SHOOTERS 3D IPSC IDPA Modular Box

ការណែនាំអំពីផលិតផល

Thank you for choosing our IPSC IDPA Modular Box.

It is used to check & verify gun/pistol size compliance with most common IPSC & IDPA divisions:

• IPSC Handguns: Standard & Classic
• IDPA: ESP, SSP, CDP, CO, CCP
  • We always strive to improve our products in terms of quality and user friendliness, so your feedback would be very appreciated and welcomed.
  • For feedback, questions and warranty claims, please contact us on info@shooters3d.com.

នៅក្នុងកញ្ចប់

All parts are visually marked with engraved lettering and can also be printed in 2 or more colors, so it is easy to identify individual components.

1. IPSC & IDPA Modular Box (1x)
2. 2-sided Lid (1x)
3. IDPA side insert (ESP, SSP, CDP, CO) (1x)
4. IPSC back insert (1x)
5. IDPA CCP side insert (1x)
6. IDPA CCP back insert (1x)
7. IDPA CCP bottom insert (1x)

ការចាប់ផ្តើម

• IPSC
  Internal dimension of the box is 225 x 150 x 45 mm. This is achieved with box fully assembled and only IPSC back insert inside. Use lid turned with IPSC marking on top (always visible).
• IDPA
  Internal dimension of the box is 8 3/4 x 6 x 1 5/8 inches (22.23 x 15.24 x 4.13 cm) for ESP, SSP, CDP, CO and 7¾ x 5⅜” x 1⅜ inches (19.68 cm x 13.65 cm x 3.49 cm) for CCP. Size for ESP, SSP, CDP, CO is achieved with box fully assembled and only IDPA side insert in. For IPDA CO you need to remove backwall (pull up). For CCP remove IDPA side insert and insert all 3 CCP insert: side, back and then bottom. Always use lid turned with IDPA letters on top (visible).

All inserts are to be pushed in and taken out from the top, vertically. Be careful not to use excessive force. Due to small tolerances, some insert might go in our out harder, but should become easier after some use.

លក្ខណៈបច្ចេកទេស

PSC IDPA Modular Box is printed out of durable PETG (Polyethylene Terephthalate Glycol) material.

• បំពេញ៖ 15-25% (depending on parts)
• លំនាំបំពេញ៖ gyroid
• ទំងន់ផលិតផល៖ approx.. 750 g
• វិមាត្រផលិតផល (assembled): 247 x 177 x 67 mm
  • Please don’t expose product to temperatures higher then 70°C.
  • Please note that product dimension can deviate +- 1 % due to 3D printed material expansion/shrinkage.
  • Shooters3D IPSC IDPA Modular Box is in no way directly associated or certified by IDPA and IPSC organizations and is not to be used as their of official product.

ទាក់ទង​យើង

• S3D, Bled, Slovenia
• info@shooters3d.com

សំណួរគេសួរញឹកញាប់

Is the Shooters3D IPSC IDPA Modular Box officially certified by IDPA and IPSC organizations?

No, the product is not directly associated or certified by IDPA and IPSC organizations and should not be considered their official product.

ឯកសារ/ធនធាន

SHOOTERS 3D IPSC IDPA Modular Box [pdf] សៀវភៅណែនាំអ្នកប្រើប្រាស់ IPSC IDPA Modular Box, IDPA Modular Box, Modular Box

ឯកសារយោង

• សៀវភៅណែនាំអ្នកប្រើប្រាស់