AAON CommLink 6 Transfer Communication Controller

លក្ខណៈបច្ចេកទេស

• ឆបគ្នាជាមួយ VCCX-454 ស៊េរី
• ឆបគ្នាជាមួយស៊េរី VCCX/VCCX-IP
• CommLink 6 Technical Guide
• Product Name: CommLink 6
• Part Description: AAON Unit Controllers, MiniLink PD 5, E-BUS Cable Assembly

COMMLINK 6 មគ្គុទ្ទេសក៍បច្ចេកទេស
ការពិនិត្យឡើងវិញ និងកាលបរិច្ឆេទ	ផ្លាស់ប្តូរ
Rev. A ថ្ងៃទី ១៥ ខែ សីហា ឆ្នាំ ២០២៤	ការចេញផ្សាយដំបូង
Rev. B ថ្ងៃទី 30 ខែសីហា ឆ្នាំ 2024	បានបន្ថែមព័ត៌មានការកំណត់រចនាសម្ព័ន្ធ IP បច្ចុប្បន្នភាពគ្រឿងសំអាង
Rev. C ថ្ងៃទី 22 ខែតុលា ឆ្នាំ 2024	បានបន្ថែមព័ត៌មានការកំណត់រចនាសម្ព័ន្ធ CommLink សម្រាប់ Windows® 10 និងក្រោយ
Rev. D, May 16, 2025	Updated Single and Multiple Loop Diagrams, clarified connection setup instructions

ឈ្មោះផលិតផលយោងផ្នែក
ការពិពណ៌នាផ្នែក	PART NUMBER
ឧបករណ៍បញ្ជាអង្គភាព AAON	ប្រែប្រួល
មីនីលីង PD ៥	ASM01626
E-BUS Cable Assembly E-BUS Power & Comm 1.5 ft., 3 ft., 10 ft., 25 ft., 50 ft., 75 ft., 100 ft., 150 ft., 250 ft., និង 1000 Foot Spool	G029440 (1.5 ft.), G012870 (3 ft.), G029460 (10 ft.), G045270 (25 ft.), G029510 (50 ft.), G029530 (75 ft.), G029450 (100 ft.), G029470 (150 ft.), V36590 (250 Ft.), G018870 (SPOOL)

ព័ត៌មានទូទៅ

ជាងview និងតម្រូវការប្រព័ន្ធ

ASM07420 CommLink 6 ត្រូវបានប្រើដើម្បីផ្ទេរទំនាក់ទំនងរវាងឧបករណ៍បញ្ជា ឬរង្វិលជុំក្នុងតំបន់នៅលើប្រព័ន្ធគ្រប់គ្រងរបស់អ្នក។ វាក៏អាចប្រើជាចំណុចប្រទាក់សម្រាប់ភ្ជាប់កុំព្យូទ័រទៅប្រព័ន្ធរបស់អ្នក។
CommLink 6 ផ្តល់ការប្រាស្រ័យទាក់ទងជាមួយប្រព័ន្ធគ្រប់គ្រងតាមរយៈកុំព្យូទ័រណាមួយដែលកំពុងដំណើរការកម្មវិធី Prism 2 ។
The CommLink 6 communication interface provides TCP IP Internet and/or intranet connection for Ethernet networked computer systems or USB directly connected to a PC, providing communication with the connected system.
Using standard TCP/IP Protocol, with AAON’s Prism 2 software, you are able to monitor and configure your controllers without a modem or a direct connection from a PC. Utilizing existing routers, proxies, or firewalls allows a PC running Prism 2 to connect to a controller in a remote accessible location or building. Several IP connection profiles អាចត្រូវបានបង្កើតឡើងដើម្បីជួយសម្រួលដល់ការត្រួតពិនិត្យឧបករណ៍ CommLink 6 ជាច្រើន។

