Keilton Basic RM51 Remote Controller for Fixture Sensor

ការពិពណ៌នា

The RM51 Remote is used to program the configurations of the Keilton Basic sensors using infrared (IR) communications with the devices. It offers 6 default modes of configurations plus manual settings. Customer configurations can be created, saved, and then sent to each device, ensuring a rapid deployment.

លក្ខណៈពិសេស

• ការប្រើប្រាស់ថាមពលទាប។
• Infrared communication.
• Setting most of the Keilton Sensors G2.
• Custom Configurations can be saved to A, B, C, D, or For.
• 40′ maximum IR range.
• RML (included with new orders, available as an accessory for order), installed, will increase the IR range. (See table below)

លក្ខណៈបច្ចេកទេស

ព័ត៌មានបញ្ជាទិញ

គំរូ	ការពិពណ៌នា
RM51.A0	Basic Sensor Controller RM51
RM51.A1	Basic Sensor Controller RM51 With RML

Ordering Information – Accessories

គំរូ	ការពិពណ៌នា
RML	Extended IR range for commissioning

វិមាត្រ

ស្លាកផលិតផល

ការណែនាំពីចម្ងាយ

របៀប​អង្គ​ចងចាំ (Commissioning)
To begin commissioning, follow these steps:

1. Select a memory profile: A, B, C, D, or E.
2. The remote’s indicator lights will flash, indicating the currently saved settings.
3. Settings can be configured by pressing the appropriate buttons in the highlighted gray area of the remote (TRIM-LEVEL, SENSITIVITY, HOLD TIME, STANDBY DIM, STANDBY TIME, and PHOTOCELL). Review the selected settings and make changes as needed.
4. Point the remote at the desired luminaire and press “SEND.”
5. The luminaire will flash twice to confirm that he settings are saved. Changing a parameter in a memory profile will automatically override previous settings.
6. If configuring multiple luminaires, repeat steps 4 and 5 after selecting the configured memory mode.

E Mode allows for visual adjustment to choose the desired dimming level.

Daylight Harvesting (F Mode)
Continuous Adjustment Mode adjusts dimming levels based on daylight.

1. Point the remote at the desired luminaire and press “ON,” then press DIM+ or DIM- to adjust the dimming level.
2. Press “F.” The indicator lights on the remote will show the current saved settings. Note: Only TRIM-LEVEL, SENSITIVITY, and HOLD TIME can be selected for Daylight Harvesting settings
3. Review the selected settings and make changes as necessary. Press “SEND.”
4. If the configuration is successful, the luminaire will flash twice to confirm that the setting is saved. If configuring multiple luminaires, select the configured Daylight Harvesting settings, then follow steps 1, 2, and 3.

Additional Remote Functions

ON	វេន ON អំពូលភ្លើង។
បិទ	វេន បិទ អំពូលភ្លើង។
តេស្ត	The fixture enters the test mode and exits automatically after 5 minutes. The test mode parameters are configured as follows: Trim-level: 100%, ភាពរសើប៖ ខ្ពស់, ពេលវេលាកាន់៖ ឆ្នាំ ១៩៩០ Standby dim: 50%, ម៉ោងរង់ចាំ៖ ៣៦០០ ស។
កំណត់ឡើងវិញ	Trim= 100%, Sensitivity = ខ្ពស់។, T1 = 5 នាទី, Standby Dim = 30%, T2 = 60 នាទី, Photocell = បិទ.
DIM+/-	Press Dim+ or Dim- to adjust brightness in 0.5V increments. Hold the button for continuous ស្រអាប់
TRIM-LEVEL	Set the Maximum brightness.
ភាពរសើប	Set the motion sensitivity of the sensor ទាប៖50% / ខ្ពស់៖100%, បិទ៖ disable the motion detection function.
កាន់ម៉ោង	The duration that elapses without occupancy detection before transitioning to standby dim.
រង់ចាំឌីម	Select any standby dim level.
ប្រចាំ​ការ ម៉ោង	Standby time, when the time is set to “∞”, the daylight detection function is activated.
រូបថត	visible light threshold, the fixture is allowed to be turned on when it falls below the threshold ទាប៖5fc / ខ្ពស់៖20fc, កាល់: Collect the current visible light illuminance as the threshold, បិទ៖ disable PHOTOCELL function.
របៀប	Default configuration parameters for modes A ទៅ F.
ផ្ញើ	ផ្ញើការកំណត់ទៅឧបករណ៍ចាប់សញ្ញា។
លំនាំដើម គំរូក	Trim= 100%, Sensitivity = ទាប, T1 = 30 នាទី, Standby Dim = 50%, T2 = ∞, Photocell = កាល់.
លំនាំដើម ខ	Trim= 100%, Sensitivity = ទាប, T1 = 30 នាទី, Standby Dim = 50%, T2 = 15 នាទី, Photocell = កាល់.
លំនាំដើម C	Trim= 100%, Sensitivity = ទាប, T1 = 30 នាទី, Standby Dim = 50%, T2 = 15 នាទី, Photocell = បិទ.
លំនាំដើម D	Trim= 50%, Sensitivity = ទាប, T1 = 30 វិ, Standby Dim = 50%, T2 = 30 នាទី, Photocell = កាល់.
លំនាំដើម E	Manual Dimmer Mode, Trim 100%.
លំនាំដើម F	Daylight Harvesting, Trim= 50%, Sensitivity = ទាប, T1 = 15 នាទី.

ទាក់ទងមកយើងខ្ញុំ

• 7001 Columbia Gateway Drive, Suite 210, Columbia, MD 21046, USA
• T: +1 ៨៦៦-៤៤៧-២១៩៤ (M-F 9 am-5 pm ET)
• E: support@autani.com

សំណួរគេសួរញឹកញាប់

How do I change the memory profile ការកំណត់?

Select the desired memory profile on the remote and adjust settings as needed before pressing SEND to save

Can I configure Daylight Harvesting settings for multiple luminaires simultaneously?

No, you need to configure Daylight Harvesting settings for each luminaire individually using the F Mode on the remote.

What is the expected operation if the user sets Standby Time to something other than INFINITE?

moiton -> the intensity of ambient light is lower than the threshold set by the PC->turn on the light and dim to trim-level->t1 timeout->dim to standby dim ->t2 timeout->turn off the light.

If it does not turn OFF the fixture, why would Mode B and D use CAL as the default?

The ambient light intensity stored by CAL will serve as the threshold for turning on the lights, but it has no connection with the function of turning off the lights.

ឯកសារ/ធនធាន

Keilton Basic RM51 Remote Controller for Fixture Sensor [pdf] សៀវភៅណែនាំរបស់ម្ចាស់ RM51.A0, RM51.A1, RM51 Remote Controller for Fixture Sensor, RM51, Remote Controller for Fixture Sensor, for Fixture Sensor, Fixture Sensor

ឯកសារយោង

• សៀវភៅណែនាំអ្នកប្រើប្រាស់