សៀវភៅណែនាំអ្នកប្រើប្រាស់ Woowind AP2-2 Smart Tire Inflator
Smart Tire Inflater
Thank you for purchasing the Smart Tire Pump. Please read this user manual carefully before using this product, and keep it for future reference.
1 . Accessories list
2.Speciflcation
១.២. ផលិតផល
4. ព្រមាន៖
កុំចាកចេញក្នុងអំឡុងពេលអតិផរណា។
Do not place the product near flammable and explosive products.
Avoid moisture,sand and prevent from falling.
Do not store the product in a cold or hot place.
It is forbidden to throw the product into fire or throw it away at will.
មិនមែនសម្រាប់កុមារទេ។
5.Use instructions:
5.1 Charging and Power Bank mode
- Use the power adapter (not included) and the Type-C charging cable to charge.
Charging: battery indicator flashes.
Full battery status: all battery indicator lights are always on.
After 10 seconds of no operation during charging, the display will automatically turn off.
ផលិតផលមិនអាចប្រើកំឡុងពេលសាកថ្មបានទេ។
Charging: battery indicator flashes. - Long press the power button [6] to turn it on, the USS port [4] can supply power to charge other electronic products. USB output 5V /1 5A (Max). The machine will turn off automatically after the power off. After the electronic equipment is fully charged, It will turn off automatically.
5.2 បើក/បិទថាមពល
*Long press power button for 3 seconds and the progress bar starts to launch for power on.
* Long press power button for 3 seconds and wait for progress bar backward complete to power off.
* It will automatically shut down after 3 minutes when there is no operation.
*Automatic shutdown when battery is low
5.3 ការប្តូររបៀប
Short press the scene switch key, you can select 5 scene modes, namely:
Short press button +/- ([9]/[10]) to adjust preset pressure value [16].
Long press button +/- ([9]/[1 0]) to rapidly adjust preset pressure value [16].
Long press button [B] to turn on/off LED light
Short press power button [6]to accurate the Reset, real-time pressure value changes during inflation and noise cannot be avoid.
The hose will be heated after long time working. Avoid touching it and the joint with your hands for a long time.
Notice: The mode mode and preset pressure value will be automatically saved when the machine is turned off, and the last preset pressure value will be automatically restored until next use.
5.5 Hose connection method
The hose connection is shown in the figure below:
5.6 Air pressure detection and inflation
Short press power button[6] to stop inflation. When the air pressure reaches the preset pressure value, the pump automatically stops inflation. After turning on, connect the hose to the object to be measured, measured pressure [12] shows current pressure value.
5.7 ការក្រិតតាមខ្នាតសម្ពាធ
After turning on, when the measured pressure value is not 0, press button [9] and [1 O] for 2 seconds to enter reset, the display flashes quickly means the reset is complete.
Notice: the product has been reset at the factory. Due to altitude differences, reset can improve the accuracy of the air pressure. Do not connect inflatable objects when reseting.
6. ការប្រុងប្រយ័ត្នសុវត្ថិភាព
When unscrewing the hose, the hose and joint [1] will be heated due to long-term work, so please do not touch it with your hands for a long time.
Low pressure product inflation safety precautions
Low-pressure products such as balloons\swimming rings\toy balls are beyond the minimum pressure detection range of the product, and they cannot be preset.
សូមប្រើវាដោយប្រុងប្រយ័ត្ន។
ឯកសារ/ធនធាន
 |
Woowind AP2-2 Smart Tire Inflator [pdf] សៀវភៅណែនាំអ្នកប្រើប្រាស់ AP2-2 Smart Tire Inflator, AP2-2, Smart Tire Inflator, Tire Inflator, Inflator |