Kinan 3030108133G-KFP286K 4K Display Port IP KVM Matrix Extender

FAQs

• Q: What should I do if the extender is not functioning properly?
  • A: If you encounter any issues with the extender, first check the connections and power supply. Refer to the troubleshooting section in the user manual for further assistance. If problems\ persist, contact customer support for help.

User Information

Telephone Support

For telephone support, please call below number:

• TEL 0086‐755‐26755041
• MOBILE 0086‐13714411566

User Notification 

All information, documentation, and specifications contained in this manual are subject to change without prior notice. The manufacturer does not make any explicit or implied statement or guarantee about the contents of this document, especially for merchantability or fitness for any specific purpose. Any manufacturer’s equipment described in this manual is sold or licensed as it is. If the equipment is damaged artificially after purchase, the buyer (not the manufacturer, its distributor or reseller) shall bear all costs for necessary repair and any losses caused by equipment defects. If the correct operating voltage setting is not selected before operation, the manufacturer will not be responsible for any damage caused by the system operation. Please make sure the voltage has been set correctly before use.

Introduction

The KFP286K IP KVM matrix extenders are highly optimized KVM extenders. The point‐to‐point connection supports a transmission distance of 120m, and a resolution up to 3840×2160@60Hz. This series of extenders can be connected to a 1G network switch to form a matrix switching system, which supports point‐to‐point (P2P) mode and matrix (Matrix) mode. The matrix switching system composed of extenders supports up to 9999 nodes by using centralized management software, and it can support up to 40 nodes without using centralized management software. It can connect multiple signal sources (such as servers, workstations, cameras and video walls). With the matrix switching system, computers and servers can be located in the central server room far from the workstation to improve security, reduce the temperature and noise of the working environment, and achieve a quiet and friendly human‐computer interaction environment. The video compression algorithm of the KFP286K matrix extender is a perfect combination of high‐quality image and low latency (<8ms). The USB and video signals are transmitted through the CAT5e/6/7 network cable. It supports USB devices such as touch screens, USB sound card, printers, etc., it can also support USB storage devices.

Function

This product is intended to be used as a device to increase the distance that a keyboard, monitor and mouse can be placed from a computer. This product is intended for professional use. The product should not be used in potentially explosive environments. The product may only be used according to the instructions as described in this manual. All use, other than that described in this manual, is seen as unintended use. In this product, the product connected to the host end is called the transmitter (TX), and the product connected to the display end is called the receiver (RX).

Feature

• Display Port / USB2.0/Audio ‐ IP KVM Matrix Extender
• Dual screen version
• Point‐to‐point connection supports a maximum extension distance 120m/394ft
• Support seamless switching
• Freeze the last image after the disconnection of the transmitter and receiver
• Support resolution up to 3840×2160@60Hz (4:4:4)
• USB transmission rate up to 480Mbit/s
• Display Port lossless real‐time full HD transmission
• Support transmission through fiber optic and network (CAT5e/6/7)
• Support one Administrator account and one User account
• Support remote computer power on and off

Safety Instructions

WARNING! Read and understand all safety instructions.

• Please follow all instructions. This will avoid accidents, fire, explosions, electric shocks or other hazards that may result in damage to property and/or severe or fatal injuries. Please ensure that everyone who uses the product has read and followed these warnings
• Keep all safety information and instructions for future reference and pass them on to subsequent users of the product.
• The manufacturer is not liable for cases of material damage or personal injury caused by incorrect handling or non‐compliance with the safety instructions. In such cases, the warranty will be voided.
• The product is not allowed to use in potentially explosive environments.
• Check the product and the cables for any damage before use. If there is any visible damage, a strong odour, or excessive overheating of components unplug all the connections immediately and stop using the product.
• If the product is not installed and used in accordance with this manual, it may cause disruptive interference with radio or television reception or affect other electronic products in residential areas.
• Use shielded cables to connect components to avoid the above interference.
• Only the power adapter included with the product should be used as the power supply. Do not use other adapters.
• Make sure your local voltage matches the rating indicated on the product before powering on it.
• The product must be connected to a permanent and earthed AC wall socket.
• Protect cables from being strained, pinched or buckled and place them in a way to prevent people from tripping over the cord.
• Avoid any damage to the power adapter.
• Use the product with a suitable, properly installed and easily accessible power socket to make sure the product can be disconnected from the power socket at all times.
• Disconnect the product when not in use.
• Never touch the adapter with wet hands.
• Use the product within the specified performance limits.
• Keep the product away from any flammable materials like curtains.
• Protect the power adapter from use by third parties (particularly children).
• Keep the product away from heater.
• Do not drop or hit the product.

