KARCHER K4 Power Control Flex Instruction Manual

This high-pressure cleaner is designed for efficient cleaning
tasks, providing powerful water jets to remove dirt and grime from
various surfaces. It comes with safety features to ensure proper
usage and prevent accidents.

Product Usage Instructions

Safety Instructions

Read and follow all safety instructions provided in the manual
before using the device. Keep the original instructions for future
reference. Make sure to consider general safety regulations and
accident prevention guidelines.

Hazard Levels

DANGER: Indicates imminent threat of danger
leading to severe injuries or death.
WARNING: Indicates potentially dangerous
situations that may lead to severe injuries or death.

CAUTION: Indicates potentially dangerous
situations that may lead to minor injuries.
ATTENTION: Indicates potentially dangerous
situations that may lead to property damage.

Operation

DANGER: Do not use in explosive atmospheres.
Avoid suctioning solvents or undiluted acids. Maintain a safe spray
distance when cleaning wheels/tyre valves.

WARNING: Use proper protective clothing. Do not
aim high-pressure jet at yourself or others. Check device and
accessories before each operation.

CAUTION: Ensure proper use with a system
separator. Wear protective clothing and safety goggles to prevent
water or dirt backsplash. Use suitable respiratory protective masks
depending on the environment.

Frequently Asked Questions (FAQ)

Q: Can I use this high-pressure cleaner on all surfaces?

A: It is recommended to check the manufacturer’s guidelines for
suitable surfaces to avoid damage.

Q: How often should I inspect the device for damages?

A: It is advised to inspect the device and accessories before
each operation and replace damaged components immediately.

“`

View Fullscreen

K 4 Power Control K 4 Premium Power Control

English

59795560 (10/24)

A
2

B
3

Contents
KÄRCHER Home & Garden app ……………………. 6 Safety instructions ……………………………………….. 6 Environmental protection………………………………. 8 Intended use……………………………………………….. 8 Accessories and spare parts …………………………. 8 Scope of delivery …………………………………………. 8 Device description ……………………………………….. 8 Safety devices …………………………………………….. 9 Symbols on the device …………………………………. 9 Installation ………………………………………………….. 9 Initial startup ……………………………………………….. 9 Operation……………………………………………………. 10 Transport ……………………………………………………. 11 Storage………………………………………………………. 11 Care and service …………………………………………. 11 Troubleshooting guide ………………………………….. 12 Warranty …………………………………………………….. 12 Technical data …………………………………………….. 12 Declaration of Conformity ……………………………… 13
KÄRCHER Home & Garden app
The KÄRCHER Home & Garden app contains: Installation and initial startup information Information about the areas of application Tips & Tricks FAQ with detailed troubleshooting Connection to the KÄRCHER Service Centre The app can be downloaded here:
Trademarks Google PlayTM and AndroidTM are trademarks or
registered trademarks of Google Inc. Apple® and App store® are trademarks or registered
trademarks of Apple Inc.

Safety instructions
Read this safety chapter and these origi-
nal instructions before using the device for the first time. Act in accordance with them. Keep the original instructions for future reference
or for future owners. In addition to the notes in the operating instructions,
you also need to take into consideration the general
safety regulations and accident prevention guidelines applicable by law. Warnings and information notices attached to the device provide important information for hazard-free operation.
Hazard levels
DANGER
Indication of an imminent threat of danger that will lead to severe injuries or even death.
WARNING
Indication of a potentially dangerous situation that may lead to severe injuries or even death.
CAUTION
Indication of a potentially dangerous situation that may lead to minor injuries.
ATTENTION
Indication of a potentially dangerous situation that may lead to damage to property.
Operation
DANGER Operation in explosive atmos-
pheres is prohibited. Never suction solvents, liquids containing solvents or undiluted acids. This includes e.g. petrol, paint thinner or heating oil. The spray mist is highly flammable, explosive and poisonous. Damaged wheels / tyre valves are extremely dangerous. Damaged wheels / tyre valves can be damaged by the
high-pressure jet and explode. The first sign of this is discolouration of the tyres. Keep a spray distance of at
least 30 cm when cleaning the wheels / tyre valves.
WARNING Do not use the device if people
without the proper protective clothing are in its reach. Do not aim the high-pressure jet at yourself, e.g. to clean clothes or shoes. Do not direct the high-pressure jet at persons, animals, live electrical equipment or at the device itself. Do not spray any objects which contain harmful substances (e.g. asbestos). Check the device and the accessories, such as the high-pres-
sure hose, high-pressure gun and safety devices, to make sure they are in proper safe and reliable condition before each operation. Do not use the device if it is dam-
aged. Replace damaged components immediately. Only use high-pressure hoses, control panels and couplings specified by the manufacturer. Risk of scalding. When disconnecting the supply or high-pressure hose, hot water can leak out of the connections af-
ter operation.

