HP 331011867-01 GPU Computing Processor Installation Guide

HP 331011867-01 GPU Computing Processor

명세서

• 모델: NVIDIA Tesla P100 16GB
• 메모리: 16GB 메모리
• 다음을 위해 설계되었습니다: Professional computing tasks (deep learning, scientific computing, rendering)
• 적합하지 않은 경우: Gaming, video playback acceleration
• 전력 요구 사항: Minimum 500W PSU recommended
• 인터페이스: PCIe 3.0 x16
• 비디오 출력: None (compute-only GPU)

Safety Warnings & Pre-Installation Notes

This is a used professional computing GPU with NO video output ports. It is not intended for consumer gaming use and is designed for server/workstation environments only. Please read carefully before installation:

• TDP: 250W. Requires a power supply rated ≥500W with a standard 8-pin (or 6+2-pin) PCIe power connector.
• Only supports PCIe 3.0 x16 slots. Motherboard must support UEFI mode and Above 4G Decoding.
• Passive cooling design: Must be installed in a server chassis with forced airflow. Insufficient cooling will cause thermal throttling or hardware damage.
• No display output: A separate GPU or motherboard iGPU is required for system display.

하드웨어 설치 단계

1단계: 준비

1. Shut down the host, disconnect the power cord, and discharge static electricity by touching the metal chassis.
2. Remove the side panel and locate the PCIe 3.0 x16 slot (preferably the one closest to the CPU).
3. Remove the corresponding PCIe bracket from the chassis (requires a 2-slot wide clearance).

Step 2: Install the GPU

1. Hold the card by its edges, align it with the PCIe slot’s key notch, and press down evenly until you hear a “click” (indicating it is locked).
2. Secure the GPU bracket to the chassis with screws to prevent movement.
3. Connect the 8-pin power cable: Fully insert the power supply’s 8-pin (or 6+2-pin) connector into the GPU’s power port and confirm it is firmly seated.

Step 3: Chassis & Cooling Check

1. Ensure there is no obstruction around the GPU and that the chassis airflow is unobstructed (front-to-back airflow is recommended).
2. After installation, verify the GPU is fully seated in the slot and the power cable is not stretched or blocked.

Critical BIOS Configuration

Power on and press the BIOS key (Del/F2/F10, depending on your motherboard brand):

1. Navigate to PCIe/PCI/PnP Configuration and enable Above 4G Decoding (required for proper addressing of large memory).
2. Disable CSM Support(Compatibility Support Module) and set the boot mode to pure UEFI.
3.  Set PCIe Speed to Gen3(or Auto) and disable PCIe ASPM power-saving options.
4. Save changes and restart the computer.

System Driver Installation & Configuration

윈도우 시스템 설정

1. System Requirements: Windows 10/11 64-bit Professional/Enterprise Edition (Home Edition is not recommended).
2. Download and install the latest NVIDIA Tesla drivers from the official NVIDIA website, selecting the “Data Center/Tesla” branch.
3. After installation, open NVIDIA Control Panel → Manage GPU Utilization to confirm the card is detected.

Linux System Setup

1. System Requirements: Ubuntu 18.04/20.04 LTS or CentOS 7/8 (kernel 4.15+ recommended).
2. Disable the default Nouveau driver, then install the official NVIDIA driver and CUDA toolkit.
3. Verify installation with the command: nvidia-smi(the Tesla P100 16GB should appear in the list).

일반적인 문제 해결

최종 노트

• This GPU is designed for computing tasks only (deep learning, scientific computing, rendering). It does not support gaming or video playback acceleration.
• Keep the GPU in a well-ventilated environment to ensure long-term stability.
• If you encounter any issues during installation, please contact us before returning the item.