KICKER HS10 Powered sub Enclosure Owner's Manual

Mounting: Choose a structurally sound location to mount your KICKER-powered subwoofer enclosure. Make sure the mounting screws will not puncture any important parts and allow for ventilation. Mount in the passenger compartment if possible.
HideawayTM Mounting: Attach the brackets to the bottom of the enclosure using the supplied screws. Securely attach the enclosure to the vehicle with the larger screws provided.

Wiring: Observe the polarity of input connections. Use KICKER KISL for RCA outputs or connect directly to speaker-level outputs. Ensure correct wiring for optimal output.
Automatic Turn-On Selection: Choose between +12V and DC Offset turn-on modes on the side panel to control additional amplifiers.

Phase Switch: Invert the phase of the signal played through your subwoofer if needed for better bass response.

FAQs

Q: How do I adjust the bass level?
- A: Use the Remote Bass Level Control included with the enclosure to adjust the bass level to your preference.
Q: What should I do if there is no output from the subwoofer?
- A: Ensure correct wiring connections and polarity. Check if using a LOC that is not wired in reverse. Use the KICKER KISL for optimal performance.

INTRODUCTION

MODEL HS10—————————–

Authorized KICKER Dealer:———————————–
Purchase Date:——————————————-

Model Number:————————————-
Serial Number:—————————————–

The ultra-compact KICKER Hideaway™ Enclosure offers the quickest and easiest way to add a subwoofer to your vehicle, providing signature KICKER bass in a small enclosure.
This system has been meticulously finetuned by KICKER engineers to deliver astounding performance and sound without the time-consuming setup required for a typical amp-sub upgrade.

SPECIFICATIONS

Note: All specifications and performance figures are subject to change. Please visit www.kicker.com for the most current information.

INSTALLATION

Mounting: Choose a structurally sound location to mount your KICKER-powered subwoofer enclosure.
Make sure the mounting screws will not puncture the gas tank/brake lines/wiring or interfere with any mechanical parts on the underside of the mounting surface.
Choose a location that allows at least 4″ (1 0cm) of open ventilation for the amplifier. If possible, mount the enclosure in the climate-controlled passenger compartment.
Mount the brackets to the bottom of the enclosure using the supplied smaller screws. Securely attach the enclosure to the vehicle with the supplied larger screws.

Wiring

Observe the polarity of input connections to avoid signal loss.
Use the KICKER KISL for source units with RCA outputs or splice the quick-connect harness leads directly to your source unit’s speaker-level outputs.
If using an LOC please ensure that it is not wired in reverse. Failure to do so will result in little to no output. KICKER recommends using the KISL as shown above.

quick-connect wiring harness audio inputs:

Automatic Turn-On Selection: KICKER-powered enclosures offer two different automatic tum-on modes that can be selected on the side panel; +12V and DC Offset.
Using the DC Offset mode causes the REM terminal to have +12V out for turning on additional amplifiers.
Remote Turn-On: Set the switch to + 12V to use the remote turn-on lead from your source unit. Run an 18 gauge wire from the Remote Tum-On Lead on your source unit to the terminal labeled REM on the quick-connect wiring harness.
DC Offset Turn-On: If Remote Tum-On is not an option, the next best setting is DC Offset. The DC Offset mode detects a DC offset from the HI-Level speaker outputs when the source unit has been turned on.
Phase Switch: The phase switch lets you invert the phase of the signal played through your powered subwoofer. This is useful if the speakers in your system are out of phase with the subwoofer.
Toggle this switch to find the position that gives you the best bass response.

Input Level: The inputs on KICKER-powered enclosures are capable of receiving either Hi (speaker-level) or Low-level (RCA) signals from your source unit. Set the Input Level switch on the side panel to match the outputs of your source unit.
Crossover Control: The variable crossover on the side panel allows you to adjust the crossover frequency from 50-120Hz. The setting for this control is subjective; 80Hz is a good place to start.
Input Gain Control: The input gain control is not a volume control. It matches the output level of the source unit to the input sensitivity of the amplifier. Maximum power out of the amplifier is possible with the gain in the lowest position. Incorrectly setting the gain can result in distorted output or damage to, and premature failure of, your speakers. For a quick setup, turn the source unit up to about 3/4 volume (if the source unit goes to 30, turn it to 25).

