중요 안전 지침
Before operating the Generac 6922 pressure washer, read and understand all safety warnings and instructions in this manual. Failure to follow these instructions may result in serious injury or property damage.
- 눈 보호 장비, 청력 보호 장비, 보호 신발 등 항상 적절한 개인 보호 장비를 착용하세요.
- 분무기를 사람, 애완동물 또는 전자 기기에 직접 조준하지 마십시오. 고압 분사로 심각한 부상을 입을 수 있습니다.
- Ensure all connections are secure before starting the unit to prevent leaks and loss of pressure.
- Operate the pressure washer in a well-ventilated area to avoid carbon monoxide poisoning from engine exhaust.
- Do not operate the unit if any parts are damaged or missing. Contact Generac customer support for replacement parts.
- 어린이와 주변인이 작업 영역에 접근하지 못하도록 하십시오.
- Use only approved fuels and oils as specified in this manual. Store fuel in approved containers and away from ignition sources.
- Always engage the spray gun trigger safety lock when not spraying to prevent accidental discharge.
제품 끝view
The Generac 6922 is a gas-powered pressure washer designed for medium-duty residential cleaning tasks. It delivers 2800 PSI and 2.4 GPM, making it suitable for cleaning decks, siding, driveways, and vehicles. Key features include an ergonomic spray gun, integrated detergent tank, and quick-change nozzle tips.

그림 1: 전면 view of the Generac 6922 Gas Powered Pressure Washer.
주요 구성 요소
- 엔진: Generac OHV horizontal-shaft engine provides reliable power.
- 펌프: Delivers high-pressure water for effective cleaning.
- 분무기: Ergonomic design with cushion grip and easy-to-pull trigger for reduced fatigue.
- 고압 호스: 25-foot hose for extended reach.
- 노즐 팁: Includes 0-degree, 25-degree, 40-degree, and soap nozzles for various applications.
- 세제 탱크: Integrated 0.5-gallon tank for convenient on-board detergent storage.
- 바퀴: 10-inch never-flat wheels for easy maneuverability across different terrains.
- 제어판: User-friendly controls for on/off, choke, and fuel shutoff.

그림 2: 전면 view of the pressure washer, showing the control panel and spray gun holder.

그림 3: 측면 view of the pressure washer, highlighting the engine and pump assembly.

그림 4: 후면 view of the pressure washer, showing the hose connection point.

Figure 5: Close-up of the integrated hose storage on the handle.

Figure 6: Close-up of the Generac OHV engine, showing the fuel cap and pull start.

Figure 7: Close-up of the integrated 0.5-gallon detergent tank.

