FOXTECH RDD-25A 4-Channel Visual Payload Release and Drop Device

លក្ខណៈបច្ចេកទេស

• វិមាត្រផលិតផល 125 × 117 x 60 ម។
• ទំងន់ផលិតផល 430 ក្រាម។
• Interface Type SKYPORT V2
• Control Method PSDK System
• Power 20 W Operating Temperature – 20°C to 60°C
• Number of Channels 4 Control Mode Independent channel control; select any release index or one-key all release
• Control Range Same as the aircraft communication range Status
• Feedback Real-time feedback for each channel
• Mounting Method Gimbal and belly mounting P HUB
• Supported Payload Capacity 2.5 kg per channel Video Resolution 1080P @ 30 fps

ផលិតផលលើសview

The RDD-25A device is a modular visual payload release system, consisting of one video capture module and one 4 -channel payload release module. The video capture module is mounted to the gimbal interface, transmitting downward video to the remote controller. The payload release module is mounted under the drone body and connected to the video module via a Type-C cable, sharing the drone’s PSDK interface. Each release unit can carry up to 2.5 kg of payload. The four units can be released sequentially or simultaneously.
អរគុណសម្រាប់ការទិញasing ផលិតផលរបស់យើង។
ប្រសិនបើអ្នកជួបប្រទះបញ្ហាណាមួយក្នុងអំឡុងពេលប្រើប្រាស់ សូមទាក់ទងអ្នកតំណាងផ្នែកលក់របស់អ្នកឱ្យបានទាន់ពេលវេលា។

ការបដិសេធ

ដោយគ្មានការអនុញ្ញាតជាលាយលក្ខណ៍អក្សរជាមុន គ្មានអង្គការ ឬបុគ្គលណាម្នាក់អាចដកស្រង់ ចម្លង ឬផលិតឡើងវិញនូវផ្នែកណាមួយ ឬទាំងអស់នៃសៀវភៅណែនាំនេះ ឬចែកចាយវាតាមទម្រង់ណាមួយឡើយ។
Due to product version upgrades or other reasons, the content of this manual may be updated periodically. This manual is for user guidance only. All statements, information, and recommendations in this manual do not constitute any express or implied warranty.

មាតិកាកញ្ចប់

ឈ្មោះ	បរិមាណ	ឯកតា
RDD-25A	1	កំណត់
ម៉ូឌុលដែលមើលឃើញ	1	កំណត់
ប្រអប់វេចខ្ចប់	1	កំណត់
ayload Release Hook Ring	s                 12	បំណែក
វិញ្ញាបនបត្រនៃការអនុលោម	1	ដុំ

ការយល់ដឹងអំពី 4-Channel Visual Payload Release និងទម្លាក់ឧបករណ៍

ការដំឡើងឧបករណ៍

1. Step 1: Turn the drone upside down and remove the two screws at the bottom of the gimbal.
2. Step 2: Confirm the connection position between the alloy bracket and the drone. To better fit the drone body, the bottom of the alloy bracket is slanted and one side has a groove. During installation, align the bottom of the alloy bracket with the drone body, with the grooved side facing outward.
3. Step 3: Insert one end of the alloy bracket into the middle of the connection point between the gimbal and the airframe, align the screw holes at both ends of the alloy bracket with the corresponding holes on the airframe, fasten the alloy bracket to the airframe at the gimbal-connection side using the supplied M3*10 screws, and fasten the other end using the supplied M3*8 screws.
4. Step 4: Connect the mounting plate to the alloy bracket, with the cable outlet facing the nose of the aircraft; adjust the exact mounting position of the plate as needed for actual use, and fasten the mounting plate to the alloy bracket using the supplied M3*8 screws.
5. Step 5: Connect the device’s power pickup to the mounting plate’s power port. Make sure the groove on the power pickup is aligned with the power port. After insertion, confirm that the quick-release latches on both sides have fully popped out before normal use (depending on the purchased version, connect the mounting plate interface to the HUB or to the aircraft’s E-PORT).
6. Step 6: Insert the connector of the payload release and drop device into the corresponding interface on the visual module.
7. Step 7: As shown in the figure, manually press the hook control button to set the hook into standby release mode. After connecting the matching metal ring to the payload, hang it on the hook.

ប្រតិបត្តិការឧបករណ៍

ប៊ូតុង PSDK៖ ចុចតែមួយដងដើម្បីបើក/បិទ 4-Channel Payload Release និងទម្លាក់ម៉ឺនុយប្រតិបត្តិការឧបករណ៍

ការពិពណ៌នាអំពីប៊ូតុងប្រតិបត្តិការ

ការត្រួតពិនិត្យបន្ទុក

Open the Payload settings; you can also operate the 4-Channel
Payload Release and Drop Device through this menu (tap the menu icon in the upper-right corner of the remote controller ដើម្បីបញ្ចូលការកំណត់ Payload) ។
Display real-time data switch: Show/Hide the working status and detailed information of the 4-Channel Payload Release and.

ទម្លាក់ឧបករណ៍
ចុចតែមួយដងដើម្បីដោះសោ/ចាក់សោ។ បន្ទាប់ពីដោះសោ ឧបករណ៍អាចដំណើរការជាធម្មតា

1. Hook 1: ចុចមួយដងដើម្បីចេញផ្សាយ
2. Hook 2: ចុចមួយដងដើម្បីចេញផ្សាយ
3. Hook 3: ចុចមួយដងដើម្បីចេញផ្សាយ
4. Hook 4: ចុចមួយដងដើម្បីចេញផ្សាយ

ប៊ូតុងបិទបើកទាំងអស់៖ ចុចតែមួយដងដើម្បីបញ្ចេញ

ការដោះស្រាយបញ្ហា

1	គ្មានរូបតំណាងគ្រប់គ្រង PSDK ទេ។	Check whether the wiring is correct. For the M350 version, plug into the top E-PORT of the aircraft and pay attention to the connector orientation. For the M300 version, connect to the supplied adapter ring and plug into the gimbal. For the visual version, connect the Type-C cable to the visual module and install the visual module on the gimbal.  Check the drone and remote controller firmware; they must be updated to the latest version.
2	ការបង្ហាញរូបតំណាង PSDK មិនពេញលេញ	Close the Pilot2 flight app in the background and re-enter, or restart. Check the drone and remote controller firmware; they must be updated to the latest version.

ចំណុចប្រទាក់ខាងក្រៅឧបករណ៍

• ចំណុចប្រទាក់ផ្នែករឹង៖ គ្មានសម្រាប់ផ្នែករឹងភាគីទីបីទេ។
• ចំណុចប្រទាក់ពិធីការកម្មវិធី៖ គ្មាន

ឯកសារ/ធនធាន

FOXTECH RDD-25A 4-Channel Visual Payload Release and Drop Device [pdf] សៀវភៅណែនាំអ្នកប្រើប្រាស់ FT100P-A, RDD-25A 4-Channel Visual Payload Release and Drop Device, RDD-25A, 4-Channel Visual Payload Release and Drop Device, Visual Payload Release and Drop Device, Payload Release and Drop Device, Release and Drop Device

ឯកសារយោង

• សៀវភៅណែនាំអ្នកប្រើប្រាស់