Sansui S-X1130/S-X1100 Service Manual
Audio Video Stereo Receiver
Introduction
This document is the service manual for the SANSUI S-X1130 and S-X1100 Audio Video Stereo Receiver (Silver & Black Models). It provides detailed technical information, specifications, diagrams, adjustment procedures, and parts lists necessary for servicing the unit.
Model Names: S-X1130, S-X1100
Product Type: Audio Video Stereo Receiver
Brand: Sansui
Specifications
| Category | Details |
|---|---|
| Audio Section | |
| Power output | Min. RMS, both channels driven, from 20 to 20,000 Hz, with no more than 0.005% total harmonic distortion: 130 watts per channel into 8 ohms. Load impedance: 8 ohms. Total harmonic distortion: less than 0.005% at or below rated min. RMS power output (from POWER AMP IN). |
| Frequency response (at 1 watt) | from POWER AMP IN: 5 to 180,000 Hz, +0 dB, -3.0 dB |
| RIAA curve deviation (PHONO MM, 20 Hz to 20 kHz) | +0.2 dB, -0.2 dB |
| Input sensitivity and impedance (at 1 kHz) |
|
| Output level (at 1 kHz) |
|
| Signal to noise ratio (at 1 kHz, short-circuit, A-network) |
|
| Video Section (S-X1130 only) | |
| VIDEO INPUT sensitivity (Impedance) | 1.0 Vp-p / 75 ohms |
| VIDEO OUTPUT level/Impedance | 1.0 Vp-p / 75 ohms |
| AUDIO INPUT sensitivity (Impedance) | -6 dBs / 47 kohms |
| AUDIO OUTPUT level/Impedance | -6 dBs / 47 kohms |
| VHF OUT signal | 3 ch or 4 ch (NTSC) |
| FM Section | |
| Tuning range | 88 to 108 MHz |
| Usable sensitivity | Mono: 10.3 dBf / Stereo: 19 dBf |
| 50 dB quieting sensitivity | Mono: 14 dBf / Stereo: 37 dBf |
| Signal to noise ratio (at 65 dBf) | Mono: 80 dB / Stereo: 76 dB |
| Distortion (at 65 dBf WIDE) |
|
| Alternate channel selectivity (at 400 kHz) | NARROW: 60 dB |
| Capture ratio | 1.0 dB |
| Spurious response ratio | 90 dB |
| IF response ratio | 90 dB |
| Stereo separation | 45 dB at 1,000 Hz |
| Frequency response | 30 to 15,000 Hz, +0.2 dB, -0.5 dB |
| Antenna input impedance | 300 ohms balanced / 75 ohms unbalanced |
| AM Section | |
| Tuning range | 530 to 1,600 kHz |
| Usable sensitivity | 49 dB/m |
| Selectivity | 30 dB |
| Signal to noise ratio (at 30% Modulation, 1mV/m) | Mono: 50 dB |
| Distortion (at 30% Modulation, 1mV/m) | Mono: less than 0.5% |
| Others | |
| Power requirements | 120, 220, 240 V, (50/60 Hz) |
| Power voltage | 120 V (60 Hz) |
| <S-X1130> | |
| Power consumption | 450 watts / 530 VA Rated |
| Dimensions (W x H x D) | 430 mm (16-15/16") W x 161 mm (6-3/8") H x 421 mm (16-5/8") D |
| Weight | 16.3 kg (35.9 lbs.) net / 18.0 kg (39.7 lbs.) packed |
| <S-X1100> | |
| Power consumption | 370 watts / 430 VA Rated |
| Dimensions (W x H x D) | 430 mm (16-15/16") W x 161 mm (6-3/8") H x 421 mm (16-5/8") D |
| Weight | 14.7 kg (32.4 lbs.) net / 16.4 kg (36.2 lbs.) packed |
Design and specifications subject to change without notice for improvements.
Cautions
CAUTION
- Parts identified by the symbol ⚡ on the schematic diagram and the parts list are critical for safety. Use only replacement parts that have critical characteristics recommended by the manufacturer.
- Make leakage-current or resistance measurements to determine that exposed parts are acceptably insulated from the supply circuit before returning the appliance to the customer.
Symbol Meanings:
- UL: Manufactured for U.S.A market. (Underwriters Laboratories approved model.)
- CSA: Manufactured for Canadian market.
- SA: Manufactured for South African market.
- BS, UK: Manufactured for United Kingdom market.
- EU: Manufactured for European market.
- AS: Manufactured for Australian market.
- XX: Standard Version.
- NON MARK: Common Parts.