English

CAUTION According to the applicable regu-
lations, the appliance may never be used with the drinking water network without a system separator. Ensure
that the connection to your house water system, with which the high-pressure cleaner is operated, is equipped with a system separator according to EN 12729 type BA. Water that has flowed through a system separator is no longer classified as drinkable. Never leave the device unsupervised while it is in operation. Recoil force from the water stream emerging at the high-pressure nozzle acts on the high-pressure gun. Keep proper footing and hold the high-pressure gun and spray lance firmly. Accidents or damage due to the device falling over. Before all actions with or on the device, you must make sure that it is stable.
ATTENTION Do not operate the device at tem-
peratures below 0 °C.
Protective gear
CAUTION Wear suitable protective clothing
and safety goggles to protect yourself from water or dirt backsplash. Aerosols can be formed when using highpressure cleaners. Inhaling aerosols can be harmful for
your health. Depending on the application, the use of fully shielded nozzles (e.g. surface cleaners) can significantly lower the emission of aqueous aerosols. De-
pending on the environment to be cleaned, wear a suitable respiratory protective mask of class FFP 2 or comparable to protect yourself from inhaling aerosols if
the use of a fully shielded nozzle is not possible.
Risk of electric shock
DANGER Only connect protection class I de-
vices to properly earthed power sources. Only connect the device to alternating current. The voltage
indicated on the type plate must match the voltage of the power source. Only operate the device via a fault current protection switch (maximum 30 mA). Never touch the mains plug and socket with wet hands. The mains plug and coupling of the extension cable must be water tight and may not be placed in water. The coupling
may not be on the floor. Use cable drums to ensure that the sockets are at least 60 mm above the floor. All live parts in the work area must be protected against water
jets.
WARNING Only connect the device to an
electrical connection which has been set up by a qualified electrician as per IEC 60364-1. Check that the mains connection cable with mains plug is undamaged
each time before using the device. To avoid any possible danger, a damaged mains connection cable must be immediately replaced by the manufacturer, or the au-
thorised customer service department or a qualified electrician. Do not damage the power supply and extension cable by running over it, crushing or yanking it
or similar. Protect the power supply cable from heat, oil and sharp edges. Unsuitable electrical extension cables are dangerous. Only use approved and appropri-
ately marked electrical extension cables with a sufficient line cross section when outdoors: 1-10 m : 1.5 mm2, 10-30 m : 2.5 mm2
CAUTION Always fully unwind the extension
cable from the cable drum. In case of longer breaks in operation and after use, switch off the device at the main switch / device switch and pull the mains plug.

