KuWFi WiFi 6 AX1800 Outdoor Wireless AP Router (Model AP820) Instruction Manual

1. 서론

The KuWFi WiFi 6 AX1800 Outdoor Wireless AP Router (Model AP820) is an 11ax Wi-Fi standard outdoor access point designed to provide high-speed Ethernet data rates and allow more users access. It supports dual-band operation (2.4GHz and 5GHz) with a combined data rate of 1800Mbps. This device is suitable for extending Wi-Fi coverage in various environments, including homes, hotels, camping sites, factories, communities, and streets, thanks to its robust outdoor design and omnidirectional antennas.

2. 상자 안에 무엇이 들어있나요?

• 야외 WiFi 액세스 포인트
• Antennas (4 high-gain omnidirectional antennas)
• 네트워크 케이블
• 설치 패키지

3. 제품 오버view

The AP820 features a robust, weatherproof housing designed for outdoor use. It includes multiple ports and indicators for easy setup and monitoring.

3.1 장치 구성 요소

• 메인 유닛: The core device with internal components for Wi-Fi broadcasting and network management.
• 안테나 : Four high-gain omnidirectional antennas (two for 2.4GHz and two for 5GHz) for extended coverage.
• PoE Converter: An adapter that supplies power to the device through the Ethernet cable.
• 전원 어댑터: For connecting the PoE converter to a power outlet.

3.2 포트 및 표시등

• LAN 포트: For local network connections.
• PoE IN/WAN Port: Used for both Power over Ethernet input and Wide Area Network connection.
• 재설정 버튼: Located on the device for factory reset.
• 안테나 커넥터: Four connectors for attaching the omnidirectional antennas.

이미지: 하단 view of the KuWFi AP820 device, highlighting the LAN port, PoE IN/WAN port, and the Reset button. This view also shows the weather-sealed cap for cable entry.

4. 설정

4.1 안테나 설치

1. Identify the 2.4GHz and 5GHz antennas. The straight antennas are typically for 5GHz, and those with hinge points are for 2.4GHz.
2. Carefully screw each antenna into its corresponding port on the main unit. Ensure the rubber gaskets are properly seated for weatherproofing.

Image: A hand screwing one of the four antennas into the top of the KuWFi AP820 device, showing the secure connection point.

4.2 PoE(Power over Ethernet) 연결

1. Connect one end of the Ethernet cable to the PoE IN/WAN port on the AP820 unit. Ensure the weather-sealed cap is properly installed around the cable.
2. Connect the other end of the Ethernet cable to the PoE port on the PoE converter.
3. 전원 어댑터를 PoE 변환기에 연결한 다음 전원 콘센트에 꽂으세요.

4.3 초기 구성 (Web 상호 작용)

1. Connect your computer directly to the LAN port of the PoE converter using an Ethernet cable.
2. 열기 web browser and enter the default IP address (e.g., 192.168.188.253) or the domain name (e.g., wifi.wavlink.com) provided in the quick start guide to access the web 관리 인터페이스.
3. Follow the on-screen instructions to configure the device's operating mode (AP, Gateway, or Repeater), Wi-Fi settings (SSID, password), and other network parameters.

4.4 장치 장착

The AP820 can be mounted on a wall or pole using the provided installation package. Ensure the device is installed in a location that is not higher than 2-3 meters (6.562 to 9.843 feet) from the ground and not higher than the upstream router or subordinate devices by the same height range.

Image: Step-by-step diagram illustrating the physical installation of the KuWFi AP820 on a pole, including securing the device and routing the Ethernet cable.

4.5 Video Guide: Repeater Mode Setup

Video: A detailed guide demonstrating the setup process for the KuWFi AP820 in Repeater Mode. This video covers physical connections, web interface configuration, and testing the extended Wi-Fi signal.

5. 작동 모드

The KuWFi AP820 supports multiple operating modes to suit various networking needs:

• AP(액세스 포인트) 모드: Connects to a wired network and broadcasts a wireless signal, allowing wireless devices to connect to the network.
• 게이트웨이 모드: Functions as a router, providing network address translation (NAT) and managing the local network.
• 리피터 모드: Extends the range of an existing wireless network by receiving and re-transmitting the Wi-Fi signal.

이미지: 항공 사진 view illustrating the KuWFi AP820 in AP/Gateway mode, providing seamless Wi-Fi coverage across a large outdoor area with multiple access points.

6. 유지관리

• Regularly check the device for any physical damage or loose connections, especially after severe weather conditions.
• Ensure the weather-sealed caps on the ports are securely fastened to prevent water ingress.
• Keep the device's firmware updated to ensure optimal performance and security. Refer to the manufacturer's web최신 펌웨어 버전 및 업데이트 지침을 확인할 수 있는 사이트입니다.
• Clean the exterior of the device periodically with a soft, dry cloth to remove dust and debris.

7. 문제 해결

• 전원 없음: Check the power adapter and PoE converter connections. Ensure the power outlet is functional.
• Wi-Fi 신호 없음: Verify that the antennas are correctly installed and tightened. Check the device's operating mode and Wi-Fi settings in the web 인터페이스.
• 약한 신호 강도: Adjust the device's placement to minimize obstructions. Ensure antennas are oriented correctly. Consider using Repeater Mode if extending coverage over a large area.
• 접근할 수 없습니다 Web 인터페이스: Ensure your computer is directly connected to the PoE converter's LAN port. Verify your computer's IP settings are compatible with the device's default IP range. Try resetting the device to factory defaults using the Reset button.
• 간헐적인 연결: Check for interference from other wireless devices or electrical equipment. Ensure the Ethernet cable length does not exceed 60 meters (196 feet) to prevent power loss over PoE.

8. 사양

9. 보증 및 지원

The KuWFi WiFi 6 AX1800 Outdoor Wireless AP Router (Model AP820) is backed by a 30-day money-back guarantee, a month free replacement, and a 1-year manufacturer warranty. Professional technical support is available.

For setup problems or additional instructions, please download the KuWFi shared file containing operation steps and instructions from: https://drive.google.com/drive/folders/12kkvlLpuiQRLtOU60tNDwwl8XFeRIEPJ?usp=sharing

9.1 Video Guide: Product Overview

비디오: 간략하게 살펴보기view of the KuWFi AP820 wireless AP router, showcasin그 특징과 구성 요소를 살펴보겠습니다.