Notes on Parts:
- Some printed circuit boards are not supplied as assembled. To separate these in this service manual, the stock No's are not indicated at the ends of the board names. However, the individual parts on the circuit boards are provided by orders.
- Since some of capacitors and resistors are omitted from parts lists in this service manual, refer to the Common Parts List for capacitors & resistors, which was issued on February 1983.
Abbreviations
Abbreviations List:
| Abbreviation | Meaning | Abbreviation | Meaning |
|---|---|---|---|
| C.R. | Carbon Resistor | E.B.L. | Low Leak Bi-Polar Electrolytic Capacitor |
| S.R. | Solid Resistor | Ta.C. | Tantalum Capacitor |
| Ce.R. | Cement Resistor | F.C. | Film Capacitor |
| M.R. | Metal Film Resistor | M.P. | Metalized Paper Capacitor |
| F.R. | Fusing Resistor | P.C. | Polystyrene Capacitor |
| N.I.R. | Non-Inflammable Resistor | G.C. | Gimmic Capacitor |
| A.R. | Array Resistor | A.C. | Array Capacitor |
| C.C. | Ceramic Capacitor | V.R. | Variable Resistor |
| C.T. | Ceramic Capacitor, Temperature Compensation | S.V.R. | Semi Variable Resistor |
| E.C. | Electrolytic Capacitor | SW. | Switch |
| E.L. | Low Leak Electrolytic Capacitor | Chip R. | Chip Resistor |
| E.B. | Bi-Polar Electrolytic Capacitor | Chip C. | Chip Capacitor |
Block Diagrams
1. Block Diagram - Tuner Section
This section details the internal structure of the Tuner section. Key components and signal paths include:
- FM Front-end: Receives FM signals.
- FM IF Amp: Amplifies the Intermediate Frequency signal.
- FM Detector: Demodulates the FM signal.
- MPX Decoder: Decodes the stereo multiplex signal.
- AM Section: Handles AM reception. Includes AM Control Voltage and AM Local Frequency circuits.
- AM Stereo Detector: Processes AM stereo signals.
- PLL & Control: Phase-Locked Loop for tuning and control functions. Includes Prescaler, Memory, Tuning Control, and display drivers.
- AM Stereo Systems: The diagram indicates support for MAGNAVOX, KAHN-HAZELTINE, MOTOROLA, and HARRIS AM stereo systems.
Diagrams on page 3 illustrate these interconnections.
Circuit Diagrams
Audio & Video Section
This section covers the audio processing and video signal handling. Key functional blocks include:
- EQ Amp: Equalizer amplifier for phono input.
- TONE Control: Bass, Midrange, Treble, and Loudness controls.
- VOLUME, BALANCE: Audio level and stereo balance controls.
- Power Amp: Amplifies the audio signal for speakers.
- INPUT SELECTOR: Switches between various audio/video sources (PHONO, TAPE, AUX/DA, VIDEO IN, TUNER, MIC).
- PROTECTOR: Protects speakers from DC offset or abnormal signals.
- MULTI DIMENSION: A sound processing feature.
- NOISE FILTER, MIXING: Signal processing for audio.
- SYNC Amp: Synchronizes video signals.
- VIDEO OUT Buffer Amp: Buffers the video output signal.
- VHF IN, RF Modulator, VHF OUT: For VHF signal input and output.
Diagrams on page 4 illustrate these interconnections.
Adjustment Procedures
This section details the calibration and alignment procedures for various sections of the receiver.
2) FM STEREO Adjustment
These procedures require specific test equipment like an FM SSG (Signal Generator), VTVM (Vacuum Tube Voltmeter), and Oscilloscope.
| STEP | SUBJECT | FEED SIGNAL | FROM | TO | MEASURE OUTPUT | ADJUST | ADJUST FOR | REMARKS |
|---|---|---|---|---|---|---|---|---|
| 1. | Auto Stop Level Adj. | 98MHz ANT Input 35dBf (29.8dB), 1kHz (100% MOD.), FM SSG | ANT Terminal | Point E | Digital display | fTC1 (F-4742) | 25 kHz | •Short between Point B & Point (Pin 36 & 42 of fIC1) (F-4742) •Repeat procedures as stated in subject 1 & 2. •Confirm that lock Indicator turns ON |
| 2. | Separation Adj. (WIDE band) | 98MHz ANT Input 65 dBf (59.8dB), 19 kHz (9% MOD.) + 1kHz (100% MOD.), STEREO SG. | ANT Terminal | Point F (Ground) | VTVM & SCOPE | fVR₁ (F-4742) | Max. DC Volt | •Repeat procedures as stated in subject 1 & 2. •Confirm that lock Indicator turns ON |
| 3. | Reference Frequency Adjustment | 15kHz LPF | SCOPE IN/OUT | GENESCOPE IN/OUT | VTVM | fVR₁ (center position) | IFT Coil (Front-end) & dT1 (F-4741) | Steep linearity of S curve. Make symmetrical S curve. |
2-2. AM Adjustment
These procedures require an AM SSG, VTVM, and Oscilloscope.