Product Overview

KFP286K receiver (TX)

KFP286K sender (RX)

Installation

Installation of Extender

Warning! Please read and be aware of all safety instructions before installing the equipment. The extender can be set as a point‐and‐point mode to access a single PC, and also can access multiple PCs through matrix switching system.

Matrix switching system

Connection Diagram of KFP286K

1. Make sure the KVM extender is grounded (See ① in the above diagram)
2. Connect the KFP286K_TX to the DisplayPort video port, USB port, and audio port of a computer. (See ② in the above diagram)
3. Connect the KFP286K_RX to the keyboard, mouse, monitor, and audio device. (See ③ in the above diagram)
4. Connect the transmitter and receiver interfaces via optical fiber or CAT5E cable. (See ④ in the above diagram)
5. Power on the transmitter and receiver. (See ⑤ in the above diagram)
6. Connect the USB peripheral to the receiver (KFP286K _RX) (See ⑥ in the above diagram)

Matrix Connection Diagram

Extender Configuration

Use of UI Interface

Press the left [Ctrl] key on the keyboard 3 times continuously, then the main UI interface will display.

[Name Setting of TX_List]

Double‐click the name of a TX, and then the following name setting window appears.

Function Name	Description
TX‐0234b3616d6b	Click to change the name of TX, and then click “ESC” button to confirm your modification.
Reboot	Reboot the device
Restore factory	Restore Factory Defaults
Bit Rate	Auto, 10M ,50M, 100M, 150M, 200M
Network mode	Multicast mode Unicast mode
Scan time	10s, 20s, 30s, 60s, 90s ,120s, 150s, 180s, 210s, 255s
Blink	To set PWR flashing time, check TX connection status. You can choose from “Close, 1 min, 10 min, 30 min, 60 min, always”.
EDID	AUTO, 1024×768, 1280×1024, 1366×768, 1600×900 , 1920×1080, 1920×1200, 2560×1440, 3840×2160, 1152×864, 2048×2048,1600×1200,1920×1920, 2160×2160, 2560 x1600, 3840 x1080, 4096 x1080, 2560 x2880
Secondary EDID	AUTO, 1024×768, 1280×1024, 1366×768, 1600×900 , 1920×1080, 1920×1200, 2560×1440, 3840×2160, 1152×864, 2048×2048,1600×1200,1920×1920, 2160×2160, 2560 x1600, 3840 x1080, 4096 x1080, 2560 x2880

[Auto Scan Setting]

Select TX devices, click the QV item, and then click “ ” to automatically scan the selected device (default scan time: 10s).

Scan time: 10s, 20s, 30s, 60s, 90s, 120s, 150s, 180s, 210s, 255s

[User Login Interface]

The default setting mode is “ ”(See User Setting on Page 18), the login interface will only appear after clicking the icon

[The list of matched TX/RX]

Click function key [ ], and then the following menu appears:

When you see the device name in the TX list and the RX list, that means that the TX and RX are matched successfully

Function Setting

Click the function key [ ], and then below menu appears:

Function Name	Description
Equipment Info	To switch on/off USB, Audio, KM, Get & Push
Equipment Setting	System and User Settings
Frame Push	Push the video and USB signals from current receiver to the chosen receiver in the list
Frame Get	Get the video and USB signals from any receiver in the list to the current receiver
Upgrade	Update device
Hotkey	Hotkeys of device

[Equipment Info]

Select [ ] to switch on/off the system state.

