Keychron K8 Max Wireless Mechanical Keyboard

Keychron
KS Max Wireless Mechanical Keyboard

Fully Assembled Version

Keyboard
1x Fully Assembled Keyboard

Including

• 1x Case
• 1x PCB
• 1x Steel Plate
• 1x Sound Absorbing Foam
• 1x IXPE Foam
• 1x PET Film
• 1x EPDM Foam
• 1x Bottom Case PET Film
• 1x Silicone Bottom Pad
• 5 Sets x Stabilizers
• 1 Set x Keycaps (PBT Double-shot)
• 1 Set x Switches

Cable
1x Type-A to Type-C Cable

Receiver
1x Type-A 2.4GHz Receiver
1x Extension Adapter For Receiver

Tools
1x Keycap & Switch Puller
1x Screwdriver
1x Hex Key (Aluminum-Frame Version only)*

Barebone Version

Keyboard Kit

1x Keyboard Kit (Without Keycaps & Switches)

Including

• 1x Case
• 1x PCB
• 1x Steel Plate
• 1x Sound Absorbing Foam
• 1x IXPE Foam
• 1x PET Film
• 1x EPDM Foam
• 1x Bottom Case PET Film
• 1x Silicone Bottom Pad
• 5 Sets x Stabilizers

Cable
1x Type-A to Type-C Cable

Receiver
1x Type-A 2.4GHz Receiver
1x Extension Adapter For Receiver

Tools
1x Keycap & Switch Puller
1x Screwdriver
1x Hex Key (Aluminum-Frame Version only)*

QUICK START GUIDE
If you are a Windows user, please find the appropriate keycaps in the box,then follow the instructions below to find and replace the following keycaps.

1. Connect 2.4GHz Receiver Connect 2.4GHz Receiver
   Switch toggle to 2.4GHz mode Note: For the best wireless experience, we recommend using the extension adapter for receiver and putting the 2.4GHz receiver somewhere on your desk close to your keyboard for a low rate of latency and fewer signal interferences.
2. Connect Bluetooth
3. Connect Cable
4. Switch To The Right System
   Please make sure the system toggle on the top left corner has been switched to the same system as your computer’s operating system.
5. The Backlight
6. Adjust The Backlight Brightness
7. The Keychron Launcher App
   Please visit launcher.keychron.com to access the Keychron online launcher app. This app enables users to remap keys, adjust key actuation points, assign multiple commands to a single key, enter game controller mode, and more.
   If it cannot recognize your keyboard, please reach
   our support to get instruction.
   ‘The online launcher App can only run on the latest version of Chrome, Edge, and Opera browsers yet.
   ‘The online launcher App only works when the keyboard is connected by wire to the computer.
8. The Layers
   There are four layers of key settings on the keyboard. The layer O and layer 1 are for the Mac system. The layer 2 and layer 3 are for the Windows system.
   If your system toggle is switched to Mac, then the layer O will be activated.
   If your system toggle is switched to Windows, then the layer 2 will be activated. Remember that if you are using it in Windows mode, please make changes to the layer 2 instead of the top layer (the layer 0). This is a common mistake people are making.
   
9. Factory Reset & Firmware Update
   Troubleshooting? Don’t know what’s going on with the keyboard? Factory reset your keyboard
   1. Power on your keyboard.
   2. Press and hold In + J + Z (for 4 seconds). The keyboard backlight will flash in red quickly for 3 seconds, indicating that the keyboard has been reset.
10. Flash your keyboard firmware 
    1. Visit launcher.keychron.com to open the online Launcher web app.
    2. Ensure the keyboard is in Cable or Wired mode and plug in the power cable.
    3.  Find the ‘Firmware Update’ tab on the left side of the Launcher and connect your keyboard with it.
    4. Follow the instructions on the Launcher and complete the firmware update.
       *Step-by-step guide, search the keyword “firmware” on keychron.com.

 Warranty

The keyboard is highly customizable and easy to be rebuilt. If anything goes wrong with any of the keyboard components of keyboard during the warranty period, we will only replace the defective parts of the keyboard, not the whole keyboard.