| STEP | SUBJECT | FEED SIGNAL | FROM | TO | MEASURE OUTPUT | ADJUST | ADJUST FOR | REMARKS |
|---|---|---|---|---|---|---|---|---|
| 1. | IF Coil Adj. | Output 60dB, 98MHz ANT Input 20dBf (14.8dB), 1kHz (100% MOD.), FM SSG | Point (eR19) (F-4741) | Between Point (JW1) & Earth (F-4741) | Genescope | eT3 (F-4741) | Max. Waveform | •Since the dT1 has already adjusted, perform only a fine adjustment in this procedure. |
| 2. | Tuning Adj. | 98MHz ANT Input 65dBf (59.8dB), 1kHz (100% MOD.), FM SSG | ANT terminal | Between Point (dR11) (F-4741) & Earth | Genescope | dT2 (F-4741) | DC 0V ±30mV | •Perform the automatic search tuning operation by depressing the TUNING button. |
| 3. | Signal Ind. Level Adj. | 98MHz ANT Input 65dBf (59.8dB), 1kHz (100% MOD.), FM SSG | ANT terminal | Between TP1 & TP2 (near dIC2) | DC Volt Meter | dT3, dT1 (F-4741) | DC 0V ±30mV | •Confirm that lock indicator turns ON. |
| 4. | RF Adj. | Input 30dB 400Hz (30% MOD.), AM SSG | ANT terminal | TAPE-2 REC L-CH or R-CH | VTVM & SCOPE | eT1 (F-4741) | Max Output | •The following table shows relations among FM SG attenuator indication (dB), available power ratio (dBf) and antenna terminal voltage (dB/µV) in each indication type. |
| 5. | Tuning Adj. | Input 30dB 400Hz (30% MOD.), AM SSG | ANT terminal | Same as above | VTVM & SCOPE | eT2 (F-4741) | Max Output | •FM SG output and ANT terminal (3000) of the unit. |
| 6. | Auto Stop Level Adj. | Input 65dB 400Hz (30% MOD.), AM SSG | ANT terminal | Signal Ind. (sFL1) | Digital Display (sFL1) | eVR2 (F-4741) | Tune the tuner to 999 (or 1000kHz) kHz by using the automatic search tuning operation. | •Confirm that lock indicator turns ON. |
| 7. | Signal Level Adj. | Input 65dB 400Hz (30% MOD.), AM SSG | ANT terminal | Signal Ind. (sFL1) | Digital Display (sFL1) | eVR1 (F-4741) | Tune the tuner to 999 (or 1000kHz) kHz by using the automatic search tuning operation. | •Indicator light up. |
2-1. AM IF Adjustment & Tuning Adjustment
Note: 1. Connect AM loop antenna to AM antenna terminal.
| STEP | SUBJECT | FEED SIGNAL | FROM | TO | MEASURE OUTPUT | ADJUST | ADJUST FOR | REMARKS |
|---|---|---|---|---|---|---|---|---|
| 1. | IF Coil Adj. | 1000kHz ANT Input 80 dB L MODE, 1kHz (100% MOD.), AM Stereo SG | Between Point A (Pin 24 of fIC1) & Earth | Freq. counter | fTC1 (F-4742) | 25 kHz | IFT Coil (Front-end) | •Repeat procedures as stated in subject 1 & 2. |
| 2. | Tuning Adj. | 98MHz ANT Input 65dBf (59.8dB), 1kHz (100% MOD.), FM SSG | Between Point B (Pin 13 of dIC2) & Earth | DC Volt Meter | dT2 (F-4741) | DC 0V ±30mV | Steep linearity of S curve. | •Repeat procedures as stated in subject 1 & 2. |
| 3. | Signal Ind. Level Adj. | 98MHz ANT Input 65dBf (59.8dB), 1kHz (100% MOD.), FM SSG | Between TP1 & TP2 (near dIC2) | DC Volt Meter | dT3, dT1 (F-4741) | DC 0V ±30mV | Make symmetrical S curve. | •Confirm that lock Indicator turns ON. |
| 4. | RF Adj. | Input 30dB 400Hz (30% MOD.), AM SSG | ANT terminal | TAPE-2 REC L-CH or R-CH | VTVM & SCOPE | eT1 (F-4741) | Max Output | •The following table shows relations among FM SG attenuator indication (dB), available power ratio (dBf) and antenna terminal voltage (dB/µV) in each indication type. |
| 5. | Tuning Adj. | Input 30dB 400Hz (30% MOD.), AM SSG | ANT terminal | Same as above | VTVM & SCOPE | eT2 (F-4741) | Max Output | •FM SG output and ANT terminal (3000) of the unit. |
| 6. | Auto Stop Level Adj. | Input 65dB 400Hz (30% MOD.), AM SSG | ANT terminal | Signal Ind. (sFL1) | Digital Display (sFL1) | eVR2 (F-4741) | Tune the tuner to 999 (or 1000kHz) kHz by using the automatic search tuning operation. | •Confirm that lock indicator turns ON. |
| 7. | Signal Level Adj. | Input 65dB 400Hz (30% MOD.), AM SSG | ANT terminal | Signal Ind. (sFL1) | Digital Display (sFL1) | eVR1 (F-4741) | Tune the tuner to 999 (or 1000kHz) kHz by using the automatic search tuning operation. | •Indicator light up. |
2-3. Driver Circuit Adjustment
Note: 1. Room Temperature: 18°C~28°C. 2. Master Volume: Minimum. 3. For this adjustment, run the unit for more than 2 minutes after the power is switched ON.
