1. 제품 오버view
The Schlage F51A Georgian 505 is a single cylinder entry door lock knobset designed for residential use. This lock provides security with a key entry from the outside and a turn-button for locking/unlocking from the inside. The interior knob always remains free for immediate exit (panic-proof function). The unit is non-handed and field reversible, allowing for flexible installation on left or right-handed doors.
2. 패키지 내용
설치를 시작하기 전에 모든 구성품이 있는지 확인하십시오. 부품이 누락되었거나 손상된 경우 설치를 진행하지 말고 고객 지원팀에 문의하십시오.
- Exterior Knob Assembly (with key cylinder)
- Interior Knob Assembly (with turn-button)
- Latch Bolt Assembly
- Strike Plate (Part 10-063, supplied with Square Corner and Round Corner Full Lip Strike Plates, Dimensions: 2-1/4" x 1-5/8")
- Faceplates (Part 16-211, supplied with 1/4" Round Corner, Square Corner and Drive-In Faceplates)
- 장착 나사
- 키 (일반적으로 2개)
- 설치 템플릿(포함된 경우)
3. 안전 정보
설치 및 사용 전에 모든 지침을 주의 깊게 읽으십시오. 나중에 참조할 수 있도록 이 설명서를 보관하십시오.
- 설치 작업 중에는 항상 보안경과 같은 적절한 안전 장비를 착용하십시오.
- Use the correct tools for the job to prevent damage to the lock or injury.
- Ensure the door is properly prepared and aligned before installing the lock.
- Do not force components during installation. If parts do not fit, re-check the instructions.
- 질식 위험을 방지하려면 작은 부품을 어린이의 손이 닿지 않는 곳에 보관하십시오.
- 중요한: Do not use prints made from this website or any digital source to mark distances for drilling. Due to individual printers and display settings, dimensions on installation instructions may not print or display at an accurate scale. Always use the physical template provided with the product or measure carefully.
4. 설치 가이드
This section provides general steps for installing the Schlage F51A Georgian 505 entry door lock. For detailed, step-by-step instructions, refer to the specific installation template and guide included in your product packaging.
4.1 문 준비하기
- Ensure the door is properly bored for a standard door lock (typically 2-1/8 inch cross bore and 1 inch edge bore).
- Measure the backset (distance from the door edge to the center of the cross bore). Adjust the latch bolt if necessary to fit 2-3/8 inch or 2-3/4 inch backsets.
- Chisel out a mortise for the latch faceplate and strike plate on the door edge and frame, respectively, if not already present.
4.2 Install the Latch Bolt
- Insert the latch bolt into the edge bore of the door, ensuring the bevel of the latch faces the door frame.
- Secure the latch bolt with the provided screws. Choose the appropriate faceplate (1/4" Round Corner, Square Corner, or Drive-In) to match your door preparation.
4.3 Install the Knobs
- Insert the exterior knob assembly through the cross bore, ensuring the spindle engages with the latch mechanism.
- Place the interior knob assembly onto the spindle, aligning the mounting posts with the holes in the exterior assembly.
- Secure the interior and exterior assemblies together using the provided mounting screws. Tighten screws evenly to prevent binding.
- 메모: The unit is non-handed and field reversible, meaning it can be installed on either left or right-handed doors without modification.
4.4 Install the Strike Plate
- Close the door and mark the position where the latch bolt strikes the door frame.
- Install the strike plate (Part 10-063) on the door frame, aligning it with the latch bolt. Use the appropriate strike plate (Square Corner or Round Corner Full Lip) for your frame.
- Secure the strike plate with the provided screws.
4.5 테스트 작동
After installation, test the lock's function with the door open and closed to ensure smooth operation.
5. 운영
5.1 Locking and Unlocking from the Exterior
- To unlock: Insert the key into the keyway and turn it.
- To lock: Turn the key to the locked position and remove it. The exterior knob will then be rigid.
5.2 Locking and Unlocking from the Interior
- To unlock: Rotate the turn-button on the interior knob.
- To lock: Rotate the turn-button on the interior knob to the locked position.
- Panic-Proof Feature: The interior knob always remains free, allowing for immediate exit even when the lock is engaged. Turning the interior knob will retract the latch bolt.
6. 유지관리
Proper maintenance ensures the longevity and smooth operation of your Schlage lock.
- 청소: 부드러운 천으로 잠금장치 외부를 청소하세요.amp 천으로 닦으세요. 연마성 세제, 용제 또는 강한 화학 물질은 마감재를 손상시킬 수 있으므로 피하세요.
- 매끄럽게 하기: Periodically apply a small amount of graphite-based lubricant (do not use oil-based lubricants) into the keyway and the latch mechanism to ensure smooth operation.
- 점검: Regularly check all mounting screws for tightness. If the lock feels loose, gently tighten the screws.
- 마무리 관리 : The Lifetime Bright Brass finish is designed for durability. However, prolonged exposure to harsh weather or chemicals can affect its appearance.
7. 문제 해결
If you encounter issues with your Schlage F51A Georgian 505 lock, refer to the following common problems and solutions:
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 열쇠가 돌아가지 않거나 뻑뻑합니다. | Dirt in keyway, worn key, or misaligned cylinder. | Clean keyway with compressed air. Apply graphite lubricant. Try a spare key. If issue persists, contact support. |
| 손잡이가 헐거워지거나 흔들거립니다. | 장착 나사가 느슨합니다. | Tighten the mounting screws on the interior knob assembly. |
| Latch bolt does not retract fully or binds. | Misalignment of lock components or strike plate. | Check alignment of latch bolt and strike plate. Ensure mounting screws are not overtightened, causing binding. Lubricate latch mechanism. |
| 문이 제대로 잠기지 않거나 닫히지 않습니다. | 스트라이크 플레이트 정렬 불량 또는 문 처짐. | Adjust the strike plate position on the door frame. Check door hinges for sag. |
8. 사양
- 모델 번호: F51A GEO 505
- 상표: 슐라게
- 유형: Single Cylinder Entry Door Lock Knobset
- 마치다: Lifetime Bright Brass
- 재료: 놋쇠
- 스타일: Traditional (Georgian)
- 특별 기능: Key Lock, Panic-Proof Interior Knob
- 제품 크기: 약 4 x 6 x 5인치
- 품목 무게: 약 1.2파운드
- 필요한 배터리: 아니요
- 원산지: 멕시코
9. 보증 및 지원
Schlage products are backed by a manufacturer's warranty. For specific warranty details, please refer to the warranty information included with your product packaging or visit the official Schlage web대지.
If you require technical assistance, have questions about installation, or need to report a missing/damaged part, please contact Schlage Customer Support. Contact information can typically be found on the Schlage web사이트나 제품 설명서에서 확인하세요.
온라인 리소스: www.schlage.com
