Kibosh-loog

Kibosh MT6000 Wireless Router

Kibosh-MT6000 -Wireless-Router-product

SETTING UP

Power On

When your Kibosh is powered up, you’ll see two new WiFi networks: Kibosh and Kibosh_5G

Connect via Wi-Fi

Connect to the Wi-Fi called Kibosh using the password abcd0001Kibosh-MT6000 -Wireless-Router-fig (2),,,.

Set Up Router

  • A. Use included Ethernet cable:plug one end into left Kibosh WAN port… the other end into an upstream ISP router/modem LAN port.
  • B. Power cycle the upstream router/modem & wait 3 min.
  • C. Go to https://Kibosh.com/Setup
  • D. Scan QR code to activate your Kibosh

Kibosh-MT6000 -Wireless-Router-fig 5

SUPPORT

Kibosh-MT6000 -Wireless-Router-fig (3)

Troubleshooting

If you cannot access https://Kibosh.com/Setup..

  • Ensure you’re connected to WiFi:Kibosh, passkey abcd0001
  • Ensure included Ethernet cable is securely attached:Kibosh WAN to upstream modem/router LAN ports.
  • Power cycle both the Kibosh and upstream router/modem.
  • Check to make sure your Internet Service Provider is working.Kibosh-MT6000 -Wireless-Router-fig (4)

Technical Support

WARRANTY

  • We provide one year limited warranty for routers and 3-month limited warranty for accessories. Extra warranty may apply according to the local law in which the product purchase took place.
  • Highly recommend using the included 12V/4A power adapter.
    Any damage to the router caused by not following the instructions will render this warranty null and void. Any damage to the router caused by modifying the PCBA, components or case will render this warranty null and void. Issues caused by the use of third-party firmware may not get official support from us.
  • Any damage to the router caused by inappropriate use, e.g. inappropriate voltage input, high temperature, dropping in the water or on the ground will render this warranty null and void.
  • Pictures on the instructions are only for reference. We reserve the right to change or modify these materials without further notice.

FCC Statement

FCC ID: 2BKM3-MT6000

  1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
    1. This device may not cause harmful interference, and
    2. This device must accept any interference received, including interference that may cause undesired operation.
  2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
  3. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help important announcement.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and vour body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

The user manual for LE-LAN devices shall contain instructions related to the restrictions mentioned in the above sections, namely that:

i. the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
The functions of Wireless Access Systems including Radio Local Area Networks(WAS/RLANs) within the band 5150-5350 MHz for this device are restricted to indoor use only within all European Union countries.

Hereby, Kibosh declares that the radio equipment type [AX6000 Wireless Router, GL-MT6000] is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://Kibosh.com Frequency bands: 2.4G WIFI:2.412-2.472GHz; 5G WIFI:5.15-5.25GHz 5.25-5.35GHz 5.47-5.725GHz 5.725-5.85GHz Kibosh LLC
9 East Lookerman Street, STE 202 Dover DE 19901 USA

Kibosh-MT6000 -Wireless-Router-fig 6

Documents / Resources

Kibosh MT6000 Wireless Router [pdf] User Manual
2BKM3-MT6000, 2BKM3MT6000, mt6000, MT6000 Wireless Router, MT6000, Wireless Router, Router

References

Leave a comment

Your email address will not be published. Required fields are marked *