Slowly turn up (clockwise) the gain on the amplifier until you can hear audible distortion, then turn it down a little.
Bass Boost Control: The variable bass boost control on the side panel is designed to give you increased output (0-6dB) at 40 Hz. The setting for this control is subjective. If you turn it up, you must readjust the input gain control to avoid clipping the powered enclosure’s amplifier.
Remote Bass Control: With the included remote bass control, you can control the output level of your powered enclosure remotely. When plugged into the enclosure, the remote bass attenuates the gain level of the signal.

To mount the remote bass level control, simply screw the metal bracket to the chosen location, then slide the housing onto the bracket until it snaps into place.
Run the cable from the controller to the “Remote Bass” jack on your powered enclosure’s side panel. DO NOT disconnect the remote bass control when the amplifier is on!

REMOTE BASS CONTROL INSTALLATION

Connect the supplied 1 /8th inch [3.5mm] patch cable to the CXARC remote and the Remote Bass jack on the amplifier.
Remote cable passes audio; do not run cable parallel to power wires.

TROUBLESHOOTING

If your amplifier does not appear to be working, check the obvious things first such as blown fuses, poor or incorrect wiring connections, incorrect setting of crossover and gain controls, etc. There is a dual-stage PWR/ PRT LED on the side panel of your powered enclosure denoting the power state of the amplifier. When the LED is blue, this indicates the powered enclosure is turned on and its amplifier is functioning properly.

PWR/PRT LED off, no output? With a Volt Ohm Meter (VOM) check the following: 1+ 12 volt power terminal (should read + 12V to 161/) 2 Remote turn-on terminal (should read + 12V to 161/) 3 Check for reversed power and ground connections.
4 Ground terminal, for proper conductivity. 5 Check for blown fuses.
6 Check the AUTO TURN-ON switch setting. Check for a DC offset between a speaker lead and ground if using DC-OFFSET mode.

PWR/PRT LED blue (Amp not in protection}, no or low output? Check the following: 1 audio input connections 2 Check the balance control on the source unit 3 Check the polarity of the input signal connections.
4 Check for a signal in the audio cable feeding the powered enclosure with the VOM meter set to measure “AC” voltage. 5 Substitute source unit with a “known” good source unit.
PWR/PRT LED red (Amp in protection}, no output? 1 Amplifier shuts down only while the vehicle is running = voltage protection circuitry is engaged. Voltage to the amplifier is not within the 10-16 volt operating range. Have the vehicle’s charging and electrical system inspected. 2 A red PWR/PRT LED may also indicate low battery voltage. Check all the connections in your vehicle’s charging system. It may be necessary to replace or charge your vehicle’s battery or replace your vehicle’s alternator.

Reduced bass response? Flip the phase switch to the opposite position; if the bass improves, your speakers are out of phase with the subwoofer.
Ground Noise? KICKER amplifiers are engineered to be fully compatible with all manufacturers’ head units. Some head units may require additional grounding to prevent noise from entering the audio signal.
If you are experiencing this problem with your head unit, in most cases running a ground wire from the RCA outputs on the head unit to the chassis will remedy this issue.

If you still have problems, run your input signal at speaker level from your source unit to the amplifier.
CAUTION: When jump-starting the vehicle, be sure that connections made with jumper cables are correct. Improper connections can result in blown amplifier fuses as well as the failure of other critical systems in the vehicle.
If you have more questions about the installation or operation of your new KICKER product, see the Authorized KICKER Dealer where you made your purchase.

For more installation advice, click on the SUPPORT section on the KICKER homepage, www.kicker.com. Please E-mail support@kicker.com or call Technical Services at 4056248583 for unanswered or specific questions.

LIMITED WARRANTY

ACOUSTICS LIMITED WARRANTY

WARNING: KICKER products are capable of producing sound levels that can permanently damage your hearing! Turning up a system to a level that has audible distortion is more damaging to your ears than listening to an undistorted system at the same volume level. The threshold of pain is always an indicator that the sound level is too loud and may permanently damage your hearing. Please use common sense when controlling volume.