Operation with detergent
WARNING Incorrect use of detergents can
cause serious injuries or poisoning.
CAUTION Keep the detergent out of the
reach of children. Only use the detergents supplied or specified by the manufacturer. The use of other detergents or chemicals can impair the safety of the device.
Care and service
WARNING Always pull out the mains plug
before all care and maintenance work.
CAUTION Have repair work and work on
electrical components carried out by the authorised customer service only.
ATTENTION Do not use acetone, undiluted ac-
ids or solvents, as they corrode the materials used on the device.
Transportation
CAUTION
Risk of accidents and injuries. Take into account the weight of the device for transportation and storage. See chapter Technical data in the operating instructions.
General safety instructions
DANGER Risk of asphyxiation. Keep pack-
aging film out of the reach of children.
WARNING Only use the device for its proper
use. Take into account the local conditions and beware of third parties, in particular children, when working with the device. Persons with reduced physical, sensory or mental capabilities and persons lacking experience and knowledge may only use the appliance if they are properly supervised, have been instructed on use of the appliance safely by a person responsible for their safety, and understand the resultant hazards involved. Children must not operate the device. Children must be supervised to prevent them from playing with the appliance.
CAUTION Safety devices are provided for
your own protection. Never modify or bypass safety devices.

English

Environmental protection
The packing materials can be recycled. Please dispose of packaging in accordance with the environmental regulations. Electrical and electronic devices contain valuable, recyclable materials and often components such as batteries, rechargeable batteries or oil, which – if handled or disposed of incorrectly – can pose a potential danger to human health and the environment. However, these components are required for the correct operation of the device. Devices marked by this symbol are not allowed to be disposed of together with the household rubbish. Cleaning work producing in oily waste water, e.g. washing engines, washing undercarriages etc., may only be performed at washing stations with an oil separator. Working with detergents may only be performed on watertight surfaces with connection to the waste water sewage system. Do not allow detergent to enter waterways or the soil. Extraction of water from public waterways is not permitted in some countries.
Notes on the content materials (REACH) Current information on content materials can be found at: www.kaercher.de/REACH
Intended use
Use the high-pressure cleaner in private households only. The high-pressure cleaner is intended for cleaning machines, vehicles, buildings, tools, façades, terraces, garden machines etc. using a high-pressure water jet.
Accessories and spare parts
Only use original accessories and original spare parts. They ensure that the appliance will run fault-free and safely. Information on accessories and spare parts can be found at www.kaercher.com.
Scope of delivery
The scope of delivery for the appliance is shown on the packaging. Check the contents for completeness when unpacking. If any accessories are missing or in the event of any shipping damage, please notify your dealer.
Device description
The maximum amount of equipment is described in these operating instructions. Depending on the model used, there are differences in the scope of delivery (see packaging). For the figures, please refer to the graphics page Illustration A Illustration B
1 Stand with carrying handle
2 Water connection with built-in strainer
3 Transport wheel
4 Cover
5 Hose guide
6 Trigger “0/OFF” / “I/ON”
7 Storage for spray lances

8 High-pressure hose 9 *Plug ‘n’ Clean detergent bottle 10 Storage / parking position for high-pressure gun 11 Transport handle, extendable 12 Power Control spray lance Dirt grinder for stubborn
contamination, pressure stage: HARD 13 Power Control spray lance Vario Power for the most
common cleaning tasks, pressure stages: HARD / MEDIUM / SOFT / MIX 14 Power Control high-pressure gun 15 Button for separating the high-pressure hose from the high-pressure gun 16 High-pressure gun lever 17 Pressure indicator (0-MIX / 1-SOFT / 2-MEDIUM / 3-HARD) 18 High-pressure gun lock 19 Carrying handle 20 Hose switch 21 High pressure hose reel 22 Crank handle for hose reel 23 Type plate 24 Accessory compartment 25 Hook for net attachment 26 Mesh for accessory compartment 27 Mains connection cable with mains plug 28 Coupling for the water connection 29 *Garden hose (fabric reinforced, diameter at least 1/2 inch (13 mm), length at least 7.5 m, with commercially available quick coupling) 30 *KÄRCHER suction hose for water supply from open containers (order no. 2.643-100) 31 Included screws and dowels
* additionally required
Supplied screws and dowels
Illustration C 1 Stand dowels (2 pieces) 2 Screw 4×22 (2 pieces) 3 Screw 4×16 (10 pieces)

