소개
This manual provides detailed instructions for the installation, operation, and maintenance of the Bogen AT10A 10-Watt Attenuator. The AT10A is designed to control the volume of individual speakers or groups of speakers in a constant voltage (70V or 25V) audio distribution system.
Please read this manual thoroughly before installation and operation to ensure proper use and to prevent damage to the unit or connected equipment.
제품 끝view
이미지: 앞면 view of the Bogen AT10A 10-Watt Attenuator. The unit features a silver faceplate with a black rotary volume knob. The knob is marked with numbers from 0 to 10, indicating volume levels. The Bogen logo is visible at the bottom center, and "AT-10A" is printed in the bottom right corner.
The Bogen AT10A is a wall-plate style attenuator, providing 10 steps of volume control plus an "OFF" position. It is suitable for use with 25V or 70V constant voltage speaker lines and has a power rating of 10 watts.
설정 및 설치
안전 예방 조치
- 설치를 시작하기 전에 오디오 시스템의 모든 전원을 차단하십시오.
- 설치는 해당 지역의 전기 규정에 따라 자격을 갖춘 인력이 수행해야 합니다.
- Do not exceed the maximum power rating of 10 watts.
설치
- The AT10A is designed to fit into a standard single-gang electrical box.
- Secure the electrical box in the desired wall location.
- Ensure adequate space for wiring connections behind the attenuator.
배선 연결
The AT10A features screw terminals for input and output connections. Refer to the diagram below for typical wiring.
- 상수 볼륨을 연결tage audio source (e.g., amplifier output) to the "INPUT" terminals.
- Connect the speaker(s) to be controlled to the "OUTPUT" terminals.
- Maintain correct polarity (+ to + and - to -) for all connections.
- 모든 연결이 안전하고 단락이 없는지 확인하세요.
(Note: A detailed wiring diagram would typically be provided here by the manufacturer. For this manual, general instructions are given.)
작동 지침
The Bogen AT10A provides simple rotary control for adjusting the volume level of connected speakers.
- 전원 켜기: After installation, restore power to the audio system.
- 볼륨 조절: Rotate the knob clockwise to increase the volume and counter-clockwise to decrease it.
- 볼륨 레벨: The knob features marked positions from 0 to 10. Position '0' represents the "OFF" or minimum volume setting, while '10' represents the maximum volume setting.
- 미세 조정: Adjust the knob gradually to achieve the desired listening level.
유지
The Bogen AT10A is designed for reliable, long-term operation with minimal maintenance.
- 청소: To clean the faceplate, gently wipe with a soft, dry cloth. Do not use abrasive cleaners or solvents.
- 점검: Periodically check the attenuator for any visible damage or loose connections. If any issues are found, disconnect power and address them promptly.
- 사용자가 수리할 수 없는 부품: The internal components of the AT10A are not user-serviceable. Do not attempt to open or repair the unit. Refer servicing to qualified personnel.
문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 스피커에서 소리가 나지 않습니다. |
|
|
| Distorted or low-quality sound. |
|
|
If troubleshooting steps do not resolve the issue, contact Bogen technical support or a qualified audio technician.
명세서
| 특징 | 세부 사항 |
|---|---|
| 모델 | AT10A |
| 전력 정격 | 10 와트 |
| 권tag전자 호환성 | 25V / 70V 정전압tag전자 시스템 |
| 볼륨 단계 | 10 steps plus "OFF" |
| 설치 | 싱글 갱 전기 박스 |
| 치수(패키지) | 9.49 x 8.39 x 3.94 인치 |
| 품목 무게 | 1.2파운드 |
| ASIN | B01IE047U6 |
| 한국어: | 080850445046 |
| 첫 번째 이용 가능 날짜 | 13년 2016월 XNUMX일 |
지원 및 연락처 정보
For technical assistance, product inquiries, or further information, please contact Bogen Communications, Inc.
- 제조업체: Bogen Communications, Inc.
- Web대지: www.bogen.com (전amp(링크는 실제 링크와 다를 수 있습니다)
- 고객 서비스: Refer to the official Bogen web최신 연락처 정보는 사이트에서 확인하세요.
참고: 제품 사양은 예고 없이 변경될 수 있습니다.
