1. 서론
This manual provides essential information for the safe and efficient operation of your Clover B7A Hot and Cold Water Dispenser. Please read all instructions carefully before installation and use. This high-quality water cooler is designed to provide refreshing chilled drinking water or piping hot water for various uses in your home or office.
이미지: 앞면 view of the Clover B7A Hot and Cold Water Dispenser with a 5-gallon water bottle installed on top. The dispenser is white with red and blue spigots for hot and cold water, respectively.
2. 안전 정보
- 디스펜서는 항상 안정적이고 평평한 표면에 놓아야 합니다.
- 분배기를 직사광선과 열원으로부터 멀리 두십시오.
- 장치 주변의 적절한 환기를 확인하십시오.
- The hot water spigot features a child safety lock. To dispense hot water, you must engage the safety mechanism before pressing the lever.
- Do not plug in the unit until a water bottle is properly installed and water has filled the internal tanks.
- 청소나 유지관리를 하기 전에는 분배기의 플러그를 뽑으세요.
3. 설정 및 설치
- 짐 풀기: 디스펜서를 포장에서 조심스럽게 꺼내세요. 손상 여부를 확인하세요.
- 놓기: Position the dispenser on a flat, sturdy surface near a grounded electrical outlet. Ensure there is adequate space around the unit for ventilation.
- 청소: Before first use, wipe down the exterior of the dispenser with a soft, damp cloth. Clean the removable drip tray.
- 물병 설치:
- 일반적인 5갤런짜리 물병에서 보호 씰을 제거하세요.
- Carefully invert the water bottle and place it firmly onto the bottle support collar at the top of the dispenser. Ensure the bottle is seated correctly and the probe pierces the bottle cap.
- Wait a few minutes for the internal tanks to fill with water. You may hear bubbling sounds as the tanks fill.
- 전원 연결: Once the water tanks are filled (bubbling stops), plug the power cord into a grounded 110-120 volt electrical outlet.
- 난방/냉방 활성화: Locate the power switches for hot and cold water on the back of the unit. Flip them to the 'ON' position to activate the heating and cooling functions. Allow approximately 15-30 minutes for the water to reach optimal temperatures.
4. 사용 설명서
- 냉수 분배: Place your cup under the blue spigot. Push the blue lever to dispense chilled water.
- 뜨거운 물 분배: Place your cup under the red spigot. Engage the child safety lock (usually by sliding a button or pressing a tab) and then push the red lever to dispense hot water. Exercise caution as the water is very hot (approximately 185°F).
- Adjustable Cold Water Thermostat: The cold water temperature can be adjusted between 35.6°F and 53.6°F using the thermostat control located on the back of the unit.
5. 특징
- Stainless Steel Tanks: Both hot and cold water tanks are constructed of hygienic stainless steel, designed for contaminant resistance and health protection.
- 온도 조절: Cold water temperature is adjustable (35.6°F-53.6°F). Hot water temperature is automatically controlled to approximately 185°F (non-adjustable).
- 에너지 스타 등급: Meets strict energy-efficiency guidelines set by the EPA and U.S. Department of Energy.
- Efficient Heating and Cooling: Features an ultra-efficient condenser cooled via convection, operating quietly.
- Durable Faucets: Equipped with durable polypropylene, self-closing spigots.
- 이동식 드립 트레이: One-piece ABS drip tray is removable for easy cleaning.
- Safety Float Mechanism: Double float valve with secondary safety float mechanism helps reduce water loss from spilling.
6. 유지관리 및 청소
- 외부 청소: 외부 표면은 부드러운 천으로 정기적으로 닦아주세요.amp 옷감. 연마성 세제를 피하십시오.
- 물받이 청소: The removable drip tray should be emptied and cleaned regularly (e.g., weekly or bi-weekly, depending on usage) to prevent water overflow and maintain hygiene. Simply pull it out, empty, wash with mild soap and water, rinse, and snap back into place.
- 석회질 제거 : Over time, mineral deposits may accumulate, especially in the hot water tank, potentially slowing water flow. The manufacturer recommends descaling the unit periodically. Refer to general descaling instructions for water dispensers or coffee makers, using appropriate descaling solutions. Always unplug the unit and drain all water before descaling.
7. 문제 해결
- 온수/냉수 안 나옴:
- Check if the hot/cold power switches on the back of the unit are in the 'ON' position.
- Ensure the unit is plugged into a working electrical outlet.
- Verify that the water bottle is not empty and is properly seated.
- Allow sufficient time (15-30 minutes) for the water to heat or cool after initial setup or bottle change.
- 물의 흐름이 느림:
- Ensure the water bottle is not empty.
- Mineral buildup can restrict water flow, especially for hot water. Refer to the descaling instructions in the Maintenance section.
- 물 누출:
- Check if the water bottle is properly seated on the dispenser.
- Inspect the water bottle for cracks or damage.
- Ensure the drip tray is correctly installed and not overflowing.
8. 사양
| 특징 | 세부 사항 |
|---|---|
| 모델 | 비7A |
| 제품 유형 | 냉온수 디스펜서 |
| 치수(길이 x 너비 x 높이) | 14.00인치 x 12.40인치 x 37.80인치 |
| 무게 | 33.00파운드(품목 무게: 31.6파운드) |
| 색상 | 하얀색 |
| 애플리케이션 | Dispenses hot and cold water in home or office |
| 권tage | 110-120 볼트 |
| 빈도 | 50-60Hz |
| 인증 | CE, NSF, UL |
| 유형 | Bottled (Top-loading) |
| 물 온도 | 뜨겁고 차갑다 |
| Hot Water Thermostat Temp. Range | Automatically controlled to nearly 185°F (non-adjustable) |
| Cold Water Thermostat Temp. Range | Adjustable from 35.6-53.6°F |
| 수도꼭지 유형 | Durable polypropylene, self-closing spigots |
| 에너지 스타 등급 | 예 |
| Drip Tray Type | Removable one-piece ABS drip tray |
| 호환되는 병 크기 | 5갤런 |
| 내장형 필터 시스템 | 아니요 |
| 재료 | Polyethylene (PE), Polypropylene (PP), Stainless Steel |
9. 보증 및 지원
The Clover B7A Hot and Cold Water Dispenser comes with a 1년 제한적 제조사 보증.
For technical support, warranty claims, or further assistance, please contact CLOVER customer service. Refer to the product packaging or the official CLOVER web최신 연락처 정보는 사이트에서 확인하세요.
