មាតិកា លាក់
1 VECTOR LTE-V2X Interface
2 ព័ត៌មានសុវត្ថិភាព
3 ការដំឡើងនិងការចាប់ផ្តើម
4 ឧបករណ៍ភ្ជាប់
5 ព័ត៌មានបន្ថែម
6 សំណួរគេសួរញឹកញាប់
7 ឯកសារ/ធនធាន
7.1 ឯកសារយោង

វ៉ិចទ័រ-ឡូហ្គោ

VECTOR LTE-V2X Interface

VECTOR-LTE-V2X-Interface-PRODUCT

ព័ត៌មានសុវត្ថិភាព

កំណត់ចំណាំសំខាន់ៗ

  • ប្រយ័ត្ន!
    • Do not operate the device without antennas! To avoid physical damage to the device, please attach the provided antennas to the device before operation!
  • ប្រយ័ត្ន!
    • The interface is exclusively designed for use by skilled personnel as its operation may result in serious personal injuries and damage to property. Therefore, only those persons may operate the interface who (i) have understood the possible effects of the actions which may be caused by the interface; (ii) are specifically trained in the handling with the interface, bus systems and the system intended to be influenced; and (iii) have sufficient experience in using the interface safely.

ការដំឡើងនិងការចាប់ផ្តើម

នីតិវិធីជាជំហាន ៗ

  1. Connect the device to the PC via Ethernet (either via a USB-to-Ethernet adapter or to your local network.
  2. Connect the antennas and the GNSS receiver to the device.
  3. Power up the device by supplying external voltage (e.g. with an appropriate cable offered by Vector) and press the power button.
  4. Ensure the first LED is in a permanent green state (operating system has booted successfully) and the second LED is blinking green (valid GNSS fix is available). A valid GNSS fix is mandatory for device operation. Without a valid GNSS fix, the device cannot transmit or receive messages.
  5. Open CANoes/CANalyzers Network Hardware Config Dialogue
    • Ath1: Select “C-V2X” as technology.
    • រៀបចំ: Open “Channel Mapping” and “Search Devices”. The device is found. Map the channel to “Ath1” and leave with “Ok”.
    • Adapt the channel’s default radio parameters, radio channel, bandwidth, transmission power and data rate to your needs and leave the dialogue with “Ok”.
  6. CANoe/CANalyzer and the device are now ready for operation.

ឧបករណ៍ភ្ជាប់

ផ្នែកខាងមុខ

VECTOR-LTE-V2X-Interface-FIG (1)

  • អ៊ីសឺរណិត (RJ45)
    • Connect your PC and the cube: tap to use the device with measurement applications (CANoe/CANalyzer).
  • LED (4x)
    • LED1: Permanent green state if the operating system has successfully booted.
    • LED2: Green blinking if GNSS fix is available.
    • LED3: Unassigned.
    • LED4: Unassigned.

ផ្នែកខាងក្រោយ

VECTOR-LTE-V2X-Interface-FIG (2)

  • 12V
    • Connector for external power supply.
  • ថាមពល
    • Press button to power up the device.
  • GNSS
    • This channel can be used to receive GNSS time and position.
  • V2X-A / V2X-B
    • The cube:tap has one channel with two RF connectors for diversity

ព័ត៌មានបន្ថែម

ទទួលបានព័ត៌មានបន្ថែម

  • ទស្សនារបស់យើង។ webគេហទំព័រសម្រាប់៖
    • ព័ត៌មាន
    • ផលិតផល
    • កម្មវិធីសាកល្បង
    • គាំទ្រ
    • ថ្នាក់បណ្តុះបណ្តាល
    • អាស័យដ្ឋាន

វ៉ិចទ័រ ព័ត៌មាន GmbH

Ingersheimer Straße 24 D-70499 Stuttgart Copyright © 2025 Vector Informatik GmbH. All rights reserved.

សំណួរគេសួរញឹកញាប់

  • Q: Can I operate the Cube: Tap without attaching antennas?
    • A: No, operating the device without antennas can lead to physical damage. Always attach the provided antennas before operation.
  • Q: Who should operate the cube tap interface?
    • A: The interface is designed for use by skilled personnel who understand its operations and have experience in handling such devices safely.

ឯកសារ/ធនធាន

VECTOR LTE-V2X Interface [pdf] ការណែនាំអ្នកប្រើប្រាស់
LTE-V2X Interface, LTE-V2X, Interface

ឯកសារយោង

ទុកមតិយោបល់

អាសយដ្ឋានអ៊ីមែលរបស់អ្នកនឹងមិនត្រូវបានផ្សព្វផ្សាយទេ។ វាលដែលត្រូវការត្រូវបានសម្គាល់ *