When purchased from an Authorized KICKER Dealer, KICKER warrants this product to be free from defects in material and workmanship under normal use for a period of ONE (1) YEAR from the date of original purchase. If this product is identified as “Refurbished” or “B Goods”, the warranty is limited to a period of THREE (3) MONTHS from the date of the original purchase. In all cases, you must have the original receipt. Should service be necessary under this warranty for any reason due to manufacturing defect or malfunction during the warranty period, KICKER will repair or replace (at its discretion) the defective merchandise with equivalent merchandise. Warranty replacements may have cosmetic scratches and blemishes.
Discontinued products may be replaced with more current equivalent products. This warranty is valid only for the original purchaser and is not extended to owners of the product after the original purchaser.
Any applicable implied warranties are limited in duration to a period of the express warranty as provided herein beginning with the date of the original purchase at retail, and no warranties, whether express or implied, shall apply to this product thereafter.

Some states do not allow limitations on implied warranties; therefore, these exclusions may not apply to you. This warranty gives you specific legal rights; however, you may have other rights that vary from state to state.

WHAT TO DO IF YOU NEED WARRANTY OR SERVICE:

Defective merchandise should be returned to your local Authorized Stillwater Designs (KICKER) Dealer for warranty service.

Assistance in locating an Authorized Dealer can be found at www.kicker.corn or by contacting Stillwater Designs directly. You can confirm that a dealer is authorized by asking to see a currently authorized dealer window decal.
If it becomes necessary for you to return defective merchandise directly to Stillwater Designs (KICKER), call the KICKER Customer Service Department at 4056248510 for a Return Merchandise Authorization (RMA) number.
Package only the defective items in a package that will prevent shipping damage, and return them to: Stillwater Designs, 3100 North Husband St, Stillwater, OK 74075.

The RMA number must be marked on the outside of the package. Please return only defective component systems. The return of functioning items increases your return freight charges. Non-defective items will be returned freight collected to you.
For example, if a subwoofer is defective, only return the defective subwoofer, not the entire enclosure. Include a copy of the original receipt with the purchase date visible, and a “proof-of-purchase” statement listing the Customer’s name, Dealer’s name and invoice number, and product purchased. Warranty expiration on items without proof of purchase will be determined by the type of sale and manufacturing date code. Freight must be prepaid; items sent freight-collect, or COD, will be refused.

WHAT IS NOT COVERED?

This warranty is valid only if the product is used for the purpose for which it was designed.

It does not cover:

Damage due to improper installation

Subsequent damage to other components
Damage caused by exposure to moisture, excessive heat, chemical cleaners, and/or UV radiation
Damage through negligence, misuse, accident, or abuse.

Repeated returns for the same damage may be considered abuse
Any cost or expense related to the removal or reinstallation of the product
Speakers damaged due to amplifier clipping or distortion

Items previously repaired or modified by any unauthorized repair facility
Return shipping on non-defective items
Products with tampered or missing barcode labels

Products with tampered or missing serial numbers
Products returned without a Return Merchandise Authorization (RMA) number
Products purchased from an UNAUTHORIZED dealer

Freight Damage
The cost of shipping pthe roduct to KICKER
Service performed by anyone other than KICKER

HOW LONG WILL IT TAKE?

KICKER strives to maintain a goal of one-week service for all acoustics (subwoofers, midrange drivers, tweeters, crossovers, etc) returns. Delays may be incurred if an ack of replacement inventory or parts is encountered.
Failure to follow these steps may void your warranty. Any questions can be directed to the KICKER Customer Service Department at 4056248510.

Contact your International KICKER dealer or distributor concerning specific procedures for your country’s warranty policies.
P.O. Box 459 Stillwater, Oklahoma 74076 USA 4056248510

INTERNATIONAL WARRANTY

Contact your International KICKER dealer or distributor concerning specific procedures for your country’s warranty policies.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage.
You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

Documents / Resources

KICKER HS10 Powered sub Enclosure [pdf] Owner's Manual
HS10, 51HS10, HS10 Powered sub Enclosure, HS10, Powered sub Enclosure, sub Enclosure

References

User Manual

KICKER HS10 Powered sub Enclosure

Product Information