English

Safety devices WARNING
Danger of injury! Serious injuries due to missing, modified or ineffective safety devices. Do not bypass or remove the safety devices and do not render them ineffective. Safety devices are provided for your own protection.
Power switch
The power switch prevents unintentional operation of the device.
High-pressure gun lock
The lock locks the lever of the high-pressure gun and prevents the device from starting unintentionally.
Auto-stop function
If the lever of the high-pressure gun is released, the pressure switch turns off the pump and the high-pressure jet stops. The pump switches on again when the lever is pressed.
Motor circuit breaker
The motor circuit breaker shuts off the device if power consumption it too high.
Symbols on the device
Do not aim the high-pressure jet may at persons, animals, live electrical equipment or the device itself. Protect the device against frost.
The device may not be connected to the public drinking water network.
Installation
For the illustrations, refer to the graphics page. Fit the supplied loose parts onto the device before starting up the device. Have the included screws and the appropriate screwdriver ready.
Fitting the wheels
1. Insert the wheels. Note Pay attention to the alignment of the hole.
Illustration D 2. Secure the wheels with 1 screw each.
Mounting the stand
1. Insert the stand. Illustration E
2. Insert the 2 dowels into the holes as far as they will go.
3. Secure the base with 2 screws.
Mounting the storage for spray lances
1. Hook in the storage for the spray lances. 2. Secure the storage with 2 screws.
Illustration F 3. Secure the cover with 4 screws.
Illustration G
Mounting the transport handle
1. Attach the transport handle. Illustration H

Mounting the accessory net
1. Hang the accessory net on the hooks. Illustration I
Push the high-pressure hose through the hose guide
1. Insert the high-pressure hose through the hose guide from the rear. Illustration J
Installing the water connection coupling
1. Screw the water connection coupling onto the water connection on the device. Illustration K
Initial startup
1. Place the device on a level surface. 2. Completely unwind the high-pressure. 3. Pull the high-pressure hose completely forward
through the hose guide and eliminate any loops and twists. 4. Insert the high-pressure hose into the high-pressure gun until it audibly clicks into place. Note Take care to ensure the correct alignment of the nipple. Illustration L 5. Check the secure connection by pulling on the highpressure hose. 6. Plug the mains plug into a mains socket.
Water supply
For the connection values, see the type plate or chapter Technical data. Observe the water distribution company regulations.
ATTENTION
Damage through contaminated water Contamination in the water can damage the pump and the accessories. KÄRCHER recommends using the KÄRCHER water filter for protection(special accessory, order number 4.730-059).
Connection to the water line
ATTENTION
Hose coupling with Aquastop on the water connection of the device Damage to the pump Never use a hose coupling with Aquastop on the water connection of the device. You can use an Aquastop coupling on the tap. 1. Plug the garden hose onto the water connection
coupling. 2. Connect the garden hose to the water line. 3. Open the water tap fully.
Illustration M
Suck water from open containers
This high-pressure cleaner with the KÄRCHER suction hose is suitable for sucking in surface water, e.g.from water butts or ponds (for maximum suction height, see chapter Technical data). 1. Unscrew the coupling on the water connection. 2. Fill the suction hose with water. 3. Screw the suction hose onto the water connection of
the device and hang it in a water source (e.g. rain barrel).

English

Vent the device
1. Switch the device on “I/ON”. 2. Unlock the lever of the high-pressure gun. 3. Press the lever of the high-pressure gun.
The device switches on. 4. Allow the device for run a maximum of 2 minutes un-
til the water escaping from the high-pressure gun is free of air bubbles. 5. Release the lever of the high-pressure gun. 6. Lock the lever of the high-pressure gun.

Operation
ATTENTION
Risk of damage! Damaging the pump during dry running. Switch off the device if it does not build up pressure within 2 minutes. Proceed according to the instructions in chapter Troubleshooting guide.

Power Control System
The pressure indicator on the high-pressure gun shows the currently set pressure level during operation with a Power Control spray lance. Note The sensitivity of materials can vary greatly depending on age and condition. The recommendations are therefore not binding. Note When operating with surface cleaner and other accessories, the pressure indicator is not accurate.

