C PROX Disabled Toilet Locking System សៀវភៅណែនាំអ្នកប្រើប្រាស់

If a normally locked system, check the external keyswitch is in the locked position and the break glass isn’t pressed.
Link out the door switch terminals on the control board.

If this works, check mag lock reed switch/monitoring wiring and armature plate alignment.
Mag lock must give a normally closed signal when the door is shut.

a: តំណភ្ជាប់

With the door switch terminals still linked, momentarily short the C & N.O terminals for the internal lock sensor. If the LEDs change state every time you momentarily short the terminals, the problem is the wiring between the internal lock/open sensor and the WCPCB (break on a wire or incorrect wiring).
If problem persists, contact us for a new WCPCB.

a: តំណភ្ជាប់
b: Momentarily link

ឧបករណ៍ចាប់សញ្ញាប៉ះមិនបញ្ចេញសំឡេងនៅពេលប៉ះ

បន្ទាប់ពីជំហាននីមួយៗខាងក្រោម សូមផ្តាច់ថាមពលប្រព័ន្ធរយៈពេល 10 វិនាទី ហើយបើកវាឡើងវិញ។

Screw the sensor to the wall properly, don’t have it dangling or in your hand.
Ensure the jumper next to the touch sensor relay is on and is making properly.

Use a multimeter to check you’ve got voltage at the touch sensor. (Measure across +V red and 0V black). Note: Just because the LEDs are lit doesn’t mean there’s power to the touch sensor side of the board, they’re powered independently.
Make sure 0V is in the correct terminal, not the REM terminal.

Take off the wall and connect power only directly to the power supply on a short piece of cable to rule out any cable issues.

ប្រព័ន្ធចាក់សោដោយគ្មាននរណាម្នាក់នៅខាងក្នុង

Ensure the mag lock contacts are wired into the door switch terminals on control board.

Adjust the potentiometer on the internal touch sensor so that it switches for 3 - 5 seconds.
Turn down the sensitivity on the internal touch sensor, especially if there is emergency lighting or hand dryers nearby.

Make sure there isn’t excess cable in the touch sensor back box.
Re-terminate internal touch sensor connections.
Consider fitting the MULTI-TIMER reset relay.

ទ្វារស្វ័យប្រវត្តិមិនបើកនៅពេលដែលវាគួរ

Take the two wires to your automatic door operator out of the C and NO door activation terminals on the control board and join them together. If the door still doesn’t open, then the problem lies with the operator. Please contact the supplier/manufacturer.

ប្រព័ន្ធមានពណ៌ក្រហម ប៉ុន្តែ mag lock មិនភ្ជាប់ទេ។

Check the position of the override keyswitch in the external sensor.
Check the break glass hasn’t been pressed.
Check the lock fuse.
Link out the NC & KS/BG terminals on the control board. If it works with the link in, and your keyswitch and breakglass are in the correct position, then you have a break in the cable somewhere.

Use a multimeter to check if you’ve got voltage នៅ mag lock ។ ប្រសិនបើអ្នកធ្វើដូច្នេះ សោគឺមានបញ្ហា។

អំពូល LED ឧបករណ៍ចាប់សញ្ញាប៉ះមិនភ្លឺទេ។

Check the solid/flashing LED jumper on the control board hasn’t come off.

If you have square sensors, the LED wires connect to the larger outer PCB, see page 10 of the manual.
ប្រើ multimeter ដើម្បីពិនិត្យមើលវ៉ុលtage across the touch sensor LED terminals. Note that the LEDs have a separate supply to the touch sensor part, just because the sensor is beeping doesn’t mean you have voltage ទៅ LEDs ។ ប្រសិនបើមិនមានវ៉ុលទេ។tage, then you have a break on the cable.

Take sensor off the wall and connect it directly to the control board on a short piece of cable to rule out any cable issues.

អំពូល LED របស់ឧបករណ៍ចាប់សញ្ញាប៉ះកំពុងបញ្ចេញពន្លឺ ប៉ុន្តែខ្ញុំចង់ឱ្យពួកវាភ្លឺខ្លាំង

ផ្លាស់ប្តូរទីតាំង jumper នៅលើផ្ទាំងបញ្ជា។

ទ្វារចាក់សោឡើងវិញភ្លាមៗបន្ទាប់ពីដោះសោ

Adjust the potentiometer on the internal touch sensor so that it switches for 3 5 seconds.

This can be caused by the mag lock contact going open and closed circuit while the internal touch sensor is still beeping.
Check the armature alignment and that the door is not juddering when opening. · If necessary, replace the mag lock or fit a standard magnetic door contact instead.

តើវាអាចមានឧបករណ៍ចាប់សញ្ញាប៉ះខាងក្នុង ឬខាងក្រៅច្រើនជាងមួយទេ?

Yes, you can have multiple Door Assist or Touch to Lock/Open sensors, just wire them in parallel.

ឯកសារ/ធនធាន

ប្រព័ន្ធចាក់សោបង្គន់បិទ C PROX [pdf] សៀវភៅណែនាំអ្នកប្រើប្រាស់
ប្រព័ន្ធចាក់សោបង្គន់ពិការ ប្រព័ន្ធចាក់សោបង្គន់ ប្រព័ន្ធចាក់សោ

ឯកសារយោង

សៀវភៅណែនាំអ្នកប្រើប្រាស់

C PROX Ltd (Inc Quantek)

ប្រព័ន្ធចាក់សោបង្គន់បិទ ការដោះស្រាយបញ្ហា & សំណួរគេសួរញឹកញាប់

ឧបករណ៍ចាប់សញ្ញាខាងក្នុងនឹងប៊ីបនៅពេលប៉ះ ប៉ុន្តែមិនចាក់សោប្រព័ន្ធទេ។