D2 Multifunction Meter - fig72
  • Example: To hide (H) the engine temperature display.
  • Press the button once to select the desired value.
    warning 2 Now the setting value will blink.
    NOTE Setting range: Hidden (H), Show (S).
    Default value: Show (S).
    KOSO D2 Multifunction Meter - fig74
  • EX: Set engine temperature display from the show (S) to hidden (H).
  • Hold the button for 3 seconds to return to the engine temperature display settings main screen.
    KOSO D2 Multifunction Meter - fig75
  • Engine temperature display settings main screen.
  • Press the button once to enter into the voltage display settings main screen.
    KOSO D2 Multifunction Meter - fig76
  • In the voltage display settings main screen, hold the button for 3 seconds to enter into the settings screen.
    KOSO D2 Multifunction Meter - fig77
  • Example : To hide (H) voltage display.
  • Press the button once to select the desired value.
    warning 2 Now the setting value will blink.
    NOTE Setting range: Hidden (H), Show (S).
    Default value: Show (S).
    KOSO D2 Multifunction Meter - fig78
  • EX : Set voltage display from show (S) to hidden (H).
  • Hold the button for 3 seconds to return to the voltage display settings main screen.
    KOSO D2 Multifunction Meter - fig79
  • Voltage display settings main screen.
  • Press the button once to enter into the feature display settings main screen.
    KOSO D2 Multifunction Meter - fig80
  • In the features display settings main screen.
  • Press the button once to enter next setting.

4-7 Mileage maintenance settings

KOSO D2 Multifunction Meter - fig81

  • In the mileage maintenance main screen, hold the button for 3 seconds to enter into the sub settings screen.
    KOSO D2 Multifunction Meter - fig82KOSO D2 Multifunction Meter - fig83
  • Example: To set mileage maintenance to (ON).
  • Press the button once to select the desired settings value.
    warning 2 Now the setting value will blink.
    NOTE Display range: ON, OFF.
    Default value: OFF.
    KOSO D2 Multifunction Meter - fig84
  • EX: Set mileage maintenance from OFF to ON.
  • Hold the button for 3 seconds to enter into the mileage maintenance main screen.
    NOTE When set to OFF, it will directly return to the mileage maintenance main screen.
    KOSO D2 Multifunction Meter - fig85
  • Example: To set mileage maintenance value to 800.
  • Hold the button for 3 seconds to move the cursor to the desired settings level.
    KOSO D2 Multifunction Meter - fig86warning 2 Now the setting value will blink.
  • Press the button once to select the desired setting value.
    KOSO D2 Multifunction Meter - fig87NOTE Setting range : 500 ~ 16,000 km (300 ~ 10,000 mile).
    Default value : 500 km(300 mile).
    KOSO D2 Multifunction Meter - fig88
  • EX: Set the mileage maintenance from 500 to 800.
  • Hold the button for 3 seconds to return to the mileage maintenance main screen.
    KOSO D2 Multifunction Meter - fig89
  • Mileage maintenance settings main screen.
  • Press the button once to enter into the next settings screen.

4-8 Total internal and external mileage settings

KOSO D2 Multifunction Meter - fig90

  • In the total mileage settings main screen, hold the button for 3 seconds to enter into the sub settings screen.
    4-8-1
    KOSO D2 Multifunction Meter - fig91
  • Example: Current total internal mileage display is 5 km.
  • Press the button once to enter into the total external mileage settings screen.
    warning 2 The user is unable to adjust or remove total internal mileage.
    NOTE Display range : 0 ~ 999,999 km (mile).
    4-8-2
    KOSO D2 Multifunction Meter - fig92
  • In the total external mileage settings main screen, hold the button for 3 seconds to enter into the loading screen for the total external mileage.
    KOSO D2 Multifunction Meter - fig93
  • Loading screen for the total external mileage, press and hold the button for 3 seconds to load the current vehicle mileage once.
    KOSO D2 Multifunction Meter - fig94
  • Example: To set external total distance value to 50,000 km.
  • Hold the button for 3 seconds to move the cursor to the desired settings level.
    KOSO D2 Multifunction Meter - fig95warning 2 Now the setting value will blink.
  • Press the button once to select a desired setting value.
    KOSO D2 Multifunction Meter - fig96NOTE Setting range : 0 ~ 999,999 km (mile).
  • KOSO D2 Multifunction Meter - fig97EX : Set the total external mileage from0 to 50,000 km.
  • Hold the button for 3 seconds to return to the total external mileage settings main screen.
    KOSO D2 Multifunction Meter - fig98
  • Total external mileage settings main screen.
  • Press the button once to return to the mileage settings main screen.
    KOSO D2 Multifunction Meter - fig99
  • Total mileage settings main screen.
  • Press the button once to return to startup screen.

Troubleshooting

The following situation does not indicate malfunction of the meter. heck the following points, before taking it in for repairs.

Trouble Check item Trouble Check item
The meter doesn’t work
when the power is on.
●The power isn’t supplied to the meter.
→Make sure the wiring is connected.
The wiring and fuse are not broken.
→The battery is too old to supthe ply needed
power (DC 12 V).
Speed is inaccurate. ●May be wrong settings.
→Check the settings menu to
confirm whether the setting for speed is correct.
The meter shows wrong
information.
●Check the voltage of your battery, and
make sure the voltage is over DC 12 V.
The clock is incorrect. ●May be wrong setting.
→Check the set list to see
whether the setting for the clock is correct.

SONY HT SC40 Sound Bar - icon4 If the problems still can’t be solved, contact our technical department for assistance.

wh080ba00a(9-9)

Documents / Resources

KOSO D2 Multifunction Meter [pdf] Instructions
D2 Multifunction Meter, D2, Multifunction Meter

Leave a comment

Your email address will not be published.