Display

Pressure stage HARD
MEDIUM

Recommended fore.g.
Stone terraces made of paving stones or washed concrete, asphalt, metal surfaces, garden utensils (wheelbarrow, spade, etc.)
Car/motorcycle, brick surfaces, plastered walls, plastic furniture

SOFT

Wooden surfaces, bicycle, sandstone surfaces, rattan furniture

MIX

Operation with detergent

High-pressure operation
ATTENTION
Damage to painted or sensitive surfaces Surfaces can be damaged when the jet is too close to the surface or an unsuitable spray lance is used. Maintain a minimum spray distance of 30 cm when cleaning painted surfaces. Do not clean car tyres, paint or sensitive surfaces such as wood with the dirt blaster. 1. Insert a spray lance into the high-pressure gun and
lock it into position by turning it 90°. Illustration N

2. Switch the device on (“I/ON”). 3. Unlock the lever of the high-pressure gun. 4. Press the lever of the high-pressure gun.
The device switches on. 5. Turn the Power Control spray lance Vario Power un-
til the required pressure stage is indicated on the pressure indicator.
Operation with detergent
DANGER
Failure to adhere to the safety data sheet Incorrect handling of the detergent can seriously damage your health Observe the safety data sheet of the detergent manufacturer, in particular the instructions on personal protective equipment. Note Detergents may only be added at low pressure. Note A Plug `n’ Clean detergent bottle is required for operating with detergent. KÄRCHER detergents can be purchased ready for use in a Plug ‘n’ Clean detergent bottle. 1. Remove the lid from the Plug ‘n’ Clean detergent
bottle. 2. Press the detergent bottle into the Plug ‘n’ Clean de-
tergent connection with the opening facing downwards. Illustration O 3. Use the Vario Power spray lance. 4. Turn the spray lance in the direction of “MIX” until “MIX” is displayed on the high-pressure gun. During operation, the detergent solution is mixed into the water stream.
Recommended cleaning method
1. Spray the detergent sparingly on the dry surface and let it work for a while (do not let it dry).
2. Rinse off the loosened dirt with the high-pressure jet.
After operation with detergent
1. Pull the Plug ‘n’ Clean detergent bottle out of the holder and close it with the lid.
2. For storage, place the detergent bottle in the holder with the lid facing upwards.
3. Rinse the device with clean water for about 30 seconds.
Interrupting operation
1. Release the lever of the high-pressure gun. When the lever is released, the device switches off. The high-pressure in the system is maintained.
2. Lock the lever of the high-pressure gun. Illustration P
3. Set the high-pressure gun with the spray lance in the parking position.
4. For work breaks longer than 5 minutes, switch off the device “0/OFF”.

English

Ending operation
CAUTION
Danger of injury! Injuries due to uncontrolled water escaping under high pressure. Only disconnect the high-pressure hose from the highpressure gun or the device if there is no pressure in the system. 1. Release the lever of the high-pressure gun. 2. Close the water tap. 3. Press the lever of the high-pressure gun for 30 sec-
onds. The pressure in the system is released. 4. Release the lever of the high-pressure gun. 5. Lock the lever of the high-pressure gun. 6. Switch off the device “0/OFF”. 7. Disconnect the device from the water supply. 8. Pull the mains plug out of the outlet.
Transport CAUTION
Risk of injury and damage! Injury or damage due to non-observance of the weight. Be aware of the weight of the device during transport and storage.
Carrying the device
1. Lift up the device by the carrying handle, and carry it.
Pulling device
1. Pull out the transport handle until it audibly engages. 2. Pull the device by the transport handle.
Transporting the device in a vehicle
1. Before horizontal transport, pull the Plug ‘n’ Clean detergent bottle out of the holder and close it with the lid.
2. Secure the device against shifting and tipping.
Storage CAUTION
Risk of injury or damage due to the weight of the device! Injury and damage. Be aware of the weight of the device during transport and storage.
Storing the device
1. Place the device on a level surface. 2. Disconnect the spray lance from the high-pressure
gun. 3. Press the separation button on the high-pressure
gun and disconnect the high-pressure hose from the high-pressure gun. 4. Without a hose reel: Store the high-pressure hose on the device.
ATTENTION
Damage to the high-pressure hose Damage to the high-pressure hose through incorrect direction of rotation Observe the correct direction of rotation of the hose reel when winding on the hose. 5. With a hose reel: Use the crank handle to turn the
hose reel counterclockwise and wind up the highpressure hose.