ព្រមាន៖ ផ្ទៀងផ្ទាត់ខ្សែភ្លើងត្រូវនឹងការពិពណ៌នាបន្ទះខាងក្រោយ ដើម្បីបញ្ជាក់ថាបន្ទាត់រាងប៉ូលគឺត្រឹមត្រូវនៅពេលដែលខ្សែភ្លើង 24 VAC ទៅកាន់ប្លុកស្ថានីយថាមពល CommLink ឬការខូចខាតធ្ងន់ធ្ងរចំពោះផលិតផលនឹងកើតឡើង។

តម្រូវការប្រព័ន្ធ

ធាតុស្តង់ដារ (ទាមទារ)

• CommLink 6 ជាមួយខ្សែ USB និងអាដាប់ទ័រថាមពល (បានផ្គត់ផ្គង់)
• កុំព្យូទ័រដែលមានច្រកទំនាក់ទំនងអ៊ីសឺរណិត ឬច្រក USB (ផ្គត់ផ្គង់ដោយអ្នកផ្សេងទៀត)
  • See the SETUP section for additional information.
• Microsoft Windows® 10 or later (must be installed on the computer you are going to use)
• កម្មវិធី Prism 2 (អាចទាញយកបានដោយឥតគិតថ្លៃពី www.aaon.com)

ធាតុស្រេចចិត្ត
MinkLink PD ៥

ចំណាំ៖ AAON Controls Support cannot troubleshoot internal PC and/or Windows®-based operating system problems or building networks..

ការដំឡើង

មគ្គុទ្ទេសក៍ចាប់ផ្តើមរហ័ស

ចំណាំ៖ ប្រសិនបើអ្នកកំពុងប្រើ CommLink 6 ដោយមិនប្រើ Prism 2 អ្នកត្រូវអនុវត្តជំហាន 1-3 ប៉ុណ្ណោះ។

ជំហាន 1: Set your CommLink’s Loop switch to Multiple or Single. .

• ច្រើននៅពេលដែលមាន CommLink 6 តែមួយជាមួយនឹង MiniLink PD 5 យ៉ាងហោចណាស់មួយដែលបានដំឡើងនៅក្នុងប្រព័ន្ធ។
• នៅលីវនៅពេលដែលមាន CommLink 6 តែមួយដែលមិនមានម៉ូឌុល MiniLink PD5 ដែលបានតភ្ជាប់។

ជំហាន 2: Set your CommLink’s Baud rate switch to High or Low

• All devices connected on the buss need to be the same baud rate.
• VCCX2, VCCX-IP, VCCX-454, and GPC-XP are capable of communicating high or low speed.
• Older generation, VCM, VCMX, and GPC are only capable of communicating low speed.
• Refer to the individual controllers technical guide for baud rate settings.

ជំហានទី 3: Wire your CommLink to the appropriate controller on your system, and plug the CommLink into a power supply.

• Multi-Loop: A single daisy chain of MiniLinks
• Single Loop: A single daisy chain of controllers

ជំហាន 4: Install Prism 2 software on your computer.

ព្រមាន៖ If you are replacing an earlier version  of the CommLink with a CommLink 6, ensure the R(+) and T(-) terminals on the communications terminal block are wired the same as the back plate instructions. Incorrect wiring could lead to damage of the equipment.

ចំណាំ៖ AAON Controls Support cannot troubleshoot internal  PC and/or Windows®-based operating system problems, firewalls, routers, and/or problems on a customer’s internal or external network. An IT professional may need to be consulted.

ការតភ្ជាប់ និងខ្សែភ្លើង

បណ្តាញខ្សែតែមួយ RS-485 រង្វិលជុំ

បណ្តាញជាច្រើនខ្សែ RS-485 រង្វិលជុំ

រៀបចំ

កំពង់ផែ COM

ស្វែងរកលេខច្រក COM ដែល CommLink 6 កំពុងប្រើ (Windows® 10)

ជំហាន 1: Ensure CommLink 6 is connected to PC using a USB cable.
ជំហាន 2: Right-click on the Windows® icon, located on the bottom left or top left of the Windows Tool Bar or by using the search bar and typing Device Manager. ជំហាន 3: Select <Device Manager>.
ជំហាន 4: Click on the plus sign next to Ports to see all of the
common ports.
ជំហាន 5: Locate the USB Serial Port (COM#). The COM# in parentheses is the port it is located on. Write this COM port number down. You will need to know this when setting up the Prism 2 software.
ជំហាន 6: If the COM port number is 10 or greater, go to “Changing the USB COM Port Number” in the Troubleshooting section.

