TCP ISREMOTE Remote Control
លក្ខណៈបច្ចេកទេសផលិតផល
- ម៉ាក: TCP
- ផលិតផល៖ ការបញ្ជាពីចម្ងាយ
- Model: ISREMOTE
- Works with any IS Motion Sensor
- Customization of luminaires
The TCP IS Remote works with any IS Motion Sensor to allow easy customization of any of your luminaires.
Remote Usage Instructions
ពន្លឺ LED
Set the brightness level when occupancy is sensed and luminaire is switched on.
ភាពរសើប
Adjust the occupancy sensing sensitivity of the sensor.
កាន់ពេលវេលា
Set the duration the sensor remains at full brightness before turning off or entering standby mode.
ឧបករណ៍ចាប់សញ្ញាពន្លឺថ្ងៃ
Preset threshold levels for the daylight sensing functions.
*In applicable sensors only
រង់ចាំ ឌីម
Adjust the lux value to act as the daylight threshold. This feature enables daylight sensor functionality in all applications. (Only applicable in certain sensors)
ម៉ោងរង់ចាំ
To set the bi-level dimming after the initial hold time. Setting standby dim level at 0% means the device will turn off after the initial hold time (Standard mode). Setting standby dim level to the other provided options will place the device in bi-level mode.
Set the current lux value as the daylight threshold. This feature enables the daylight sensor to function in all applications.
*In applicable sensors only
The daylight sensor is turned off and the sensor functions in standard or bi-level dimming mode.
ប៊ូតុងបិទ/បើក
Press the ON/OFF button, the light goes to permanent on or permanent off mode, and the sensor is disabled (Must press the AUTO button to quit this mode for setting).
Display the current/latest setting parameters in LED indicators (the LED indicators will turn on for showing the setting parameters).
ប៊ូតុងកំណត់ឡើងវិញ
Press RESET button, all settings go back the settings of the dip switch in sensor.
ប៊ូតុង SELECT
Select active parameter for editing after pressing DISP. The selected function will flash.
ប៊ូតុងយល់ព្រម
Select OK to save the selected settings to the remote.
Settings will be saved to the remote but will still need sent to the device
SEND Button
Press the SEND button to upload the current settings to the fixture (Press DISP to see current settings.) The fixture will flash on/off to confirm the settings have been received.
របៀបឈុតចំនួន 4 ជាមួយប៉ារ៉ាម៉ែត្រកំណត់ជាមុនដែលអាចប្រើបានដើម្បីផ្លាស់ប្តូរ និងរក្សាទុកក្នុងទម្រង់។
ប៊ូតុងស្វ័យប្រវត្តិ
Press AUTO button, the sensor starts to function and all settings remain the same as the latest status before the light is switched on/off.
TEST 2s Button
The button TEST 2s is for testing purpose sensitivity only after you choose sensitivity thresholds, then you press the TEST 2s button.
The sensor goes to test mode (hold time is only 2s) automatically, meanwhile the standby period and daylight sensor are disabled. Press AUTO button to quit from this mode.
LEFT/RIGHT Buttons
Navigate to LEFT and RIGHT to choose between options of the selected parameters in LED indicators
ប៊ូតុងឡើងលើ/ចុះក្រោម
Open and close smart daylight sensor. Press UP or DOWN, enter in the setting condition, the parameter LEDs of remote control will flash to be selected, press this button to open or close smart daylight sensor.
*In applicable sensors only
បច្ចេកវិជ្ជាបញ្ចេញពន្លឺដ៏ស្រស់ស្អាត
អស់រយៈពេលជាង 30 ឆ្នាំមកហើយ TCP បាននិងកំពុងរចនា បង្កើត និងផ្តល់ពន្លឺដែលមានប្រសិទ្ធភាពថាមពលទៅក្នុងទីផ្សារ។ សូមអរគុណចំពោះបច្ចេកវិជ្ជាទំនើប និងជំនាញផលិតរបស់យើង យើងបានដឹកជញ្ជូនផលិតផលភ្លើងបំភ្លឺដែលមានគុណភាពខ្ពស់រាប់ពាន់លាន។ ជាមួយនឹង TCP អ្នកអាចពឹងផ្អែកលើផលិតផលភ្លើងបំភ្លឺដែលត្រូវបានរចនាឡើងដើម្បីបំពេញតម្រូវការទីផ្សារ - ដែលផ្លាស់ប្តូរបរិយាកាសជុំវិញរបស់អ្នក និងផ្តល់ភាពកក់ក្តៅដល់អ្នក - ពន្លឺដែលបង្កើតភាពស្រស់ស្អាតជាមួយនឹងរាល់ការបិទបើក។
សម្រាប់ព័ត៌មានបន្ថែមអំពីគុណភាព និងការថែទាំដែល TCP អាចចែកចាយបាន សូមទូរស័ព្ទមកយើងតាមរយៈលេខ 800.324.1496 ឬចូលទៅកាន់ tcpi.com
325 គampយើងបណ្ឌិត | Aurora, Ohio 44202 | P: 800.324.1496 | F: 877.487.0516
សំណួរដែលសួរញឹកញាប់
Q: How do I know if my sensor is compatible with the TCP IS Remote?
A: The TCP IS Remote works with any IS Motion Sensor, ensuring compatibility for customization of luminaires.
Q: Can I adjust the daylight sensing functionality of my luminaire?
A: Yes, you can set threshold levels and adjust the sensitivity of the daylight sensor in applicable sensors.
ឯកសារ/ធនធាន
 |
TCP ISREMOTE Remote Control [pdf] សៀវភៅណែនាំ ISREMOTE, ISREMOTE Remote Control, ISREMOTE, Remote Control, Control |