6. Stow the mains connection and accessories on the device.
7. Put both spray lances into the storage for the spray lance: a Spray lance dirt grinder: Nozzle downwards b Spray lance Vario Power: Nozzle upwards
Before prolonged storage, observe additional instructions, see chapter Care and service.
Frost protection
ATTENTION
Danger of frost Incompletely emptied devices can be destroyed by frost. Completely empty the device and accessories. Protect the device from frost. The following must be met: The device is disconnected from the water supply. The high-pressure gun is separated from the high-
pressure hose. 1. Switch on the device “I/ON”. 2. Wait a maximum of 1 minute until no more water
comes out of the high-pressure hose. 3. Switch off the device. 4. Store the device with all accessories in a frost-proof
room.
Care and service DANGER
Danger of electric shock Injuries due to touching live parts Switch off the device. Remove the mains plug. The device is maintenance-free, i.e. you do not need to perform any maintenance work.
Clean the sieve in the water connection
ATTENTION
Risk of damage! Damage to the sieve due to improper cleaning. Clean the sieve only under running water against its flow direction. Do not use sharp or hard objectse.g. needles or wire brushes.
ATTENTION
Risk of damage! Damage to the device and accessories when operating without a sieve or with a damaged sieve. Check the sieve for damage before inserting it into the water connection. Replace a damaged sieve immediately. Do not operate the device without a sieve. Clean the sieve in the water connection if necessary. 1. Unscrew the coupling on the water connection. 2. Pull out the sieve.
Illustration Q 3. Clean the sieve under running water. 4. Insert the sieve into the water connection.

English

Troubleshooting guide
Malfunctions often have simple causes that you can remedy yourself using the following overview. When in doubt, or in the case of malfunctions not mentioned here, please contact your authorized Customer Service.
DANGER
Danger of death! Fatal injuries due to electric shock when touching live parts. Do not touch any live parts. Switch off the device. Pull the mains plug out of the mains socket. Device not running 1. Press the lever of the high-pressure gun.
The device switches on. 2. Check that the voltage specified on the type plate
corresponds to the voltage of the power source. 3. Check the mains connection cable for damage. 4. If the motor is overloaded and the motor circuit
breaker has triggered: a Switch off the device “0/OFF”. b Allow the device to cool down for 1 hour. c Switch the device on “I/ON” and resume opera-
tion. Have the device checked by Customer Service if this fault occurs repeatedly. The device does not start up, the motor buzzes Voltage drop due to a weak mains grid or when using an extension cable 1. When switching on, first press the lever on the highpressure gun and then switch on the device “I/ON”. Device does not reach required pressure The water supply is too low. 1. Open the water tap fully. 2. Check the water inlet for an adequate flow rate. 3. Check the setting at the spray lance. 4. Check that the maximum suction height is not exceeded. The sieve in the water connection is dirty. 1. Pull the sieve in the water connection out using flat pliers. 2. Clean the sieve under running water. Illustration Q Air is in the device. 1. Vent the device: a Switch on the device without a connected spray
lance for a maximum of 2 minutes. b Press the high-pressure gun and wait until the
water escaping from the high-pressure gun is free of air bubbles. c Connect the spray lance. Strong pressure fluctuations 1. Cleaning the high-pressure nozzle: a Remove contamination from the nozzle drill with a needle. b Rinse the high-pressure nozzle with water from the front. 2. Check the water supply volume. Device leaking 1. The device leaks a small amount for technical reasons. If the leak is severe, request authorised Customer Service. Detergent is not sucked in 1. Use the Vario Power spray lance and turn it to “MIX”. 2. Check that the Plug ‘n’ Clean detergent bottle is seated in the connection for the detergent with the opening facing down.