ការផ្លាស់ប្តូរលេខច្រក USB COM
When the CommLink 6 is first connected to a PC, Windows will assign a COM port number to be used for communicating with the Prism 2 software. If the port number is 10 or greater, it needs to be changed to a value less than 10 to be recognized by Prism 2.

ជំហាន 1: Right-click on the Windows® icon and select <Device Manager> to get to the Device Manager Window.

ជំហាន 2: Click on the plus sign next to Ports to see all of the COM ports.
ជំហានទី 3៖ Right-click on “USB Serial Port (COM#)” and select <Properties>. In the Properties Window, select the <Port Settings> tab.

ជំហាន 4: To assign a port number less than 10, click on <Advanced>. The Advanced Settings Window will appear.

ជំហាន 5:
In the COM Port Number drop box, select which COM port you wish to use. Make sure to select a COM port number that is not currently in use (the ports are listed in the Device Manager Window). Select a port number that is less than 10.

ចំណាំ៖ Windows® នឹងផ្តល់លេខច្រកទៅកាន់គ្រប់ឧបករណ៍ទាំងអស់ដែលធ្លាប់បានដំឡើងនៅលើកុំព្យូទ័ររបស់អ្នក។ ដូច្នេះប្រសិនបើមិនមានច្រកដែលមាននៅក្រោម 10 ទេ សូមជ្រើសរើសលេខច្រកតិចជាង 10 សម្រាប់ឧបករណ៍ដែលបានរាយបញ្ជីដែលអ្នកដឹងថាអ្នកមិនកំពុងប្រើបច្ចុប្បន្ន។

ជំហាន 6: Once you select the correct COM port number, click <OK> and close any windows opened in the process of changing the port number. Make note of this number because you will need it for your Prism 2 setup.

ព្រីម ១

ជំហាន 1: Open your Prism 2 software.
ជំហាន 2: Click the <Login> button and type in the Level 9 User Name and password (default is “admin, admin”). Click <Login>.

ជំហាន 3: If Prism 2 is online, click the<ON LINE> button to make it go <OFFLINE>. On initial startup, Prism 2 will not go online until a jobsite has been set up.

ជំហាន 4: Click on any empty location in the Job-Site Selection Window and then type in a job name in the Selected Location box and press <Enter>. Ensure you hit the enter key on keyboard to “Submit” or “Save” your change after typing.

ជំហាន 5: Click the <Job-Site> button to open the Job-Sites Window.

ជំហាន 6: In the Serial Port field, click on the pull down box and select the COM Port number that the CommLink 6 is using.

ជំហាន 7: In the Type of CommLink selection box, select the radio button next to CommLink 6.

ជំហានទី 8៖
In the Network Configuration selection box, select the type of system configuration you are using. The only options applicable to CommLink 6 are Multiple Loop Configuration (Network) or Single Loop Configuration.

ជំហានទី 9៖
Click <Exit> to close out of the Job Sites Window. After closing Job-site Editor, If the new job site name doesn’t appear in the Job-site list click on another job site or empty space to refresh the view.

ជំហាន 10: Select the job-site in the job-site list then click on the <ON LINE> Button .

ជំហាន 11: From the <Communications> menu, select <ស្វែងរក ឯកតា > ។

ជំហាន 12: នេះ។ ស្វែងរក Installed Units Window will pop up. Click <Start Search> located in the upper left-hand corner of the window to initiate an automatic detection of all installed controllers and MiniLinks on your system.

ជំហាន 13: If everything is working correctly, Units Found on this Loop should increase. You will also see green boxes indicating units that have been found..

