KSB101,KSB102 Key Security Box
“
Product Information
Specifications
- Models: KSB 101 and KSB 102
- Dimensions: 215 x 215 x 395 mm
- Colour: RAL 9006
Product Usage Instructions
1. Determine Installation Location
Before starting, use Drawing 1 to determine the place where you
want the safe to be installed. Ensure there is at least 30 cm of
space between the safe and any corners, the end of the wall, floor,
and ceiling.
2. Installation Method A or B
Choose between installation method A or B as described above.
See Drawing 2 for more details.
3. Installation Steps
- Draw the drill holes on the wall as per the instructions.
- Install the safe using the chosen installation method A or
B. - Place the rings and bolts inside the safe on the wire end [4x] and tighten firmly.
4. Optional Rain Cap Installation
To keep rain out, place the rain cap on top of the safe. Ensure
the top of the box is grease-free and use mounting glue such as
Zwaluw High Tack to secure the cap firmly in place.
5. Maintenance
Regularly check whether the drainage holes on the bottom of your
KeySecurityBox are open and ensure all bolts are still solid and in
place. Treat for possible rust as needed.
FAQ
Questions?
For any questions, contact your supplier, visit our website at
www.keysecurityproducts.com, or send an email to
info@keysecurityproducts.com.
“`
+31 35 – 53 306 58
KSB101/KSB102
User manual English
info@keysecurityproducts.com
www.keysecurityproducts.com
Note: before you start, use drawing 1 to determine the place where you want the safe to be installed. Also choose the installation method A or B as described above. See also drawing 2 for more details.
NB If need be ask your local hardware store about the installation material and when drilling always make sure you avoid pipes or wires.
Specifications
Models: KSB 101 and KSB 102 Dimensions: 215 x 215 x 395 mm Colour: RAL 9006
Box content
· 1 x KeySecurityBox · 1 x floor mat for in the safe · 4 x Ring ø 30 mm, hole ø 10.5 mm · 2 x safe key
Congratulations on choosing our ultrareliable KeySecurity, the ideal solution for keys and keycards. The KeySecurityBox is extremely durable and, thanks to the range of models, there’s always a solution to meet your need..
You have chosen either the KSB 101 (with the deposit wheel on the left) or the 102 (with the deposit wheel on the right). Both are intended for installation against a wall. As described below, there are two ways to do this.
You will need the following for installation (not included)
· Flexible steel rule · Pen/pencil · Level · Hammer drill with drill · Spanner and/or socket wrench · Anchor bolts or key bolts (installation A) · Screw studs plus bolts (installation B)
A – With anchor bolts or key bolts. These are suitable for installation in solid materials such as concrete, hard stone and hard natural stone (maximum M10).
B – With screw studs through the wall. If the wall consists of a porous type of stone or any other non-solid construction material, drill holes through the wall and then install the safe using screw studs on which you install the wall installation plate on the inside using rings and bolts.
+31 35 – 53 306 58
info@keysecurityproducts.com
www.keysecurityproducts.com
1 Determine where you want to install the safe. Make sure there is at least 30 cm between the safe and any corners, the end of the wall, floor and ceiling. 215 mm
395 mm
min 300 mm
2 Draw the drill holes on the wall. Drill four holes in the wall. Consult the description of your installation materials with respect to the diameter and depth of the holes.
50 mm
70 100 mm mm
100 70 mm mm
175 mm
Model 101
Model 102
Ø 10 mm
Ø 10 mm
15 mm
15 mm
+31 35 – 53 306 58
Montage A
Montage B
info@keysecurityproducts.com
www.keysecurityproducts.com
3 Install the safe using the chosen installation method A or B
Model 101
Model 102
4 Place the rings and bolts inside the safe on the wire end [4x] and tighten firmly. Your safe is ready for use.
Model 101
Model 102
4x
4x
+31 35 – 53 306 58
info@keysecurityproducts.com
www.keysecurityproducts.com
Optional
Place the rain cap to keep the rain out. Make the top of the box grease-free and apply a mounting glue such as Zwaluw High Tack and place the cap and press it so that it fits firmly.
Maintenance
Regularly check whether the drainage holes on the bottom of your KeySecurityBox are open and whether all the bolts are still solid and in place. Treat for possible rust.
Questions?
Ask your supplier, check on: www.keysecurityproducts.com
or send an email to: info@keysecurityproducts.com
Please make sure the key drops into the safe
Disclaimer with respect to installation, breakage and the
The manufacturer and vendor of the KeySecurityBox are not liable for the installation. The installation is easy although we recommend you ask a contractor or other professional to do it for you. The KeySecurityBox is intended for depositing keys and keycards and not for paper and other objects that may get stuck in the deposit wheel. The KeySecurityBox is an anti-the and anti-breakage box, although with excessive violence the and breakage are possible. The use is therefore for personal risk and the manufacturer and vendor of the KeySecurityBox are not liable for breakage or the or physical harm caused by its incorrect use.
© 2021 Dutch Trading Company
+31 35 – 53 306 58
info@keysecurityproducts.com
www.keysecurityproducts.com
Documents / Resources
 |
KEYSECURITYBOX KSB101,KSB102 Key Security Box [pdf] User Manual KSB 101, KSB 102, KSB101 KSB102 Key Security Box, KSB101 KSB102, Key Security Box, Security Box, Box |