KB MAX WIRELESS MECHANICAL KEYBOARD SPECIFICATIONS

• Number of keys: 87
• Switch type: Mechanical
• Battery: 4000mAh
• Charging time: Around 5 hours
• Charging port: Type-C
• Mode: Bluetooth / Wired / 2.4GHz
• Bluetooth operating distance: Within 10 meters (open space)
• Name of Bluetooth device: Keychron K8 Max

LED STATUS OVERVIEW

LED Location	Function	Status
		Low Power – Red Light Blinking
Power Indicator	Charging	Charging – Static Red
		Full charged – Static Green
		Reconnecting – Fast Blinking
Bluetooth / 2.4 GHz Indicator	Bluetooth / 2.4 GHz	Paired – Light off Pairing – Slow Blinking
Caps Lock Indicator	Caps Lock	Enable Caps Lock – Static Blue Disable Caps Lock – Light Off

KB MAX WIRELESS MECHANICAL KEYBOARD OVERVIEW

1. Power Indicator
2. Bluetooth / 2.4G Indicator
3. Caps Lock Indicator
4. T ype-C Port
5. Win/Android Mac/iOS(OS Toggle)
6. 2.4G I Cable / BT (Connection Mode Toggle)

 

DEFAULT KEY LAYOUT:
LAYER 0: This layer will be activated when your keyboard’s system toggle is switched to Mac.

• LAYER 1: This layer will be activated when your keyboard’s system toggle is switched to Mac and press the fn/M0(1) key.
• LAYER 2: This layer will be activated when your keyboard’s system toggle is switched to Windows.
• LAYER 3: This layer will be activated when your keyboard’s system toggle is switched to Windows and press the fn/M0(3) key.

KEY DESCRIPTION

Key Description
Ser-	Screen Brightness Decrease
Ser+	Screen Brightness Increase
Bright-	Backlight Decrease
Bright+	Backllght Increase
Prvs	Previous
Play	Play/Pause
Next	Next
Mute	Mute
Vol-	Volume Decrease
Vol+	Volume Increase
RGB Toggle	Turn Backlight on/off
RGBMd+	RGB Mode Next

RGBMd-	RGB Mode Previous
Hue+	Hue Increase
Hue-	Hue Decrease
RGB SPI	RGB Speed Increase
RGBSPD	RGB Speed Decrease
M0(1)	Layer 1 will be activated when holding this key
M0(3)	Layer 3 will be activated when holding this key
BTH1	Bluetooth Host 1
BTH2	Bluetooth Host 2
TH3	Bluetooth Host 3
2.4G	2.4GHz Host
Batt	Battery life

Key Description
NKRO	N-key rollover
Task	Task View
File	File Explorer
MCtl	Mission Control
LPad	Launch Pad

FUNCTION DESCRIPTION:

CHARGING

Plug the cable into a USB port and plug the other end into the keyboard port. Power Indicator:
A red light will stay on while charging; Fully charged in around 5 hours, a green power indicator will appear.
*The KB Max keyboard is compatible with all USB ports. Please use a SV 1A adapter or USB 3.0 for the best performance. The KB Max can be charged in 2.4GHz/Cable/Bluetooth mode.
**This product supports up to SV charging voltage and 1A charging current. We are not responsible for any problems caused by improper charging.
2.4GHz I CABLE/ BLUETOOTH MODE (MODE TOGGLE)
2.4GHZMODE

1. Connect the 2.4GHz receiver to your device’s USB Port.
2. Switch the toggle to the 2.4GHz option. The keyboard will automatically connect to your device.

BWETOOTH MODE

1. Switch the toggle to the Bluetooth option.
2. Backlighting will be turned on.
3. Hold “fn+l” key for 4 seconds to activate Bluetooth pairing (the Bluetooth indicator fast flashes for 3 minutes to detect pairing).
4. Search for the Bluetooth device “Keychron KS Max” on your device and connect it (the Bluetooth indicator goes off after successful pairing).

Note: This keyboard supports pairing up to 3 devices simultaneously via key combination “fn” + “1” I “fn” + “2” I “fn” + “3”.
*The Bluetooth indicator will continue to flash for 3 minutes.
**Slow or failed connections may exist due to different Bluetooth versions, please make sure all the settings are correct.

SWITCH BLUETOOTH DEVICES
Short press key combination “fn” + “1” I “fn” + “2” I “fn” + “3” to switch to other device.

RECONNECT:

1. Switch the keyboard to the Bluetooth option to activate the keyboard.
2. The Bluetooth indicator flashes for 3 seconds and automatically pairs with the last paired device.
3. If the Bluetooth indicator is off, press any button to enter the connection again.