ជំហាន 14: If Units Found on this Loop stays at zero, try the following options:

• Check the wiring to the CommLink 6 and the AHU/RTU Controllers
• Check to see if the Loop Light on the Commlink is flashing. If it is solid the Commlink is not talking to any device. If it is flashing it is at least talking to one device on the network.
• Read through these directions again to make sure all steps were followed.

ជំហាន 15: To stop a search, click <Cancel Search>.
ជំហាន 16: Once you are done searching for units, close out of the window or click <Exit>.
ជំហាន 17: A window will pop up that asks, “Do you want to save the search results?” Click <Yes> if you wish to save the results. Click <No> if not.
ជំហាន 18: You can now access any installed unit from the Main Prism 2 Screen by selecting a loop from the Loop Selection Window with a single-click and by selecting the unit from the Unit Selection Window with a double-click

Computer Static IP Configuration

ការដំឡើងអាសយដ្ឋាន IP កុំព្យូទ័រសម្រាប់ Windows® 10 និងក្រោយ។
Before you can communicate with the CommLink through the IP network port your computer and the CommLink IP addresses have to be within the same IP Network Scheme.

ជំហាន 1: Right click the Windows icon or <Start>; then click <Network Connections>.
ជំហាន 2: Then click <Network and Sharing Center>. The Network and Sharing Center Window will appear.
ជំហាន 3: In the Network and Sharing Center Window, select the Local Area Connection entry. The Local Area Connection Status Window will appear.

ជំហាន 4: Click the <Properties> button. The Local Area Connection Properties Window will appear.

ជំហាន 5: In the Connection Items List Box (Figure 9), be sure the Internet Protocol Version (TCP/IPv4) is checked. Click on Internet Protocol (TCP/IP v4) to highlight it and then click <Properties>. The Internet Protocol Properties Window will appear.

ជំហាន 6: Type in the following information:

• បង្កើតអាសយដ្ឋាន IP 192.168.1.5
• បង្កើតរបាំងបណ្ដាញរង 255.255.255.0
• បិទការកំណត់ច្រកចេញចូលលំនាំដើម (ទុកការកំណត់ឱ្យនៅទទេដូចបង្ហាញក្នុងរូបភាពទី 10)។
• Blank out the Preferred DNS server setting and the Alternate DNS server setting.

ជំហាន 7: Select <OK> until all of the above windows are closed.

ការកំណត់រចនាសម្ព័ន្ធបណ្តាញ IP

ជំហាន 1: Run the Prism 2 program, open the Job Sites Window, and type the default IP address 192.168.1.25 in the Node IP Address field. See the Prism 2 Technical Guide if needed for further instructions. To access the IP Module web ទំព័រ, ចុចលើ ផ្ទាំងហើយបន្ទាប់មកចុច Web ការកំណត់> (សូមមើលខាងក្រោម)។

ជំហាន 2: The Sign In Window, shown below, will pop up before you can have access to the CommLink IP Module Webទំព័រ។ ទុកឈ្មោះអ្នកប្រើប្រាស់ឱ្យនៅទទេ ហើយក្នុងវាលពាក្យសម្ងាត់ បញ្ចូលពាក្យសម្ងាត់ដែលមានទីតាំងនៅខាងក្រោមនៃ CommLink បន្ទាប់មកចុច .

ចំណាំ៖ If there is no password label on the bottom of your CommLink, open the CommLink and look at the IP Module label for the MAC Address. The MAC address is the 12 digit dashed alphanumeric number The password is 8500 plus the MAC address with no spaces or dashes. 

ជំហាន 3: The CommLink IP Module Window, shown below, will appear if a connection is established.

ជំហាន 4: Click <Network Configuration> found in the menu bar on the left side of the web ទំព័រ។

ជំហាន 5:
Under IP configuration, select the radio button in front of the option <Use the following IP configuration> and type in the IP address, Subnet Mask, and Default Gateway as provided by the jobsite IT staff.

ចំណាំ៖ Be sure all other settings are set to default.

ជំហាន 6: Click <OK> at the bottom of the Network Settings Screen once the changes have been made.
ជំហាន 7: Click <CommLink Configuration> found in the menu bar on the left side of the web ទំព័រ។

ជំហាន 8: Under Port Settings, in the Baud Rate drop down menu, select the appropriate baud rate and click OK.