| STEP | SUBJECT | MEASURE OUTPUT | ADJUST | ADJUST FOR | REMARKS | |
|---|---|---|---|---|---|---|
| 1. | Bias Current Adj. L-CH | Between emitter terminals of kQ8L and kQ9L (TP1) (F-4745) | DC Volt Meter | KVR1L (F-4745) | DC 3.5mV±1.5mV | •Before turning ON power switch, turn kVR1L, R counterclockwise. •This bias current value into voltage by ohms law. |
| 2. | Bias Current Adj. R-CH | Between emitter terminals of kQ8R and kQ9R (TP2) (F-4745) | DC Volt Meter | KVR1R (F-4745) | DC 3.5mV±1.5mV | •Before turning ON power switch, turn kVR1L, R counterclockwise. •This bias current value into voltage by ohms law. |
IC Terminal Functions & Block Diagrams
This section details the integrated circuits used in the SANSUI S-X1130/S-X1100 receiver.
•TA7302P (FM IF Amp. IC)
Block diagram and terminal functions for the FM IF Amplifier IC.
•BA6148 (Meter Drive IC)
Block diagram and terminal functions for the Meter Drive IC.
•TA7317P (Protector IC)
Block diagram and terminal functions for the Protector IC, including Power Supply ON/OFF Detection, Muting, Constant-voltage regulator, Relay Drive, Schmitt Trigger, Over Current Detection, and DC Voltage Detection circuits.
•HA12412 (FM Detector IC)
Block diagram and terminal functions for the FM Detector IC, including 1st IF Amp, IF Amp, Killer, 2nd IF Amp, 3rd IF Amp, Quadrature Detector, AFC Amp, Audio Amp, Mute Control Driver, and Level Detector circuits.
•TA78/DT5C144E (TR Array)
Diagram showing the transistor array configuration.
•LA1247 (AM Tuner IC)
Block diagram and terminal functions for the AM Tuner IC, including RF, MIX, IF, AGC, Detector, and Buffer circuits.
•TA76 (TR Array)
Diagram showing the transistor array configuration.
•M5218L, M5220L (Audio Pre IC)
Block diagram and terminal functions for the Audio Pre-Amplifier IC.
•LC4966 (Quad Bi-lateral Switch IC)
Diagram showing the quad bi-lateral switch configuration and its terminal functions.
•LA3400 (MPX IC)
Block diagram and terminal functions for the MPX (Multiplex) IC, including FM AM Muting, PLL, and FM AM mute logic.
•TC9157P (PLL & Control IC)
Detailed block diagram and terminal functions for the PLL & Control IC, covering programmable counter, phase comparator, automatic search, IF offset, channel control, ROM, preset memory, tuning control, and various input/output signals.
•M51321P (Analog SW.)
Diagram showing the analog switch configuration and its terminal functions.
•µPC1282CA (AM Stereo Detector)
Block diagram and terminal functions for the AM Stereo Detector IC, including Synchronous Detector, Buffers, Limiter, and Gate circuits.
•TD6301AP (7-Segment Decoder IC)
Block diagram and terminal functions for the 7-Segment Decoder IC, used for displaying frequency information.
•Terminal Function of LSI-TD6301P
Detailed pin descriptions for the TD6301AP IC, explaining functions like L/D, Data, CK1/CK2, I/O, and segment outputs (a1-g1, a2-g2, a3-g3).
