
KASK Quantum Neck Protector Fr User Manual






NECK PROTECTOR FR / QUANTUM NECK PROTECTOR

WARNING:
Please read the following operating instructions carefully. This Information Note should be retained for the life of the PPE. This Information Note has been approved by the notified body CENTRO TESSILE COTONIERO E ABBIGLIAMENTO SPA, Piazza S. Anna, 2 21052 BUSTO ARSIZIO (VA) Country: Italy n° 0624 which issued the EU certification as required by EU Regulation 2016/425 for Personal Protective Equipment (PPE). The PPE is UKCA marked according to EU Regulation 2016/425 on personal protective equipment as amended to apply in GB. The EU Declaration of Conformity and the UKCA Declaration of Conformity are available at the following Internet address: www.kask.com.
REGULATORY REFERENCES: The PPE has been manufactured in such a way as to comply with the requirements prescribed by the following technical standards:
- Regulation (EU) 2016/425 of the European Parliament and Of the Council of 9 March 2016.
- EN13688:2022- “Protective clothing – General requirements”.
- EN 11612:2015 – “ Protective clothing. Clothing to protect against heat and flame”.
- EN 13034:2005+A1:2009 – “ Protective clothing against liquid chemicals – Performance requirements for chemical protective clothing offering limited protective performance against liquid chemicals (Type 6 and Type PB [6] equipment)”.
- EN 1149-5:2018 – “ Protective clothing – Electrostatic properties
The
marking indicates compliance with the essential health and safety requirements of REGULATION (EU) 2016/425 on personal protective equipment.
USE:
This PPE protects the neck and, partially, the head from accidental contact with small flames, not high values of convective, radiant and contact heat, chemicals within the limits of the marked levels. The choice of suitable PPE should be made on the basis of the specific requirements of the workplace, the type of risk, the level of experience/training and the environmental conditions. The suitability of the characteristics of this model of garment for your needs should be verified prior to use. Do not use for hazards other than those mentioned above. As required, wear in combination with other appropriate protective clothing to ensure complete protection of the body, even during movements.
The manufacturer declines all responsibility for damage caused by improper use of the PPE.
According to our knowledge, the garment does not contain allergenic substances; please report any cases of allergic reactions. The pH and azo dyes content are within the requirements of these standards.
COMPATIBILITY:
see table A.
LIMITS OF USE:
This PPE is not suitable for use in operations where resistance to permeation of chemicals at the molecular level is essential,
or a complete barrier to liquid or gaseous chemicals is required (e.g., situations where there is a risk of exposure to massive and powerful
emissions of concentrated liquid chemicals) and for all uses not mentioned in this information note,
WARNINGS:
Modifications to the PPE are not permitted.
WARNING: In the event of accidental splashing of chemical or flammable liquids onto the PPE while it is worn, the wearer must immediately remove the garment ensuring that the chemical or liquid does not come into contact with any part of the skin. The PPE should then be laundered or removed from service. WARNING: The garment only offers protection for the part of the body actually covered, and must therefore be supplemented, depending on the intended use, with PPE suitable for protecting those parts of the body not covered by the PPE. WARNING: the PPE can only provide the performance levels indicated in this information note if it is correctly assembled, worn and closed. The manufacturer declines all responsibility due to incorrect fitting and/or assembly of the garment.
WARNING: The person wearing protective clothing that dissipates electrostatic charges must be properly grounded. The resistance between the person’s skin and ground must be less than 108 Ω, for example by wearing suitable footwear on dissipative or conductive flooring.
WARNING:
Protective clothing that dissipates electrostatic charges must not be opened or removed in the presence of flammable or explosive atmospheres, or when handling flammable or explosive substances. WARNING: Electrostatic dissipative protective clothing is intended to be worn in Zones 1, 2, 20, 21 and 22 (see EN 60079-10-1 and EN 60079-10-2) where the minimum ignition energy of any explosive atmosphere is not less than 0016mJ. WARNING: Protective clothing that dissipates electrostatic charges should not be used in oxygen-enriched atmospheres, or in Zone 0 (see EN60079-10-1), unless approved in advance by the Safety Officer. CAUTION: The ability of protective clothing to dissipate electrostatic charges may be affected by wear, tearing, washing and contamination. WARNING: Electrostatic dissipative protective clothing must be worn in such a way that it permanently covers all non-conforming materials during normal use (including bending and movement).
USE:
Checks before use: it is compulsory to check the garment to ensure that there are no alterations such as: tears, charring, unstitching, illegible markings. Should any of the above conditions occur, the PPE should be replaced.
ASSEMBLY AND DISASSEMBLY:
Assembly on ZENITH, ZENITH X, PRIMERO helmets and variants: insert the clips of the PPE’s upper stick inside the 3 holes in the back of the helmet (fig.1). Secure the Velcro straps to the helmet’s harness by looping them through the side slots of the headband (fig.2) then fold them towards the inside of the helmet to close them in on themselves. Put the head on then close the Velcro straps at the front so that they overlap completely (fig. 8). Disassembly: remove the 3 clips (fig.3-4), and repeat the previous steps, reversing the sequence. Assembly on QUANTUM helmets and variants: Fasten the Velcro straps inside the helmet in the positions indicated (fig.5).
Insert the clips of the upper PPE splint inside the 3 holes in the back of the helmet (fig.6). Hook the Velcro straps of the nape protector to the corresponding ones on the inside of the helmet (fig. 7/7a). Put the head on, then close the Velcro straps at the front so that they are completely overlapping (fig. 8). Disassembly: Repeat the previous operations, reversing the sequence.
MAINTENANCE AND STORAGE:
Store the PPE in its original packaging in a cool, dry place, away from oils and/or grease. In these conditions, the PPE retains its suitability for use for a long time so it has proved impractical to establish an “expiry date”: KASK S.p.A. recommends that the PPE should be replaced no later than 5 years after purchase or if a technical standard has been superseded by an updated version.

DISPOSAL:
If the PPE has not been contaminated with particular substances or products, it may be disposed of as normal textile waste, otherwise follow the legal requirements for special waste.
SIGNIFICANCE OF THE MARKING:
the following label is shown inside the PPE: (fig.9). (1) Manufacturer identification, (2) Model, (3) Category, (4) Fabric composition, (5) CE marking, (6) UKCA marking, (7) Heat and/or fire protection pictogram and levels of performance, (8) Chemical protection pictogram, (9) Electrostatic properties pictogram, (10) “Read manufacturer’s instructions and information” symbol, (11) Size, (12)
Maintenance symbols. An additional label shows the month and production of the PPE (mm/yyyy).
PERFORMANCES

EN 13034:2009
The PPE offers resistance to chemical aggression by products which are not immediately dangerous to health and safety, providing adequate protection against accidental contact (non-abundant sprays, aerosols, etc.) and enabling the operator to clean or replace the garment in good time.

Electrostatic Properties (base fabric only) – EN 1149-5:2018

ACCESSORIES AND SPARE PARTS: not provided.
3-YEAR WARRANTY: KASK guarantees the product for three years from the date of purchase for any defect in materials or workmanship. The warranty does not cover defects due to normal wear and tear of the product, modifications, poor storage or use other than that for which the device has been certified.
Authorized representative for UK: AUTHORISED REP COMPLIANCE LTD, Arc House, Thurnham, Lancaster, LA2 0DT, UK.
Read More About This Manual & Download PDF:
Documents / Resources
![]() | Quantum Neck Protector Fr |
References
- Kask Shop Online - Sport Helmets & Accessorieswww.kask.com
- User Manualmanual.tools