ជំហាន 9: Click <Change Password> found in the menu bar on the left side of the web ទំព័រ។
ជំហាន 10: The Change Password Window will appear. Type in a  new password in both fields—the New Password field and Retype Password field and press <OK>. A message will appear if the password change is successful. Make sure to write the new password down.

ចំណាំ៖ If for some reason you forget or lose the password, you can press the reset button on the back of the CommLink (located next to the DIAG button). This will reset the password to the factory-set password and will also reset ALL factory settings. As a result, all factory settings will need to be reconfigured.

ជំហាន 11: After you are done modifying all of the IP settings, click <Apply Settings> in the menu bar to the left.

ជំហាន 12: To verify that the changes were successful, connect to the building’s network using a standard Ethernet cable. Then make sure your PC has a connection to the Local Area Network and reopen the IP Setup Webpage by typing in the newly assigned IP Address.

ជំហាន 13: Be sure to set the IP address in Prism 2 to the new IP address set up for the CommLink.

ដំឡើងពីចម្ងាយ

ជំហាន 1: Connect a crossover cable from the CommLink6 Ethernet port to the Ethernet port on your Windows laptop.
ជំហាន 2: Navigate to the “Control Panel” and click “Network and Sharing Center”.

ជំហាន 3: Here you will see the Ethernet port for the CommLink6 under “Active Networks”. Click the blue Ethernet link next to the “Connections:” label.

• If you are unsure which network is the crossover cable to the CommLink6, unplug the cable and plug it back in to watch it reappear.

ជំហាន 4: Click “Properties” and set the IP address to 192.168.1.24 and the Subnet Mask to 255.255.255.0

• This changed your laptop’s IP address only. It cannot yet talk with the CommLink6.

ជំហាន 5: Open Prism and click “Job Site” in the upper left corner of the screen.
ជំហាន 6: Set the Node IP Address to 192.168.1.25. Set the Serial Port to “No Port Selected”. This is the CommLink6’s default IP address. 

ជំហាន 7: Perform a “ស្វែងរក Units” to confirm they are communicating.

ជំហាន 8
Obtain the IP address, Subnet Mask, and Default Gateway of the building’s network.

ជំហានទី 9៖
Click “Communications” on the top left hand corner and select “CommLink IP Web ការកំណត់”។

ជំហានទី 10 : The sign in window will pop up before you can have access to the CommLink IP Webpage. Leave the Username blank, and in the Password field, enter the password located on the IP module. You will need to open up the CommLink to find this.

ជំហាន 11: The CommLink IP Window, shown below, will appear if a connection is established.

ជំហាន 12: Click “Network Configuration” found in the menu bar on the left side of the web ទំព័រ។

ជំហាន 13: Select the radio button “Use the following IP configuration:” and enter the building’s IP Address, Subnet Mask, and Default Gateway.

ជំហាន 14: Scroll down to the bottom of that same page. Click “OK” and then click “Apply Settings” on the menu bar. After clicking “Apply Settings”, WAIT. It will appear as if nothing has changed, but after 5-10 seconds it will load.

ចំណាំ៖ Issues may occur if attempting to access any other function before it has finished loading.

ការដោះស្រាយបញ្ហា

CommLink 6 អំពូល LED

យូអេសប៊ីយូអេសប៊ី

រង្វិលជុំ៖
បង្ហាញសកម្មភាពទំនាក់ទំនងនៅលើបណ្តាញឧបករណ៍បញ្ជាមូលដ្ឋាន។ LED នេះភ្លឹបភ្លែតៗនៅពេលដែលទិន្នន័យត្រូវបានផ្លាស់ប្តូរជាមួយបណ្តាញឧបករណ៍បញ្ជា។

USB TX៖ Indicates transmitted data status of USB connection. This LED only flashes when your CommLink 6 is connected to a computer and data is sent to Prism from the CommLink 6 via USB.

