KORAD KEL2000 Series Communication Protocol

KORAD KEL2000 Series Communication Protocol

Contents hide
1 INSTRUCTIONS FOR USE
2 Documents / Resources
2.1 References
3 Related Posts

INSTRUCTIONS FOR USE

  1. *IDN?
    Return product information
    XXXX,KEL2000,SN:1214534454,V1.10
  2. *RCL<NR1>
    NR1 {1~100}
    *RCL 12
    Recall 12 units’ content
  3. *SAV<NR1>
    Save to the storage unit NR1{1~100}
    *SAV 13
    Note: *RCL can be recalled arbitrarily, and *SAV must be saved in CC, CV, CR or CW mode.
  4. *TRG
    Simulate a trigger, only valid in dynamic pulse (PL) mode and reversal (RL) mode.
  5. :SYSTem:BEEP<bool>
    Turn the beep ON or OFF.
    :SYST:BEEP ON
    Parameters: {1|0|ON|OFF}
    Query syntax
    :SYST: BEEP?
  6. :SYSTem:LOCK <boo>
    Turn ON and OFF the lock button
    :SYST:LOCK ON
    Parameters: {1|0|ON|OFF}
    Query syntax:
    :SYST:LOCK?
  7. :SYSTem:EXIT<NR1>
    1. Turn ON or OFF the external trigger
      :SYST: EXIT 1
    2. Turn ON the remote switch
      :SYST: EXIT 2
      Parameters: {2|0|OFF}
      Query syntax：
      :SYST: EXIT?
  8. :SYSTem:COMPensate <boo>
    Turn ON external compensation
    :SYST:COMP ON
    Parameters: {1|0|ON|OFF}
    Query syntax:
    :SYST:COMP?
  9. :STATus?
    Query the current status
    Query syntax:
    :STAT?
    Return:
    0,4,0,0,0,0
    0 Beep Beep status
    1. COM port baud rate (0,9600;1,19200;2,38400;3,57600;4,15200).
    2. The Key LOCK status
    3. External trigger status
    4. Remote compensation status
    5. Reverse connection status of load polarity (0-no reverse connection; 1-reverse connection)
  10. INPut <bool>
    Turn the load ON and OFF
    Command syntax:
    :INP 1
    Parameters: {1|0|ON|OFF}
    Query syntax:
    :INP?
  11. :VOLTage<NRf>
    Set the current CV voltage
    :VOLT 12.35V
    Parameters: {MIN~MAX:0.1V~150V }
    Query syntax:
    :VOLT?
  12. :VOLTage:UPPer<NRf>
    Set the maximum voltage value.
    :VOLT:UPP 18V
    Parameters: {MIN~MAX:0.1V~150V }
    Query syntax:
    :VOLT:UPP?
  13. :VOLTage:LOWer?
    Query the minimum voltage.
  14. :CURRent<NRf>
    Set the CC current.
    :CURR 3.350A
    Parameters: {MIN~MAX:0A ~40A }
    Query syntax:
    :CURR?
  15. :CURRent:UPPer<NRf>
    Set the maximum current value.
    :CURR:UPP 18A
    Parameters: {0A~40A }
    Query syntax:
    :CURR:UPP?
  16. :CURR:LOWer?
    Query the minimum current value.
  17. :RESistance<NRf>
    Set the CR resistance value.
    :RES 120.30OHM
    Parameters: { 0.2000OHM ~7500OHM }
    Query syntax:
    :RES?
  18. :RESistance:UPPer<NRf>
    Set the maximum resistance value.
    :RES:UPP 3600OHM
    Parameters: { 0.2000OHM~7500OHM }
    Query syntax:
    :RES:UPP?
  19. :RES:LOWer?
    Query the minimum resistance value.
  20. :POWer<NRf>
    Set CW power.
    :POW 12.5W
    Parameters: { 0W ~300W }
    Query syntax:
    :POW?
