Planet GPL-8000 8포트 GPON 광 회선 단말기 사용자 설명서

1. 서론

This manual provides comprehensive instructions for the installation, operation, and maintenance of the Planet GPL-8000 8-Port GPON Optical Line Terminal (OLT). The GPL-8000 is designed to facilitate high-speed fiber optic broadband network deployments, offering eight GPON ports, four Gigabit TP/SFP combo ports, four Gigabit SFP ports, four 10G SFP+ ports, and a dedicated management port. It complies with ITU-T G.984/G.988 standards, ensuring compatibility and reliable performance for connecting up to 1024 ONU and HGU devices.

2. 안전 정보

기기 손상을 방지하고 사용자의 안전을 확보하기 위해 다음 안전 수칙을 준수하십시오.

• 장치의 접지가 올바르게 되어 있는지 확인하세요.
• 기기를 물이나 과도한 습기에 노출시키지 마세요.
• 지정된 온도 및 습도 범위 내에서 장치를 작동하세요.
• 청소 또는 수리하기 전에 전원을 차단하십시오.
• Avoid looking directly into optical ports when active, as laser radiation can cause eye damage.
• Only use the power adapter provided or specified by the manufacturer.

3. 패키지 내용

패키지에 모든 품목이 들어 있는지 확인하세요.

• 1 x Planet 8-Port GPON Port Optical Line Terminal (GPL-8000)
• 전원 코드(지역에 따라 다를 수 있음)
• Rack-mounting Kit
• 빠른 설치 가이드

4. 제품 오버view

The Planet GPL-8000 is a robust Optical Line Terminal designed for high-density GPON deployments. Below is an illustration of the device's front panel, highlighting its various ports and indicators.

그림 1: Front Panel of the Planet GPL-8000 OLT. This image displays the front of the GPL-8000 unit, featuring a series of ports and LED indicators. From left to right, it includes power and system status LEDs, a console port, management (MGMT) ports, Gigabit TP/SFP combo ports (G1-G8), 10G SFP+ ports (TG1-TG4), and GPON ports (P1-P8). The Planet logo and model number GPL-8000 are visible on the right side.

4.1 전면 패널 구성 요소

• LED 표시등:
  • PWR1/PWR2: Power status indicators.
  • SYS : 시스템 상태 표시기.
  • 알람: 알람 표시기.
  • LNK/ACT (1G/10G): Link/Activity indicators for Gigabit and 10G ports.
  • PON (P1-P8): GPON port status indicators.
• 콘솔 포트: For local management access (RJ45).
• 관리 포트: Dedicated Ethernet port for out-of-band management.
• Gigabit TP/SFP Combo Ports (G1-G8): Four pairs of ports, each offering a Gigabit Ethernet (RJ45) and a Gigabit SFP slot. Only one interface in each combo pair can be active at a time.
• 10G SFP+ Ports (TG1-TG4): Four 10-Gigabit SFP+ slots for high-speed uplinks.
• GPON Ports (P1-P8): Eight GPON (Gigabit Passive Optical Network) ports for connecting to ONUs/HGUs.

5. 설정 및 설치

5.1 물리적 설치

1. 랙 장착: Secure the GPL-8000 into a standard 19-inch equipment rack using the provided rack-mounting kit. Ensure adequate ventilation around the unit.
2. 전원 연결: Connect the power cord to the device's power input and then to a grounded AC power outlet. Verify that the PWR LED illuminates.
3. 접지: Connect a grounding wire from the device's grounding screw to a proper earth ground.

5.2 초기 네트워크 연결

1. 관리 포트: Connect an Ethernet cable from your management workstation to the dedicated MGMT port on the GPL-8000.
2. 콘솔 포트(선택 사항): For direct command-line interface (CLI) access, connect a console cable from your workstation to the Console port. Configure your terminal emulator with settings: 9600 baud rate, 8 data bits, no parity, 1 stop bit (9600, N, 8, 1).
3. 업링크 연결: Connect your network's uplink cables to the 10G SFP+ ports (TG1-TG4) or the Gigabit TP/SFP Combo ports (G1-G8) as required.
4. GPON Connections: Insert appropriate GPON optical modules into the GPON ports (P1-P8) and connect the fiber optic cables to your GPON network.

6. 사용 설명서

6.1 Accessing the Device

The GPL-8000 can be managed via a web-based GUI, CLI (Console/Telnet/SSH), or SNMP.

• Web 그래픽 사용자 인터페이스: 열기 web browser and enter the device's IP address (default IP address can be found in the Quick Installation Guide or by using the console).
• CLI: Use a terminal emulator connected to the console port or establish a Telnet/SSH session to the device's IP address.

6.2 기본 구성

Refer to the detailed software user manual for advanced configuration. Key initial steps typically include:

• Changing the default administrator password.
• Configuring the management IP address.
• Setting up GPON service profiles and registering ONUs/HGUs.
• Configuring VLANs and QoS settings.

7. 유지관리

• 청소: Periodically clean the device's exterior with a soft, dry cloth. Ensure ventilation openings are free from dust and obstructions. Do not use liquid or aerosol cleaners.
• 펌웨어 업데이트: Regularly check the Planet website for firmware updates to ensure optimal performance and security. Follow the provided instructions for firmware upgrade procedures.
• 환경 모니터링: Ensure the operating environment remains within specified temperature and humidity limits to prevent hardware degradation.

8. 문제 해결

This section addresses common issues you might encounter with the GPL-8000.

• 전원 없음:
  • Verify the power cord is securely connected to both the device and the power outlet.
  • 전원 콘센트가 제대로 작동하는지 확인하세요.
  • Ensure the PWR LED is illuminated.
• 포트에 링크가 없습니다.
  • Check the cable connection for both ends.
  • Ensure the correct cable type is used (e.g., fiber for SFP/GPON, Ethernet for TP).
  • 연결된 장치의 전원이 켜져 있고 올바르게 작동하는지 확인하세요.
  • For SFP/SFP+ ports, ensure the correct transceiver module is inserted.
  • For GPON ports, check fiber integrity and ONU registration status.
• 접근할 수 없습니다 Web GUI/CLI:
  • Verify your management workstation's IP address is in the same subnet as the GPL-8000's management IP.
  • Check physical connection to the MGMT or Console port.
  • Ensure no firewall is blocking access.
  • Reset the device to factory defaults (refer to the full user manual for procedure) if the IP address is unknown or forgotten.

9. 사양

10. 보증 및 기술 지원

For detailed warranty information, please refer to the warranty card included with your product or visit the official Planet Technology Corporation website. For technical assistance, product documentation, or to report issues, please contact Planet's customer support through their official channels. Keep your product model number (GPL-8000) and serial number ready when seeking support.

제조업체: PLANET Technology Corporation.