Figure 8: Close-up of the pump connections, including the water inlet and high-pressure outlet.
설정 및 조립
1. 풀기
Carefully remove all components from the packaging. Inspect for any damage during shipping. Ensure all parts listed in the packing list are present.
2. 핸들 조립
- Slide the upper handle assembly onto the lower frame until the spring buttons engage.
- Secure the handle with the provided knobs or bolts, ensuring it is firmly in place.
3. Connecting the Spray Gun and Hose
- Connect the high-pressure hose to the pump outlet. Tighten securely, preferably with a wrench to prevent leaks.
- 고압 호스의 다른 쪽 끝을 스프레이 건에 연결하세요. 단단히 연결되었는지 확인하세요.
- Insert the desired quick-change nozzle tip into the spray gun wand until it clicks into place.
4. 엔진 오일 추가
The engine may be shipped without oil. Refer to the engine manual for specific oil type and capacity. Typically, 10W-30 oil is recommended. Do not overfill.
- 압력 와셔를 평평한 표면에 놓습니다.
- 오일 주입 캡/딥스틱을 제거합니다.
- Slowly add the recommended engine oil until it reaches the full mark on the dipstick.
- 엔진 오일 주입구 캡/오일 레벨 게이지를 제자리에 다시 끼우십시오.
5. 연료 추가
Use fresh, unleaded gasoline with an octane rating of 87 or higher. Do not use E85 fuel. Always add fuel in a well-ventilated area away from ignition sources.
- 엔진이 꺼져 있고 식었는지 확인하세요.
- 연료 캡을 제거하세요.
- Fill the fuel tank, leaving some space for expansion. Do not overfill.
- 연료 캡을 단단히 닫으세요.
6. 물 공급 연결
Connect a standard garden hose to the water inlet on the pump. Ensure the garden hose is free of kinks and has sufficient flow. Turn on the water supply completely before starting the engine.
작업
1. Pre-Start Checklist
- 엔진 오일 레벨을 확인하세요.
- 연료 수준을 확인하세요.
- 물 공급 장치가 연결되어 있고 켜져 있는지 확인하십시오.
- Select and install the appropriate nozzle.
- 모든 호스 연결이 단단히 조여져 있는지 확인하십시오.
2. 엔진 시동
- 연료 밸브를 여십시오(장착된 경우).
- Move the choke lever to the 'CHOKE' position (cold engine).
- 엔진 스위치를 'ON'으로 설정합니다.
- 엔진이 시동될 때까지 스타터 로프를 단단히 당깁니다.
- 엔진이 시동되면 초크 레버를 점차 'RUN' 위치로 옮기세요.
- Allow the engine to warm up for a few moments.
3. 세제 사용
The integrated 0.5-gallon detergent tank allows for easy application of cleaning solutions.
- Fill the detergent tank with pressure washer safe detergent.
- Install the black soap nozzle onto the spray gun. This nozzle activates the detergent injector.
- Spray the detergent onto the surface to be cleaned. Allow it to soak for a few minutes (do not let it dry).
- Switch to a high-pressure nozzle (e.g., 25-degree) to rinse the surface thoroughly.
4. 노즐 선택
The Generac 6922 includes four quick-change nozzle tips:
- 0-degree (Red): 정밀한 분사로 작고 stubborn한 얼룩까지 깨끗하게 세척합니다. 사용 시 각별한 주의를 기울이십시오.
- 25-degree (Green): 팬 스프레이는 대부분의 표면을 청소하는 데 적합합니다.
- 40-degree (White): Wide fan spray for gentle cleaning of delicate surfaces.
- 비누(검정색): Low-pressure stream for applying detergents.
5. 청소 절차
- Always start spraying with the nozzle a safe distance from the surface and move closer as needed.
- Use overlapping strokes to ensure even cleaning.
- Work from top to bottom when cleaning vertical surfaces to prevent streaking.
6. 종료
- If using detergent, flush the system with clean water by running the pressure washer with the soap nozzle in a bucket of clean water until all detergent is cleared.
- 엔진 스위치를 끕니다.
- 물 공급을 차단하세요.
- 스프레이 건 방아쇠를 당겨 시스템에 남아 있는 압력을 방출하세요.
- 정원 호스와 고압 호스를 분리합니다.
유지
Regular maintenance ensures optimal performance and extends the life of your pressure washer. Always perform maintenance with the engine off and cool, and the spark plug wire disconnected.
1. 엔진 오일 교환
Change the engine oil after the first 5 hours of operation, then every 50 hours or annually, whichever comes first. Refer to the engine manual for detailed instructions.
2. 공기 필터 청소/교체
Inspect the air filter regularly and clean or replace it as needed, especially in dusty conditions. A dirty air filter can reduce engine performance.
3. 점화 플러그 검사
Inspect the spark plug annually or every 100 hours. Clean or replace if fouled or damaged. Ensure proper gap setting.
4. 펌프 유지관리
After each use, flush the pump with clean water. For extended storage, use a pump protector to prevent freezing and corrosion.
5. 보관
Before storing the pressure washer for an extended period:
- Drain all fuel from the tank or add a fuel stabilizer.
- 기화기를 배출합니다.
- 엔진 오일을 교체하세요.
- Apply pump protector.
- Store in a clean, dry, and frost-free area.
문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 엔진이 시동되지 않습니다 | No fuel; Engine switch OFF; Choke incorrect; Spark plug issue; Low oil shutdown | Add fuel; Turn switch ON; Adjust choke; Inspect/replace spark plug; Check oil level |
| 압력이 낮거나 없음 | Water supply off/restricted; Air in pump; Clogged nozzle; Detergent nozzle in use | Turn on water, check hose; Purge air from pump; Clean/replace nozzle; Switch to high-pressure nozzle |
| 맥동 스프레이 | 펌프에 공기가 들어감; 물 공급이 제한됨; 노즐이 막힘 | Purge air; Check water supply/hose; Clean nozzle |
| 세제가 잘 안 빠짐 | Detergent tank empty; Clogged detergent line; Wrong nozzle in use | Fill tank; Clean line; Use black soap nozzle |
| 물 누출 | 연결 부위가 헐거워짐; O링/씰 손상 | Tighten connections; Inspect/replace O-rings/seals |
기술 사양
| 사양 | 값 |
|---|---|
| 상표 | 제네락 |
| 모델 번호 | 6922 |
| 전원 | 가스 구동 |
| 최대 압력 | 2800파운드 |
| 최대 유량 | 분당 2.4갤런(GPM) |
| 호스 길이 | 25 피트 |
| 세제 탱크 용량 | 0.5갤런 |
| 품목 무게 | 57 파운드 |
| 제품 치수 | 24.4 x 18.8 x 35.4 인치 |
| 한국어: | 696471069228 |
보증 정보
This Generac pressure washer is covered by a manufacturer's limited warranty. For specific details regarding warranty coverage, duration, and terms, please refer to the warranty card included with your product or visit the official Generac web사이트. 보증 청구를 위해 구매 증빙 자료를 보관하세요.
고객 지원
For technical assistance, replacement parts, or service inquiries, please contact Generac customer support. You can find contact information on the Generac website or in the documentation provided with your pressure washer. Have your model number (6922) and serial number ready when contacting support.