  21. :POW:UPPer<NRf>
    Set the maximum power value.
    :POW:UPP 18W
    Parameters: { 0W~300W }
    Query syntax:
    :POW:UPP?
  22. :POW:LOWer
    Query the minimum power value.
  23. :MEASure:VOLTage?
    Query output voltage value.
  24. :MEASure:CURRent?
    Query output current value.
  25. :MEASure:POWer?
    Query output power value.
  26. :MEASure:TEMP?
    Query temperature.
  27. :FUNCtion<NRI>
    Set the current mode.
    :FUNC CC
    Parameters: { CC|CV|CR|CW|SHORt}
    Query syntax:
    :FUNC?
  28. :LIST
    Set LIST
    :LIST 4,3A,2,1A,0.1A/uS,5S,2A,0.1A/uS,5S,3
    Parameters:
    1. 4, Unit 4
    2. 3A, set the CC range to 3A
    3. 2, number of steps in LIST
    4. 1A, step 1 current 1A
    5. 0.1A/uS, slope of step 1
    6. 5s, time 5s for step 1
    7. 2A, the current 2A of step 2
    8. 0.1A/uS, slope of step 2
    9. 5s, time 5s for step 2
    10. 3, repeated execution times 3.
  29. :RCL:LIST<NR1>
    Recall the LIST unit.
    :RCL LIST 2
    Parameters: {1~7}
    Query syntax:
    :RCL:LIST?
  30. :OCP
    Set up OCP operations
    :OCP 2,15.0V,5.0S,3.0A,2.0A,0.1A,1.0S,1.0A,10.0V,1.5A,1.0A
    Parameters:
    1. 2, store 2 units
    2. 15V,VON 15V
    3. 5.0S,VON DELAY 5S
    4. 3.0A, current range 3A
    5. 2.0A, starting current 2.0A
    6. 0.1A, step current 0.1A
    7. 1.0S, step delay 1.0S
    8. 1.0A, cut-off current 1A
    9. 10.0V, OCP voltage 10V
    10. 1.5A, overcurrent max. 1.5A
    11. 1.0A, the minimum value of overcurrent is 1.0A
  31. :RCL:OCP<NR1>
    Recall OCP unit.
    :RCL OCP 2
    Parameters: {1~7}
    Query syntax:
    :RCL:OCP?
    Note: you need to recall first before querying.
  32. :OPP
    Set the OPP operation
    :OPP 2,15.0V,5.0S,3.0A,50W,1W,1S,10W,20V,30W,10W
    Parameters:
    1. 2, store 2 units
    2. 15V,VON 15V
    3. 5.0S,VON DELAY 5S
    4. 3.0A, current range 3A
    5. 2.0A, starting current 2.0A
    6. 0.1A, step current 0.1A
    7. 1.0S, step delay 1.0S
    8. 1.0A, cut-off current 1A
    9. 10.0V, OCP voltage 10V
    10. 1.5A, overcurrent max. 1.5A
    11. 1.0A, the minimum value of overcurrent is 1.0A
  33. :RCL:OCP<NR1>
    Recall OCP unit.
    :RCL OCP 2
    Parameters: {1~7}
    Query syntax:
    :RCL:OCP?
    Note: you need to recall first before querying.
  34. :BATTery
    Set up battery operation
    :BATT 2,30A,7A,35V,11AH,50M
    Parameters:
    1. 2, saved in unit 2 {1~7}
    2. 30A, battery range 30A
    3. 7A, the current starts at 7A
    4. 35V, discharge cut-off voltage 35V
    5. 11AH, discharge cut-off capacity 11AH
    6. 50M, discharge deadline 50 Minutes.
  35. :RCL:BATTery<NR1>
    Recall BATT unit 2.
    :RCL BATT 2
    Parameters: {1~7}
    Query syntax:
    :RCL:BATT?
    Note: you need to recall first before querying.
  36. :BATTery:TIM?
    Query the battery discharge time.
  37. :BATTery:CAP?
    Query the battery discharge capacity AH.
