Litetronics LED High Bay SL

What Comes in the Box

• 1' 0-10V and 12V(+) wires
• 6' Power and ground wires
• 3.3' Safety cable
• Round hook M10 (1)
• Waterproof wirenuts (2)
• Installation instructions

Tools Needed

• Wire Stripper
• Wire Cutter

Safety Instructions and Warnings

When using electrical equipment, basic safety precautions should always be observed.

READ AND FOLLOW ALL SAFETY INSTRUCTIONS.

• Consult a qualified electrician to ensure correct branch circuit conductor.
• This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
• Installation should only be conducted by a qualified electrician in accordance with NEC and any relevant local building codes.
• Risk of fire or electric shock. High Bay installation requires knowledge of luminaires electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician.
• Be certain electrical power is OFF before and during installation and maintenance.
• High Bay must be connected to a wiring system with an equipment-grounding conductor.
• Make sure the supply voltage is the same as the rated High Bay voltage.
• To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or sharp objects.
• No user serviceable parts inside of High Bay luminaires.
• Secure heat sink with safety cable. ✔️

Attention

1. Please check if there is any damage during shipping. If so, please contact Litetronics customer service.
2. Please read the installation instruction carefully to check whether all the accessories are included.
3. After confirmation, install the fixture according to installation steps.

Installation Procedure

READ ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION.

1. Turn off power at the circuit breaker.
2. Select CCT and wattage by removing the waterproof protective cover by unscrewing. Please make sure that the protective cover is put back on after setup.

   CCT and Wattage Slide Switch Settings: The fixture features slide switches accessible after removing a waterproof cover. The wattage can be set to 200W, 150W, or 100W. The Correlated Color Temperature (CCT) can be set to 5000K, 4000K, or 3500K.

   Note: Default settings are 200W and 5000K.

3. High Bay Luminaire can be mechanically supported to hook, chain, or cable (not included) by securing the round hook on top of the fixture.
4. Once luminaire is supported, attach the included safety cable to a beam or permanent structural support.
5. Make wiring connections:
   • To enable 0-10V dimming with a dimmer, make connections between the dimming wires (purple (+) and pink (-)) and the dimmer, using the included waterproof wire nuts.
   • Then, connect the input wires to AC branch circuits as noted in the wiring diagrams. This should be in accordance with national and local codes.
6. Restore power at the circuit breaker and subsequently switch on the dimmer (if applicable).

Wiring Diagrams

General Wiring Diagram (Figure 1)

This diagram illustrates the 0-10V dimming connections. The purple wire (Dim+) connects to the dimmer's (+) terminal, and the pink wire (Dim-) connects to the dimmer's (-) terminal. The gray/pink wires are for sensor connections. The main input wires (black, white, green) connect to the AC branch circuit.

Fixture Illustration

The illustration shows the LED High Bay fixture with its components: a safety cable, a round hook for mounting, and the main wiring leads (Ground/Neutral/Line) and 0-10V dimming wires.

Wiring for 120V & 277V (Figure 2)

Connect the GREEN wire to GROUND, the WHITE wire to NEUTRAL, and the BLACK wire to LINE (HOT).

Wiring for 208V, 240V & 480V (Figure 3)

Connect the GREEN wire to GROUND, the WHITE wire to LINE 1 (HOT), and the BLACK wire to LINE 2 (HOT).

Contact Information

Litetronics

6969 W. 73rd Street
Bedford Park, IL 60638

Website: www.litetronics.com

Email: CustomerService@Litetronics.com

Phone: 1-800-860-3392

Certifications

FCC Compliant (USA)

RoHS Compliant