USB RX: Indicates received data status of USB connection. This LED only flashes when your CommLink 6 is connected to a computer and data is sent from Prism to the CommLink 6 via USB.

USB STAT: Indicates connection to your computer. This LED will turn on solid once you plug the USB cable into your computer as long as the connection is not lost.

បណ្តាញ LEDs

• ETH STAT: Indicates connection to your ethernet. This LED will turn on solid once you plug the ethernet cable into the CommLink 6 and remain lit as long as the connection is not lost.
• ETH TX: Indicates activity on the local area network. This LED flashes on when LAN is transmitting and receiving data and is only operational with an Ethernet connection.
• ETH RX: Indicates local area network is connected. This LED is on when connected to LAN and is only operational with an Ethernet connection.
• ETH LINK: Indicates wireless connection to the local area network. This LED flashes on when LAN is transmitting and receiving data and is only operational with an Ethernet connection.

ការតភ្ជាប់

ភាពឆបគ្នានៃប្រូកស៊ី និងជញ្ជាំងភ្លើង
ការកំណត់រចនាសម្ព័ន្ធប្រូកស៊ី និងជញ្ជាំងភ្លើងអាចក្លាយជាចាំបាច់នៅពេលដែល CommLink 6 ត្រូវបានភ្ជាប់ទៅ LAN/WAN ដែលត្រូវបានការពារដោយ Firewall ប្រូកស៊ី ឬរ៉ោតទ័រដែលបើក NAT ដែលអាចប្រើបាន។ ឧamples of these would include Cisco, NetGear, LinkSys, or WatchGuard Technologies. Also, some ISPs provide IP Address ranges that are already fire-walled at the NOC or ISP Head-End. Make sure that your IT Department or ISP can create a mapped TCP port 39288 on your firewall/proxy to TCP port 39288 on the assigned IP Address of the CommLink 6.
Only with proper configuration of the Firewall/Proxy are connections to the CommLink 6 from outside of the local area network going to be possible. Check that the Firewall/Proxy TCP port 39288 is not set to time out or reset after a specified amount of time when there is no traffic from the remote PC.

បញ្ហាជាមួយកម្មវិធី Prism 2
ផ្ទៀងផ្ទាត់ថាច្រក COM ត្រឹមត្រូវដែលបង្កើតឡើងដោយការភ្ជាប់ USB ត្រូវបានជ្រើសរើសនៅក្នុងបង្អួចគេហទំព័រការងារ។ ផ្ទៀងផ្ទាត់លេខច្រក COM ដោយចុចខាងស្តាំលើរូបតំណាង Windows® ដោយជ្រើសរើស , និង viewing .
ផ្ទៀងផ្ទាត់ថាប៊ូតុងវិទ្យុ ត្រូវបានជ្រើសរើសសម្រាប់ប្រភេទនៃ CommLink នៅក្នុងបង្អួចគេហទំព័រការងារ។
ផ្ទៀងផ្ទាត់ថារបៀប CommLink ត្រឹមត្រូវត្រូវបានជ្រើសរើសនៅក្រោមការកំណត់រចនាសម្ព័ន្ធបណ្តាញនៅក្នុងបង្អួចគេហទំព័រការងារ។ ជ្រើសរើស ឬ .

បញ្ហាជាមួយការភ្ជាប់ USB

• ផ្ទៀងផ្ទាត់ថា USB TX និង USB RX លោតភ្លឹបភ្លែតៗ នៅពេលអ្នកធ្វើ ស្វែងរក ឯកតា ឬព្យាយាមបើកអេក្រង់ស្ថានភាពនៅក្នុង Prism 2។
• ប្រសិនបើ LEDs USB បរាជ័យក្នុងការភ្លឹបភ្លែតៗ សូមផ្តាច់ និងភ្ជាប់ការភ្ជាប់ USB ឡើងវិញ។

Wrong Monitor Size
When Prism2 gets the wrong monitor size from the windows registry, it will not show the controller view. There is a thumbnail view when you hover over the Prism icon in the task bar that is all white.