•TD6104P (Prescaler IC)
Block diagram and terminal functions for the Prescaler IC, used in frequency division.
•Terminal Function of LSI-TD6104
Detailed pin descriptions for the TD6104 IC, including OUT-2, OUT-1, PSC, Vcc, and GND.
•Terminal Function of LSI-TC9157P
Detailed pin descriptions for the TC9157P IC, covering functions like XT, FM/MW/LW band switching, manual/auto tuning, preset memory storage (STO), display data output (DATA), muting signal (MUTE), and various control inputs (E1, E2, STOP 1-3, Do-1/Do-2, TEST, FMIN, PSC, AMIN, INH, INT).
Circuit Board Layouts and Parts Lists
This section provides component layout diagrams and parts lists for various circuit boards.
4-5. F-4742 PLL Synthesizer & Control Circuit Board
Component Side Layout: Diagram showing the placement of components on the F-4742 board.
Parts List
| Parts No. | Stock No. | Description | Parts No. | Stock No. | Description |
|---|---|---|---|---|---|
| •Transistor | • Diode | ||||
| fQ1 | 46367001 | 2SA1115 | fD1 | 03117600 | 1S2473T77 |
| or 46367201 | 2SA1048 | or 46086000 | 1S1588TP-3 | ||
| or 48058601 | 2SA933S | fD2 | 03117600 | 1S2473T77 | |
| fQ2 | 46367101 | 2SC2603 | or 46086000 | 1S1588TP-3 | |
| or 46367301 | 2SC2458 | fD3 | 03117600 | 1S2473T77 | |
| or 48058801 | 2SC1740S | or 46086000 | 1S1588TP-3 | ||
| fQ3 | 46367101 | 2SC2603 | fD4 | 03117600 | 1S2473T77 |
| or 46367301 | 2SC2458 | or 46086000 | 1S1588TP-3 | ||
| or 48058801 | 2SC1740S | fD5 | 03117600 | 1S2473T77 | |
| fQ4 | 46367101 | 2SC2603 | or 46086000 | 1S1588TP-3 | |
| or 46367301 | 2SC2458 | fD6 | 03117600 | 1S2473T77 | |
| or 48058801 | 2SC1740S | or 46086000 | 1S1588TP-3 | ||
| fQ5 | 46367101 | 2SC2603 | fD7 | 03117600 | 1S2473T77 |
| or 46367301 | 2SC2458 | or 46086000 | 1S1588TP-3 | ||
| or 48058801 | 2SC1740S | fD8 | 03117600 | 1S2473T77 | |
| fQ6 | 46367001 | 2SA1115 | or 46086000 | 1S1588TP-3 | |
| or 46367201 | 2SA1048 | fD9 | 03117600 | 1S2473T77 | |
| or 48058601 | 2SA933S | or 46086000 | 1S1588TP-3 | ||
| fQ15 | 46719900 | DTC124 | fD10 | 03117600 | 1S2473T77 |
| fQ16 | 46367001 | 2SA1115 | or 46086000 | 1S1588TP-3 | |
| or 46367201 | 2SA1048 | fD11 | -03117600 | 1S2473T77 | |
| or 48058601 | 2SA933S | F-46086000 | 1S1588TP-3 | ||
| •FET | fD12 | 03117600 | 1S2473T77 | ||
| eFT1 | 46643501 | 2SK163-K2 | or 46086000 | 1S1588TP-3 | |
| or 46643502 | 2SK163-L1 | fD13 | 03117600 | 1S2473T77 | |
| or 46643601 | 2SK117-Y | or 46086000 | 1S1588TP-3 | ||
| or 46643602 | 2SK117-GR | fD14 | 03117600 | 1S2473T77 | |
| •IC | or 46086000 | 1S1588TP-3 | |||
| fIC1 | 46397400 | TC9157P | fD16 | 03117700 | 10E-2 |
| or 48128000 | TC9157AP | fD17 | 03117700 | 10E-2 | |
| fIC2 | 07225000 | TD6104P | fC10 | 46725600 | 3900μF 6.3V E.L. |
| fIC3 | 46530000 | TC4022BP | fC15 | 48103400 | 1μF 50V Ε.Β. |
| fIC4 | 46273100 | BA634 | fTC1 | 46437700 | Trimmer Capacitor 50pF |
| fX01 | 07237701 | Quartz Element HC-18/U |
4-4. F-4743 UP, DOWN SW. & Preset Memory Circuit Board
Component Side Layout: Diagram showing the placement of components on the F-4743 board.