    Note: the above query commands only work in battery mode.
  38. :RCL:CURVe
    Set VI curve (VI):
    :CURVe 2,1.01A,2.02A,0.12A,5S
    Parameters:
    1. 2, cell {1~7 }
    2. 1.01A, starting current value
    3. 2.02A, ending current value
    4. 0.12A, step current value
    5. 5s, running time per step
  39. : RCL:CURVe<NRL>
    Recall VI curve 2 unit:
    :RCL:CURVe 2
    Query syntax:
    :RCL:CURVe?
  40. DYNamic
    Set Dynamics (CV):
    :DYN 1,1.0001V,2.0003V,1.101HZ,50.001%
    Parameters:
    1. 1,CV mode {1-CV;2-CC;3-CR;4-CW;5-PL;6-RL}
    2. 1.0001V, the first voltage value
    3. 2.0003V,the second voltage value
    4. 1.101HZ,switching frequency 1.101HZ
    5. 50.001%, duty cycle 50.001%
      Set dynamic (CC):
      :DYN 2,0.212A/uS,0.80A/uS,0.400A,2.10A,101.5HZ,46.00%
      Parameters:
      1. 2,CC mode {1-CV;2-CC;3-CR;4-CW;5-PL;6-RL}
      2. 0.212A/uS, rising slope
      3. 0.80A/uS, falling slope
      4. 0.400A, the first current value
      5. 2.10A, the second current value
      6. 101.5HZ, switching frequency 101.5HZ
      7. 46.00%, duty cycle 46.00%
        Set dynamic (CR):
        :DYN 3,1.0001OHM,2.0003OHM,2.0HZ,60.0%
        Set dynamic (CW):
        :DYN 4,3.2W,8W,1HZ,40.0%
        Set dynamic (RL):
        :DYN 2,0.212A/uS,0.80A/uS,0.400A,2.10A,101.5HZ,46.00%
        Set dynamic (PL):
        :DYN 5,0.15A/uS,0.20A/uS,1.2A,3.10A
  41. :RCL:DYNamic<NR1>
    Recall dynamic mode.
    :RCL:DYN 2
    Parameters: {1|CV,2|CC,3|CR,4|CW,5|PL,6|RL}
    Query syntax 1:
    :RCL:DYN?
    Query syntax 2:
    :DYN？
  42. :SYSTem:BAUD rate<NR1>
    Set baud rate.
    :SYST: BAUD 115200
    Parameters: {9600|19200|38400|57600|115200}
    Query syntax:
    : :SYST: BAUD?
  43. :SYSTem:IP ADdress<NR1>
    Set IP address.
    :SYST: IPAD 192.168.0.125
    Query syntax:
    : :SYST: IPAD?
  44. :SYSTem:SMASK<NR1>
    Set subnet mask.
    :SYST: SMASK 255.255.255.0
    Query syntax:
    : :SYST: SMASK?
    This command is used for setting the gate way.
    :SYST: GATE 192.168.0.1
    Query syntax:
    : :SYST: GATE?
  45. :SYSTem:PORT<NR1>
    Set IP communication ports.
    :SYST: PORT 18152
    Parameters: {100~65535}
    Query syntax:
    : :SYST: PORT?
    Note: the port can not be set to 18191.
  46. :SYSTem:RTC:YMD<YY,MM,DD>
    Set RTC year, month, day.
    :SYST: RTC:YMD 20,03,15
    Parameters: {YY,MM,DD}
    Query syntax:
    : :SYST: RTC:YMD?
  47. :SYSTem:RTC:HMS<hh,mm,ss>
    Query RTC hour, minute, second.
    :SYST: RTC:HMS 16,11,15
    Parameters: {hh,mm,ss}
    Query syntax:
    : :SYST: RTC:HMS?

Documents / Resources

KORAD KEL2000 Series Communication Protocol [pdf] User Guide
KEL2000 Series Communication Protocol, KEL2000 Series, Communication Protocol, Protocol

References

Related Posts

Leave a comment

Your email address will not be published. Required fields are marked *