QwikProducts QT8202 QwikPad for
ការណែនាំអំពីការដំឡើង
Choose a generator anchoring method that meets wind loading requirements in your area. Visit www.qwik.com/qwikpad4gen for the most up-to-date engineering documentation.
- ត្រួតពិនិត្យមាតិកាកញ្ចប់ផ្នែករឹង៖
Hardware needs are specific to generator model.
The hardware shown at the left is included with the Universal Pad model (QT8202).
See the model-specific hardware chart at the bottom of this section.- A – 2 WASHERS, FLAT 3/8″ (Ø 1¼”)
- B – 4 WASHERS, FLAT 3/8″ (Ø 7/8”)
- C – 4 WASHERS, LOCK 3/8”
- D – 3 BOLTS, HEX, 3/8-16 (4½”)
- E – 4 BOLTS, HEX, 3/8-16 (1½”)
- F – 4 BOLTS, HEX, 3/8-16 (2½”)
- G – 2 BOLTS, HEX, 3/8-16 (23/4”)
- H – 4 BOLTS, HEX, 3/8-16 (7/8”)
- I – 4 BOLTS, HEX, 3/8-16 (3¼”)
Refer to the following anchorage configurations to identify general mounting points and appropriate hardware for your specific generator model.
Refer to the manufacturer’s specifications for details about the proper mounting points/methods for your specific generator model.
(SUPER UNIVERSAL CONFIGURATION)
QT8202 ANCHORAGE
កំពូល VIEW
▼FRONT▼
(BRIGGS & STRATTON-STEEL ENCLOSURE CONFIGURATION)
QT8210 ANCHORAGE
កំពូល VIEW
▼FRONT▼
(BRIGGS & STRATTON–POWER PROTECTION SERIES CONFIGURATION)
QT8215 ANCHORAGE
កំពូល VIEW
▼FRONT▼
(BRIGGS & STRATTON-ALUMINUM ENCLOSURE CONFIGURATION)
QT8220 ANCHORAGE
កំពូល VIEW
▼FRONT▼
(GENERAC/HONEYWELL CONFIGURATION)
QT8231 ANCHORAGE
កំពូល VIEW
▼FRONTY▼
(KOHLER CONFIGURATION)
QT8240 ANCHORAGE
កំពូល VIEW
▼FRONTY▼
ព័ត៌មានលម្អិតអំពីយុថ្កា
5010906_REV-H / 1201890001
តម្រូវការផ្នែករឹងជាក់លាក់នៃគំរូ
ម៉ូដែល ការពិពណ៌នា QTY ប្រវែង BOLT បោកគក់ QT8202 Generac/Honeywell, Kohler, Cummins, B&S, Pwr. Protecn. Series, Steel, & Aluminum ០១៤៨៦០៧៤-០០៤ 7/8”, 1½”, 2½”, 23/4”, 3¼”, 4½” Cummins A and C All others B and C QT8210 B&S, Stee 4 7/8″ ខ និង គ QT8215 B&S, Pwr. Protectn. Series 4 ៦៩ ម។ ក្រ។ ” ខ និង គ QT8220 B&S, Aluminum 4 ៦៩ ម។ ក្រ។ ” ខ និង គ QT8231 Generac/Honeywell 4 4½”, 2½” ខ និង គ QT824 Kohler 4 1½” ខ និង គ
- Locate the fill port cap (center of short side, nearest the product label).
Ensure the cap is securely pressed into the pad, and then tip the pad on the edge where the plug is located. This process shifts the powdered gelling agent contained inside the pad toward the fill port.
- Place the QwikPad for Generators on level, compacted ground where the equipment is to be installed (or on top of an existing, level concrete pad).
- Remove the fill port cap. Insert a garden hose into the fill port and fill QwikPad for Generators to the top with tap water.
Do not overfill – Overfilling could result in losing a portion of the gelling agent. Replace the fill port cap.
In areas that experience frequent freeze-thaw cycles, only fill the QwikPad for Generators 80% full for increased lifetime. This can be done by filling the pad with water to a depth of only 3 inches – when filling, use a dipstick or straw to periodically check the liquid height. Verify an 80% fill still meets local wind regulations by referring to our online calculator and information.
- Additional Anchor (Required for some installations. QT8381 and QT8382 hardware sold separately).
Install concrete or ground anchor as required by wind load calculations.
យុថ្កាបេតុង (QT8381) ការតំឡើង៖- With the pad in place, drill a hole in the concrete using a 3/16” masonry bit aligned with the anchor hole centrally located on the QwikPad to 1.375” minimum depth.
- Secure the pad using the 1/4″x 5″ concrete anchor with fender washer.
round Anchor (QT8382) Installation: - With pad in place, install ground anchor in the anchor hole centrally located on the QwikPad.
- Place the equipment onto the QwikPad for Generators and center.
Secure the generator to the pad using the included stainless steel mounting bolts with lock and flat washers. Torque to 20-25 FT•LB.
Refer to the table at the bottom of Step 1 for the appropriate hardware.
ចំណាំ៖ Mounting bolt placement is specific to the generator model.
ជំនួយអតិថិជន
សម្រាប់ព័ត៌មានលម្អិត ឬព័ត៌មានបន្ថែមអំពី ស
QwikPad for Generators, visit www.qwik.com/qwikpad4gen, អ៊ីមែល info@qwik.com ឬទូរស័ព្ទទៅលេខ 1-៨៦៦-៤៤៧-២១៩៤
QwikProducts® and QwikPad® are registered trademarks of Mainstream Engineering Corporation® Rockledge, Florida 32955, ៨៦៦-៤៤៧-២១៩៤, © 2025 Mainstream Engineering Corporation®
U.S. Patents: #10,557,589, #11,384,896, #11,460,148, #11,460,149, #11,649,921, #D1,007,425, #D1,012,858, # D1,012,859
ឯកសារ/ធនធាន
 |
QwikProducts QT8202 QwikPad for Generators [pdf] សេចក្តីណែនាំ QT8202, QT8210, QT8215, QT8220, QT8202 QwikPad for Generators, QT8202, QwikPad for Generators, Generators |