Parts List
| Parts No. | Stock No. | Description | Parts No. | Stock No. | Description |
|---|---|---|---|---|---|
| eC37 | 46693600 | 2200pF 50V F.C. | OS1 | 46556400 | Push SW., TUNING MODE |
| eC39 | 46694000 | 3300pF 50V F.C. | OS2 | 46556400 | Push SW., FM IF BAND |
| eC48 | 46696000 | 0.022µF 50V F.C. | OS3 | 46556400 | Push SW., MODE (FM) |
| eC51 | 46694200 | 3900pF 50V F.C. | OS4 | 46556400 | Push SW., MODE (AM) |
| eC52 | 46696600 | 0.039µF 50V F.C. | OS5 | 46556400 | Push SW., METER RANGE |
| eC58 | 46702900 | 0.068µF 50V F.C. | •LED | ||
| eC59 | 46694200 | 3900pF 50V F.C. | sLD1 | 46176900 | TLS-123 |
| eC60 | 46694400 | 4700pF 50V F.C. | or 46470200 | SEL2210S | |
| eTC1 | 46437500 | Trimmer Capacitor 30pF | sLD2 | 46176900 | TLS-123 |
| eTC2 | 46437500 | Trimmer Capacitor 30pF | or 46470200 | SEL2210S | |
| eCF1 | 48129100 | Ceramic Filter SFG450C | sLD3 | 46176900 | TLS-123 |
| eCF2 | 46578100 | Ceramic Filter BFU-450C10N | or 46470200 | SEL2210S | |
| eT4 | 46266900 | Low Pass Filter 19/38 kHz | sLD4 | 46176900 | TLS-123 |
| eT1 | 46724200 | AM ANT Coil | or 46470200 | SEL2210S | |
| eT2 | 46724100 | AM OSC Coil | sLD5 | 46176900 | TLS-123 |
| eT5 | 46917900 | AM RF Coil | or 46470200 | SEL2210S | |
| eT3 | 46724300 | AM IF Coil | sLD6 | 46176900 | TLS-123 |
| eVR1 | 46634700 | 47ΚΩ S.V.R., AM Strength Signal adj. | or 46470200 | SEL2210S | |
| eVR2 | 46634700 | 47ΚΩ S.V.R., AM Stop Level adj. | sLD7 | 46176900 | TLS-123 |
| eVR3 | 46634000 | 3.3ΚΩ S.V.R., AGC adj. | or 46470200 | SEL2210S | |
| eVR4 | 46633500 | 4700 S.V.R., Phase Sifte adj. | sLD8 | 46176900 | TLS-123 |
| eVR5 | 48119300 | 100ΚΩ S.V.R., DC Off Set adj. | or 46470200 | SEL2210S | |
| eVR7 | 48118900 | 5ΚΩ S.V.R., VCO Off Set adj. | sLD9 | 46176900 | TLS-123 |
| eVR8 | 46634300 | 10ΚΩ S.V.R., Separation adj. | or 46470200 | SEL2210S | |
| •Transistor | sS1 | 48128900 | Push SW., FM/AM PRESET STATION | ||
| fQ17 | 46367101 | 2SC2603 | sS2 | 48128900 | Push SW., FM/AM PRESET STATION |
| or 46367301 | 2SC2458 | sS3 | 48128800 | Push SW., TUNING, PRESET SCAN, MEMORY | |
| or 48058801 | 2SC1740S | ||||
| •Diode | |||||
| fD18 | 03117600 | 1S2473T77 | |||
| or 46086000 | 1S1588TP-3 | ||||
| fVR1 | 46634500 | 22ΚΩ S.V.R., FM Auto Stop Level adj. | |||
| • Transistor | |||||
| AmQ5 | 03032301 | 2SB507V11AL | |||
| AmQ6 | 46367101 | 2SC2603 | |||
| or 46367301 | 2SC2458 | ||||
| or 48058801 | 2SC1740S | ||||
| mQ7 | 46367001 | 2SA1115 | |||
| or 46367201 | 2SA1048 | ||||
| or 48058601 | 2SA933S | ||||
| •IC | |||||
| AmIC2 | 48129000 | M5236L | |||
| AmIC3 | 46499800 | L78N09 | |||
| AmIC4 | 48065900 | M5278L56 | |||
| •Zener Diode | |||||
| AmDZ4 | 46116000 | 05Z24-Y | |||
| AmR15 | 46229000 | 100Ω 1/2W N.I.R. | |||
| AmR16 | 46229000 | 100Ω 1/2W N.I.R. | |||
| AmR20 | 46230600 | 2.2kΩ 1/2W N.I.R. | |||
| AmR21 | 46229400 | 220Ω 1/2W N.I.R. | |||
| OS8 | 48127100 | Slide SW., AM STEP (XX) |
4-11. F-4748 Protector Circuit Board
Component Side Layout: Diagram showing the placement of components on the F-4748 board.