* The keyboard must have been paired with the device to perform this function.

WIRED MODE

1. Switch the toggle to the Cable option .
2. Connect our cable with your PC and keyboard.
3. Backlighting will be turned on.

*Under Wired Mode, keyboard will not enter into Battery Saver Mode.

TURN OFF THE KEYBOARD
Switch the keyboard to the Cable option and unplug the power cable.

BACKLIGHT SETTING

• Short press key combination “fn” + “tab” to turn the backlight on/off.
• Short press key combination “fn” + “Q” or “fn” + “A” to switch between different types of lighting effects.

OS TOGGLE SWITCH

1. MAC/iOS
   Switch the toggle to Mac/iOS when the keyboard is connected to a Mac or iOS operating system.
2. WINDOWS/ANDROID
   Switch the toggle to Windows/Android when the keyboard is connected to a Windows or Android operating system.
   *When using the Windows/ Android mode, 00 keys are used for “Windows” and “Alt” functions.
3. INPUT METHOD SWITCH
   • For iOS:
     Input method switch: Ctrl + Space
     Caps Lock: Caps (Enable General>Keyboards>Hardware Keyboard>Caps Lock Language Switch)
   • For Android:
     Input method switch: Shift+ Space
     NOTE: Functions of certain multimedia key may be disabled due to compatibility, versions, brands and drivers of Windows/ Android OS. We also recommend not to switch OS frequently as it may impact keyboard operations.

TROUBLESHOOTING

• If unable to pair keyboard to device, confirm that the device you’re trying to pair with is Bluetooth-capable. If so, restart the device and try pairing it with the keyboard again.
• Note: On a Windows computer, a new Bluetooth connection will sometimes require additional software updates-a process that may still be ongoing after a message appears indicating a successful completion. Wait at least 20 minutes after pairing to make sure all updates are completed before restarting the computer.
• Confirm that the device is configured to accept Bluetooth connections (Windows) and supports an external keyboard (HID profile).
• Go to Bluetooth Devices > Open Settings and select the following:
• Allow Bluetooth devices to find this computer
• Allow Bluetooth devices to connect to this computer
• Alert me when a Bluetooth device wants to connect

My keyboard isn’t working in Bluetooth mode.

• For the computer/smartphone:
• Go to your device Bluetooth settings>Select the keyboard and remove/delete/unpair it.
• Then restart your device.
• For the keyboard:
• Turn the keyboard off and back on. Then reconnect it to your device.

My keyboard isn’t working in 2.4 GHz mode.
Ensure the toggle is set to 2.4 GHz, remove the receiver from your device, and press “fn” + “4” for 4 seconds to force pair, then reinsert the receiver into the device, keeping the keyboard within 20 cm of the receiver for optimal pairing.
Wireless connection is interrupted even within 10 meters.
Check if the keyboard is resting on a metal surface that can iinterfere with the wireless signal.
Third-party input tools are not compatible with the keyboard.
Due to compatibility, versions, brands and drivers of Windows/Android OS, functions of third-party input tools may be affected while using the keyboard. Please make sure your operating system and drivers are up to date.

Certain multimedia keys or function keys do not work.
Functions of certain multimedia keys may be disabled due to compatibility, versions, brands, and drivers of devices.

Safety Precaution:
Keep the product, accessories and packaging parts out of the reach of children to prevent any accidents and choking hazards.
Always keep the product dry to avoid corrosion.
Do not expose the product to extreme temperatures below -10°C(14° F) or above 50°C(122° F) to preserve the lifespan of the keyboard.
Keychron, Inc.

• Dover, DE 19901, United States
• Find us at:
• https://www.keychron.com
• Support@keychron.com
• @keychron
• @keychron
• X@keychronMK
• Designed by Keychron
• Made in China

Documents / Resources

	Keychron K8 Max Wireless Mechanical Keyboard [pdf] User Guide K8 Max, K8 Max Wireless Mechanical Keyboard, K8 Max Mechanical Keyboard, Wireless Mechanical Keyboard, Mechanical Keyboard, Wireless Keyboard, Keyboard
	keychron K8 Max Wireless Mechanical Keyboard [pdf] User Guide K8 Max, K17 Max, K8 Max Wireless Mechanical Keyboard, K8 Max, Wireless Mechanical Keyboard, Mechanical Keyboard, Keyboard

References

• User Manual