មគ្គុទ្ទេសក៍កម្មវិធីគ្រប់គ្រងកម្មវិធីជំនួយ Auri Q-Sys មគ្គុទ្ទេសក៍អ្នកប្រើប្រាស់
ប្រវត្តិកំណែ
| Auri TX2N 1.0.0.4 | ខែសីហា ឆ្នាំ 2025 | Initial Release |
| Auri D4/D16 1.0.0.1 | ខែសីហា ឆ្នាំ 2025 | Initial Release |
ភាពឆបគ្នា។
The Auri TX2N plugin works with Auri TX2N and Auri TX2N-D Transmitters.
The Auri Docking Station plugin works with Auri D4 and Auri D16 Docking Stations.
Devices must be on firmware version 1.5 or above to support the plugin.
For each device, the API must be enabled before attempting connection with the plugin. The API is disabled by default and must be enabled via the Settings page of each device in Auri Manager. See the system manual for more details on how to configure your device.
Settings Config
| អាសយដ្ឋាន IP | Enter the IP address of the device to connect. This can be retrieved by checking the device listing page in Auri Manager. |
| ស្ថានភាព | Reports plugin and driver status. |
| Device Type* | Reports the device connected, TX2N, TX2N-D, D4 or D16. |
| Device Name* | Reports the name of the device connected. |
| Serial Number* | Reports the serial number of the device connected. |
| MAC Address* | Reports the MAC address of the device connected. |
| Software Version* | Reports the firmware version of the device connected. |
| Meter Rate (TX only) | Set how often the signal meters are polled in seconds (0.5 to 120). |
| Control Rate | Set how often other controls are polled in seconds (5 to 120). Use these options to balance responsiveness of any controls shown on a UI against the level of network traffic needed. |
| កំណត់អត្តសញ្ញាណ | Sends the identify command to flash the device LED for 30s. |
| Key Length (TX only) | Defines the length of randomized key to be generated, between 4-16 characters. Shorter keys should only be used when users will need to enter the key manually, for higher security when using RX1 receivers and QR codes the full 16 characters are recommended. |
| Key Type (TX only) | Defines the character set of randomized key to be generated, numbers, letters, alphanumeric or extended ASCII (adds a range of sup- ported special characters). The larger character set used the higher the security. As with key length this should be balanced with ease of use if manual entry is required. |
These fields will be populated for any online Auri device, regardless of whether the API is enabled or not.
Inputs (TX only)
| Stream 1 Input 1 Mute | Mutes the local inputs (analogue or Dante) to stream 1. |
| Stream 1 Input 2 Mute | Mutes the network audio inputs to stream 1. |
| Stream 1 Signal L/R | Reports back the signal level (post mix) for stream 1, between -96dB and 0dB. |
| Stream 2 Input 1 Mute | Mutes the local inputs (analogue or Dante) to stream 2. |
| Stream 2 Input 2 Mute | Mutes the network audio inputs to stream 2. |
| Stream 2 Signal L/R | Reports back the signal level (post mix) for stream 1, between -96dB and 0dB. |
Output 1/2 (TX only)
| Radio Output | Toggles the radio output on or off. |
| Broadcast Name | Sets the name for that broadcast, changing this will restart the radio. |
| Program Info | Sets the descriptive contextual information about the broadcast. |
| ការអ៊ិនគ្រីប | Toggles the encryption on or off for the broadcast. |
| Privacy Key | Sets the privacy key to be used if encryption is enabled. |
| Regenerate Key | Generates a new randomized privacy key based on the options set on the Config tab. |
| QR Code | Shows a QR code to allow Auracast assistants to connect devices to the broadcast. This includes the Broadcast Name, and if Encryption is enabled and a Privacy Key is set, the key will also be included. |
Library 1-16 / 17-32 (D only)
| Broadcast Name (1-32) | Allows broadcast name to be populated for each of the 32 entries in the docking station library, to be transferred to docked RX1 receivers. |
| Privacy Key (1-32) | Allows privacy key to be populated for each of the 32 entries in thedocking station library, to be transferred to docked RX1 receivers. |
ស្ថានភាពលទ្ធផល
| ស្ថានភាព | សារ | អត្ថន័យ |
| បាត់ | No IP | IP address field is blank. |
| INITALIZING | ការភ្ជាប់ | Plugin is establishing initial connection to the device. |
| INITALIZING | Testing API… | Successful initial connection has been made, establishing if API is enabled and responding. |
| OK | បានភ្ជាប់ | Device is responding to commands and reporting a valid system status. |
| កំហុស | Invalid IP | IP address is not valid. |
| កំហុស | Unsupported device type: | Device has responded but is not supported by the plugin, ensure you are using the correct plugin for TX2N or D4/ D16. |
| កំហុស | Device Error Code: X | Device is in an error state, consult the user manual and Auri Manager to resolve. |
| កំហុស | Device Offline / NoResponse | No response from the provided IP address. Check IP address and ensure device has power and network connectivity. |
| កំហុស | API Not Enabled | Device initial response received but no response from API.Check firmware version and API setting in Auri Manager. |
| កំហុស | Cannot create JSON UDP socket – try different IP or restart | Plugin is unable to open a UDP socket to the device on port55666. Check network configuration. |
| កំហុស | JSON service error – change IP to reconnect | Invalid response from the device’s info service, check AuriManager to confirm device is responding as expected. |
| កំហុស | Invalid JSON response | Invalid response from the device’s info service, check AuriManager to confirm device is responding as expected. |
| កំហុស | Cannot create UDP socket – try different IP or restart | Plugin is unable to open a UDP socket to the device for API on port 54666, confirm device firmware is up to date and API enabled, check network configuration. |
| កំហុស | UDP socket lost – change IP to reconnect | Connection has been interrupted, change the IP address orrestart the plugin to reinitialize the connection. |
| កំហុស | Network error – change IP to reconnect | Connection has been failed, change the IP address orrestart the plugin to reinitialize the connection. |
ទ្រព្យសម្បត្តិ
| Show Debug | Enables debug window. Dev only. |
| Debug Print | Selects which plugin actions should print to debug window. Dev only. |
User Interface – TX2N
User Interface – D4 / D16
ការតភ្ជាប់គ្នា Plugins
នេះ។ plugins expose all key elements as control pins, allowing you to connect them up to other parts of your Q-Sys design. One key use case is to ensure changes to the TX2N broadcasts are kept in sync with the Docking Stations, so that all docked receivers are able to connect.
AMPអ៊ីត្រូនិក Unit 2, Trentside Business Village, Farndon Road, Newark NG24 4XB, United Kingdom
ទូរស័ព្ទ៖ +44.1636.610062 www.ampetronic.com
បច្ចេកវិទ្យាស្តាប់ ១៥៥១ ហឺរីtage Crest Way, Bluffdale, Utah 84065-4818 សហរដ្ឋអាមេរិក
ទូរស័ព្ទ៖ + 1.801.233.8992
ឥតគិតថ្លៃ៖ 1.800.330.0891
www.listentech.com
ឯកសារ/ធនធាន
 |
Auri Q-Sys Plugin Guide Manager Software [pdf] ការណែនាំអ្នកប្រើប្រាស់ TX2N, D4, D16, Q-Sys Plugin Guide Manager Software, Plugin Guide Manager Software, Manager Software |