Parts List
| Parts No. | Stock No. | Description | Parts No. | Stock No. | Description |
|---|---|---|---|---|---|
| kR39 | 46623100 | 100 2W Ν.I.R. | •IC | ||
| kR40 | 46623100 | 100 2W Ν.I.R. | A IIC1 | 46207600 | TA7317P |
| kC17 | 46696800 | 0.047μF 50V F.C. | • Diode | ||
| kC18 | 46696800 | 0.047μF 50V F.C. | ID3 | 03117700 | 10E-2 |
| •IC | ID4 | 03117700 | 10E-2 | ||
| A IIC1 | 46207600 | TA7317P | ID5 | 03117700 | 10E-2 |
| • Diode | A kR39 | 46623100 | 100 2W Ν.I.R. | ||
| ID3 | 03117700 | 10E-2 | kR40 | 46623100 | 100 2W Ν.I.R. |
| ID4 | 03117700 | 10E-2 | AkR41 | 46249700 | 2200 1W N.I.R. |
| ID5 | 03117700 | 10E-2 | IC3 | 48104200 | 220μF 6.3V Ε.Β. |
| A kR39 | 46623100 | 100 2W Ν.I.R. | IRL 1 | 07198400 | Relay |
| kR40 | 46623100 | 100 2W Ν.I.R. | IRL2 | 07198400 | Relay |
| AkR41 | 46249700 | 2200 1W N.I.R. | IRL3 | 1.1504300 | Relay |
| IC3 | 48104200 | 220μF 6.3V Ε.Β. | or 1-1-504301 | Relay LA2A-24B | |
| IRL 1 | 07198400 | Relay | OZ3 | 07203600 | 8P-Terminal, SPEAKERS |
| IRL2 | 07198400 | Relay | ApF1 | 07189100 | Fuse 5.0A 250V (S-X1130-XX) |
| IRL3 | 1.1504300 | Relay | ApF2 | 07188900 | Fuse 3.5A 250V (S-X1100-XX) |
| or 1-1-504301 | Relay LA2A-24B | A pF2 | 07189500 | Fuse 10A 250V (S-X1130-CSA) | |
| OZ3 | 07203600 | 8P-Terminal, SPEAKERS | A | 07189300 | Fuse 7A 250V (S-X1100-CSA) |
| ApF1 | 07189100 | Fuse 5.0A 250V (S-X1130-XX) | |||
| ApF2 | 07188900 | Fuse 3.5A 250V (S-X1100-XX) | |||
| A pF2 | 07189500 | Fuse 10A 250V (S-X1130-CSA) | |||
| A | 07189300 | Fuse 7A 250V (S-X1100-CSA) |
4-12. F-4750 Mic Amp. Circuit Board
Component Side Layout: Diagram showing the placement of components on the F-4750 board.
Parts List
| Parts No. | Stock No. | Description |
|---|---|---|
| •Transistor | ||
| gQ1 | 46367101 | 2SC2603 |
| or 46367301 | 2SC2458 | |
| or 48058801 | 2SC1740S | |
| gC6 | 46688700 | 4700pF 50V F.C. |
| gVR1 | 48140100 | 20ΚΩ(Α) V.R., MIC LEVEL |
| oJ1 | 46289100 | Jack, MIC |
4-13. F-4751 PRE OUT-POWER IN Terminal Board
Component Side Layout: Diagram showing the placement of components on the F-4751 board.
Parts List
| Parts No. | Stock No. | Description |
|---|---|---|
| oZ5 | 48072600 | 4P-Terminal, PREOUT-POWER IN |
4-14. F-4753 Video Circuit Board <S-X1130 only>
Component Side Layout: Diagram showing the placement of components on the F-4753 board.
Parts List
| Parts No. | Stock No. | Description |
|---|---|---|
| •Transistor | ||
| mQ8 | 46367101 | 2SC2603 |
| or 46367301 | 2SC2458 | |
| or 48058801 | 2SC1740S | |
| •IC | ||
| mlC5 | 46361500 | L78N12 |
| OS23 | 48128700 | Push SW., ANTENNA, MUL-TIDIMENSION, NOISE FILTER, MODE |
| OZ8 | 48072500 | 3P-Terminal, VCR-B |
4-15. F-4754 VCR-A & VDP Terminal Board
Component Side Layout: Diagram showing the placement of components on the F-4754 board.
