MAKE NOISE QXG Quad Low Pass Gate

ការដំឡើង

គ្រោះថ្នាក់​អគ្គិសនី​!

• បិទករណី Eurorack ជានិច្ច ហើយដកខ្សែថាមពលចេញ មុនពេលដោត ឬដកខ្សែតភ្ជាប់ក្រុមប្រឹក្សាភិបាល Eurorack ណាមួយ។ កុំប៉ះស្ថានីយអគ្គិសនីណាមួយ នៅពេលភ្ជាប់ខ្សែ ក្រុមប្រឹក្សាភិបាល Eurorack ។
• The Make Noise QXG is an electronic music module requiring 65mA of +12VDC and 75mA of -12VDC regulated voltage និងបង្កាន់ដៃចែកចាយដែលមានទម្រង់ត្រឹមត្រូវដើម្បីដំណើរការ។ វាត្រូវតែត្រូវបានដំឡើងឱ្យបានត្រឹមត្រូវទៅក្នុងប្រអប់ប្រព័ន្ធសំយោគម៉ូឌុលនៃទ្រង់ទ្រាយ Eurorack ។
• ទៅ http://www.makenoisemusic.com/ សម្រាប់អតីតamples នៃប្រព័ន្ធនិងករណី Eurorack ។
• ដើម្បីដំឡើង សូមស្វែងរក 12HP នៅក្នុងស្រោមឧបករណ៍សំយោគ Eurorack របស់អ្នក បញ្ជាក់ការដំឡើងត្រឹមត្រូវនៃខ្សែឧបករណ៍ភ្ជាប់របស់ Eurorack bus board នៅផ្នែកខាងក្រោយនៃម៉ូឌុល (សូមមើលរូបភាពខាងក្រោម) ដោតខ្សែឧបករណ៍ភ្ជាប់ bus board ចូលទៅក្នុងបន្ទះ bus style Eurorack ដោយគិតពីបន្ទាត់រាងប៉ូល ដូច្នេះ RED ឆ្នូតនៅលើខ្សែត្រូវបានតម្រង់ទៅខ្សែ NEGATIVE 12 Volt ទាំងនៅលើម៉ូឌុល និងបន្ទះឡានក្រុង។ នៅលើ Make Noise 6U ឬ 3U Busboard បន្ទាត់អវិជ្ជមាន 12 Volt ត្រូវបានចង្អុលបង្ហាញដោយឆ្នូតពណ៌ស។

កំពូល

សូមយោងទៅលើការបញ្ជាក់របស់អ្នកផលិតករណីរបស់អ្នកសម្រាប់ទីតាំងនៃការផ្គត់ផ្គង់អវិជ្ជមាន។

ការណែនាំ

• The Quad Stereo Gate (QXG) music synthesizer module is a Four Channel Stereo Low Pass Gate and Mixer. It follows in the footsteps of the QMMG, Optomix, RxMx, DynaMix, LxD, and DXG.
• A pair of QXG modules is specially designed to connect to PoliMATHS and our forthcoming multi-channel oscillator to complete the eight voice core of the New Universal Synthesizer System. When these connections are made, the eight channels of the oscillator are distributed to the eight signal inputs, while the eight channels of the PoliMATHS are distributed to the eight control inputs.
• Like the DXG before it, the QXG utilizes a new low pass gate circuit that does not use vactrols. This circuit is 100% analog and its response was arrived at after many months tailoring it to meet or exceed the expectations that have been set by all the vactrol low pass gates that Make Noise has created over the years.
• As on all of our low pass gates, the QXG’s CTRL parameter is used to set both the amplitude and the frequen-cy content of the sound that passes through it.
• Additionally the QXG adds a Vactrol button to select between a Slow, vactrol-type response emulating the decay time of a vactrol (Vactrol button ON), and a Fast precision response that still maintains the gentle filter-ing characteristic (Vactrol button OFF). Fast response can be especially useful when patching QXG with complex and quickly-changing functions such as those generated by PoliMATHS.
• The QXG also includes a Stereo Sum Output with voltage controllable Stereo Spread to quickly route all four channels across the stereo field. Each channel also has an individual output that removes the channel from the Sum when patched.
• QXG also includes signal and control input headers for creating pre-patched connections from the outputs of PoliMATHS and our forthcoming multi-channel oscillator.
• QXG’s stereo Aux input can be used to chain together larger decentralized mixes, and are also useful in quickly connecting two QXG together when used with the eight channels of PoliMATHS and #$%@$!, creating an eight channel stereo submix if so desired.

ការគ្រប់គ្រងបន្ទះ

1. Left (Mono) and Right Aux Inputs: Patch a signal to these inputs to mix it directly to the Mix outputs. Useful for chaining with a second QXG for eight-channel N.U.S.S. patches, or adding any other audio source to the mix. Patch only to Left input for mono use (left input will appear at both Mix outputs).
2. Left and Right Mix Outputs: Stereo mix of all channels and Aux inputs according to the individual channels’ control levels and the Xpread parameter.

ការគ្រប់គ្រងបន្ទះ

1. Signal Inputs 1-4: Signal inputs for the four low pass gate circuits. Normalled to Signal Input header for use with N.U.S.S. audio sources (#!$%&!*#@ or MultiMod). Patching to the input breaks this connection, per channel.
2. Control Inputs 1-4: Control voltage inputs for the four low pass gate circuits. Normalled to Control Inputs header for use with N.U.S.S. control voltage sources (PoliMATHS or MultiMod). Patching to the control input breaks this connection, per channel.
3. Control combo pots 1-4: Panel controls for the low pass gate circuit. Attenuates signal at Control Input, or normalled control signals from N.U.S.S. Control Inputs header. If header is not in use, combo pot operates as a panel control when its Control Input is unpatched. Channel outputs 1-4: Outputs for the four low pass gate circuits. Unpatched channels are sent to the Mix outputs via the XPREAD parameter. Patching an output removes the channel from the Mix.

1. XPREAD Panel Control: Sets the Stereo Spread for the four low pass gate channels. At 12:00, all channels are centered. At full clockwise, channels are distributed to the outputs from left to right: Channel 1 in left channel only, Channel 2 weighted left, Channel 3 weighted right, Channel 4 in right channel only. At full counterclockwise, channels are distributed to the outputs from right to left: Channel 4 in left channel only, Channel 3 weighted left, Channel 2 weighted right, Channel 1 in right channel only.
2. XPREAD CV Input: Control voltage input for XPREAD parameter.
3. XPREAD CV Input attenuverter: Bi-polar attenuator for XPREAD CV input.
4. Vactrol Button: Selects between a Slow response emulating the decay time of a vactrol (Vac-trol button ON), and a Fast response that still maintains the gentle low pass gate filtering characteristic (Vactrol button OFF).

សំណួរគេសួរញឹកញាប់

What is the purpose of the Vactrol button on the QXG module?

The Vactrol button allows users to select between a slow vactrol-type response and a fast precision response for controlling the sound passing through the module.

ឯកសារ/ធនធាន

MAKE NOISE QXG Quad Low Pass Gate [pdf] សៀវភៅណែនាំអ្នកប្រើប្រាស់ QXG Quad Low Pass Gate, QXG, Low Pass Gate, Pass Gate, Gate

ឯកសារយោង

• សៀវភៅណែនាំអ្នកប្រើប្រាស់