ព័ត៌មានជំនួយ
AAON Controls ផ្តល់ការគាំទ្រការដំឡើង និងការកំណត់រចនាសម្ព័ន្ធ Prism 2។ ហៅ ៨៦៦-៤៤៧-២១៩៤ ដោយឥតគិតថ្លៃ ការគាំទ្រតាមទូរស័ព្ទដោយផ្ទាល់ ឬ ៨៦៦-៤៤៧-២១៩៤ ដើម្បីនិយាយទៅកាន់អ្នកតំណាងផ្នែកជំនួយគ្រប់គ្រង។ ការគាំទ្រសម្រាប់សេវាទូរស័ព្ទទាំងអស់គឺអាចរកបានពីថ្ងៃច័ន្ទដល់ថ្ងៃសុក្រពីម៉ោង 7:00 ព្រឹកដល់ 5:00 ល្ងាចម៉ោងស្តង់ដារកណ្តាល។

ចំណាំ៖ AAON Controls Support មិនអាចដោះស្រាយបញ្ហាកុំព្យូទ័រខាងក្នុង និង/ឬបញ្ហាប្រព័ន្ធប្រតិបត្តិការដែលមានមូលដ្ឋានលើ Windows® បានទេ។

ចំណាំ៖ AAON Controls Support មិនអាចដោះស្រាយបញ្ហាជញ្ជាំងភ្លើង រ៉ោតទ័រ និង/ឬបញ្ហានៅលើបណ្តាញខាងក្នុង ឬខាងក្រៅរបស់អតិថិជនបានទេ។ អ្នកជំនាញផ្នែកព័ត៌មានវិទ្យា ប្រហែលជាត្រូវការពិគ្រោះ។

AAON គ្រប់គ្រងការគាំទ្រ៖
៨៦៦-៤៤៧-២១៩៤
ថ្ងៃច័ន្ទ ដល់ថ្ងៃសុក្រ ម៉ោង ៧ៈ០០ ព្រឹក ដល់ ៥:០០ ល្ងាច ម៉ោងកណ្តាល

គ្រប់គ្រងការគាំទ្រ webគេហទំព័រ៖ www.aaon.com/aaon-controls-technical-support

ជំនួយបច្ចេកទេសរោងចក្រ AAON៖
៨៦៦-៤៤៧-២១៩៤ | techsupport@aaon.com

ចំណាំ៖ មុននឹងហៅទូរស័ព្ទទៅផ្នែកជំនួយបច្ចេកទេស សូមមានម៉ូដែល និងលេខស៊េរីនៃអង្គភាពដែលមាន។

ប្រធានបទ៖ សម្រាប់គ្រឿងបន្លាស់ សូមទាក់ទងអ្នកតំណាង AAON ក្នុងតំបន់របស់អ្នក។

• ២៤២៥ ដូច្នេះ។ វិថីយូកុន
• Tulsa យល់ព្រម
• ០១៤៨៦០៧៤-០០៤
• ភី៖ ៨៦៦-៤៤៧-២១៩៤
• ទូរសារ៖ ៨៦៦-៤៤៧-២១៩៤ ប
• បង្កើតឡើងនៅសហរដ្ឋអាមេរិក

© APRIL 2025 AAON All Rights Reserved

សំណួរគេសួរញឹកញាប់

• Q: Can multiple CommLink 6 devices be monitored simultaneously?
  A: Yes, several IP connection profiles can be created to facilitate monitoring several CommLink 6 devices using AAON’s Prism 2 software.
• Q: Where can I download the manual for the CommLink 6?
  A: The manual is available for download at www.aaon.com.

ឯកសារ/ធនធាន

AAON CommLink 6 Transfer Communication Controller [pdf] ការណែនាំអ្នកប្រើប្រាស់ VCCX-454 Series, VCCX-VCCX-IP Series, CommLink 6 Transfer Communication Controller, CommLink 6, Transfer Communication Controller, Communication Controller, Controller

ឯកសារយោង

• សៀវភៅណែនាំអ្នកប្រើប្រាស់