Parts List
| Parts No. | Stock No. | Description | |||
|---|---|---|---|---|---|
| •Transistor | |||||
| rQ1 | 46719900 | DTC124 | |||
| rQ2 | 46367101 | 2SC2603 | |||
| or 46367301 | 2SC2458 | ||||
| or 48058801 | 2SC1740S | ||||
| rQ3 | 46367101 | 2SC2603 | |||
| or 46367301 | 2SC2458 | ||||
| or 48058801 | 2SC1740S | ||||
| rQ4 | 46367001 | 2SA1115 | |||
| or 46367201 | 2SA1048 | ||||
| or 48058601 | 2SA933S | ||||
| rQ5 | 46367101 | 2SC2603 | |||
| or 46367301 | 2SC2458 | ||||
| or 48058801 | 2SC1740S | ||||
| rQ6 | 46367101 | 2SC2603 | |||
| or 46367301 | 2SC2458 | ||||
| or 48058801 | 2SC1740S | ||||
| rQ7 | 46367101 | 2SC2603 | |||
| or 46367301 | 2SC2458 | ||||
| or 48058801 | 2SC1740S | ||||
| rQ8 | 46367101 | 2SC2603 | |||
| or 46367301 | 2SC2458 | ||||
| or 48058801 | 2SC1740S | ||||
| •IC | |||||
| rIC1 | 48056800 | LC4966 | |||
| rlC4 | 46078900 | M5218L | |||
| rlC10 | 48056700 | M51321P | |||
| •Diode | |||||
| rD1 | 03117600 | 1S2473T77 | |||
| or 46086000 | 1S1588TP-3 | ||||
| rD2 | 03117600 | 1S2473T77 | |||
| or 46086000 | 1S1588TP-3 | ||||
| rD3 | 03117600 | 1S2473T77 | |||
| or 46086000 | 1S1588TP-3 | ||||
| rD7 | 03117600 | 1S2473T77 | |||
| or 46086000 | 1S1588TP-3 | ||||
| rD8 | 03117600 | 1S2473T77 | |||
| or 46086000 | 1S1588TP-3 | ||||
| rC11 | 46696400 | 0.033µF 50V F.C. | |||
| rC17 | 48102800 | 0.1μF 50V Ε.Β | |||
| rC18 | 46696000 | 0.022µF 50V F.C. | |||
| rC19 | 46696000 | 0.022µF 50V F.C. | |||
| rL1 | 46167400 | Inductor 47μΗ | |||
| rVR1 | 48127300 | 100ΚΩ(Α) + 1ΚΩ(Β) V.R., FADER | |||
| rVR2 | 48127200 | 2ΚΩ(Β) V.R., SHARPNESS | |||
| rVR3 | 48128600 | 50ΚΩ(W) V.R., SOUND MIXING | |||
| OS21 | 46630800 | Slide SW., VCR-A MODE | |||
| OS22 | 46630800 | Slide SW., VDP MODE | |||
| oZ6 | 48127700 | 6P-Terminal, VCR-A | |||
| OZ7 | 48127600 | 4P-Terminal, VDP, MONITOR OUT |
4-16. F-4755 VIDEO AUDIO PLAY Component Side Terminal Board <S-X1100 only>
Component Side Layout: Diagram showing the placement of components on the F-4755 board.
Parts List
| Parts No. | Stock No. | Description |
|---|---|---|
| OS24 | 46630800 | Slide SW., VIDEO AUDIO PLAY MODE |
| OZ8 | 48127500 | 2P-Terminal, VIDEO AUDIO PLAY |
4-17. F-4749 PHONES Jack Board
Component Side Layout: Diagram showing the placement of components on the F-4749 board.
Parts List
| Parts No. | Stock No. | Description |
|---|---|---|
| oJ2 | 46289200 | Jack, PHONES |
Packing List & Accessory List
Packing List
| Parts No. | Stock No. | Description |
|---|---|---|
| 1 | 91167720 | Vinyl Bag |
| 2 | 47694800 | Styrofoam Packing (Right) |
| 3 | 47694700 | Styrofoam Packing (Left) |
| 4 | 47694300 | Carton Case (S-X1130-Silver Model) |
| 47694200 | Carton Case (S-X1130-Black Model) | |
| 47694500 | Carton Case (S-X1100-Silver Model) | |
| 47694400 | Carton Case (S-X1100-Black Model) |
Diagram shows a folded carton for packing.
Accessory List
| Stock No. | Description |
|---|---|
| 46051700 | FM Antenna |
| 46145700 | AM Loop Antenna |
| 07563000 | Antenna Holder |
| 48111100 | VHF Antenna Cord with connector (S-X1130 only) |
| 46961500 | Operating Instruction (S-X1130) |
| 46961600 | Operating Instruction (S-X1100) |