Function Name	Description
Usb2.0	USB2.0 function
Audio	Audio function
KM	Keyboard and Mouse
Share	Push video & Get video

[Equipment Setting]

Function Name	Description
RX‐8220785f097	Click to change the name of RX, and then click “ESC” button to confirm your modification.
All Blink	To set PWR flashing time You can choose from “Close, 1 min, 10 min, 30 min, 60 min, always”.
Reboot	Reboot device
Restore factory	Restore factory defaults
System mode	Matrix mode P2P mode Node mode
Network mode	Multicast mode Unicast mode
Edid Sync	AUTO, 1024×768, 1280×1024, 1366×768, 1600×900 , 1920×1080, 1920×1200, 2560×1440, 3840×2160, 1152×864, 2048×2048,1600×1200,1920×1920, 2160×2160, 2560 x1600, 3840 x1080, 4096 x1080, 2560 x2880
Output timing Secondary output	1080P@60, 2160P@60, 640 x 480P@60, 800x600P@60 1024 x 768P@60,1280 x1024P@60, 1366×768, 1440×900 , 1920×1200, STRICT PASS, AUTO PASS
Password mode	Modify user name and set permissions

User Setting:

Click “ ” , swipe right to “ ”, and then the following menu appears. You can modify user password and set permissions. You can’t set the username and password in Node mode, they can be set on the management control unit.

Function Name	Description
Password	Double-click the name in the password list to modify the password of the corresponding user.
Permissions	Set permissions for USB2.0, Audio, KM, Frame Get, and Frame Push.

[Frame Push]

Click [Push] to push the video and USB signals from current receiver to the chosen receiver in the list.

[Frame Get]

Click [Get] to get the video and USB signals from any receiver in the list to the current receiver.

Connection Diagram of Collaborative Sharing Push & Get

[Update]

• Click【RX】to update RX
• Click【TX】to update TX

[Hotkeys]

Function Name	Description
Left _Ctrl	Shows or Hides the UI
Left_ Shift	Disconnect host
Right_ Ctrl	Next or previous channels
Right_Ctrl+Doulbe【1‐0】	Switch from channel 1 to 10

Specifications

Specifications of KFP286K

Specifications		KFP286K _TX	KFP286K_RX
Connections	DisplayPort input	2	N/A
	DisplayPort output	N/A	2
	Power	2x 12V	2x 12V
	LAN port	2x RJ45	2x RJ45
	Optical Module	2x SFP+	2x SFP+
	Mic	3.5mm Stereo Jack (Green)	3.5mm Stereo Jack (Pink)
	Speaker	3.5mm Stereo Jack (Pink)	3.5mm Stereo Jack (Green)
	Square USB	1	N/A
	USB	1	4
Resolution		3840×2160@60Hz
Cable		CAT5e/6/7 or Optical Fiber Cable
I/R Value		DC12V / 3A	DC12V / 3A
Power consumption		15W	16W
Operating temperature		0—50 ℃
Storage temperature		‐20—60 ℃
Humidity		0—80% RH, non‐condensing
Material		Metal
Net weight(kg)		0.94 kg	0.94kg
Product dimension (W × D × H)		212mm x 124.3 mm x 44mm
Package dimension (W × D × H)		243mmx 209mm x 98mm	243mmx 209mm x 98mm

Documents / Resources

Kinan 3030108133G-KFP286K 4K Display Port IP KVM Matrix Extender [pdf] User Manual 3030108133G-KFP286K 4K Display Port IP KVM Matrix Extender, 3030108133G-KFP286K, 4K Display Port IP KVM Matrix Extender, Port IP KVM Matrix Extender, KVM Matrix Extender, Matrix Extender, Extender

References

• User Manual