Warranty
The warranty conditions issued by our relevant sales company apply in all countries. We shall remedy possible malfunctions on your appliance within the warranty period free of cost, provided that a material or manufacturing flaw is the cause. In a warranty case, please contact your dealer (with the purchase receipt) or the next authorised customer service site. (See overleaf for the address) Further warranty information (if available) can be found in the service area of your local Kärcher website under “Downloads”.
Technical data

K 4 Power Premium Control Power Flex Control Flex

Electrical connection

Voltage

230-240 230-240

Phase

Frequency

Hz 50

Power rating

kW 1,8

1,8

Degree of protection

IPX5 IPX5

Protection class

Power protection (slow- A

blowing)

Water connection

Feed pressure (max.)

MPa 1,2

1,2

Input temperature (max.) °C 40

Input amount (min.)

l/min 9

Suction height (max.)

m 0,5

0,5

Device performance data

Operating pressure

MPa 11

Max. permissible pressure MPa 13

Water flow rate

l/min 6,3

6,3

Maximum flow rate

l/min 7,0

7,0

Detergent flow rate

l/min 0,3

0,3

High-pressure gun recoil N 13

force

Dimensions and weights

Typical operating weight kg 13,7 14,0

Length

mm 405

417

Width

mm 306

306

Height

mm 584

584

Determined values in acc. with EN 60335-2-79

Hand-arm vibration value m/s2 3,2

3,2

Uncertainty K

m/s2 0,8

0,8

Sound pressure level LpA dB(A) 75

Uncertainty KpA

dB(A) 3

Sound power level LWA + dB(A) 91

uncertainty KWA

Exception according to Regulation (EU) 2019/1781 Annex I Section 2 (12): j) Subject to technical changes without notice.

English

Declaration of Conformity
Declaration of Conformity (UK) We hereby declare that the product described below complies with the relevant provisions of the following UK Regulations, both in its basic design and construction as well as in the version put into circulation by us. This declaration shall cease to be valid if the product is modified without our prior approval. Product: High-pressure cleaner Type: 1.324-xxx
Currently applicable UK Regulations S.I. 2008/1597 (as amended) S.I. 2016/1091 (as amended) S.I. 2012/3032 (as amended) S.I. 2001/1701 (as amended) S.I. 2010/2617 (as amended)
Commission Regulation(s) (EU) 2019/1781
Designated standards used EN 60335-1 EN 60335-2-79 EN 62233: 2008 EN 55014-1: 2017 + A11: 2020 EN 55014-2: 2015 EN 61000-3-2: 2014 EN 61000-3-3: 2013 EN IEC 63000: 2018
Applied conformity assessment procedure S.I. 2001/1701 (as amended): Schedule 8
Sound power level dB(A) K 4 Power Control *GB Measured: 88 Guaranteed: 91 K 4 Premium Power Control *GB Measured: 89 Guaranteed: 92 The signatories act on behalf of and with the authority of the company management.

EU Declaration of Conformity We hereby declare that the machine described below complies with the relevant basic safety and health requirements in the EU Directives, both in its basic design and construction as well as in the version placed in circulation by us. This declaration is invalidated by any changes made to the machine that are not approved by us. Product: High-pressure cleaner Type: 1.324-xxx
Currently applicable EU Directives 2006/42/EC (+2009/127/EC) 2014/30/EU 2011/65/EU 2000/14/EC 2009/125/EC
Commission Regulation(s) (EU) 2019/1781
Harmonised standards used EN 60335-1 EN 60335-2-79 EN 62233: 2008 EN 55014-1: 2017 + A11: 2020 EN 55014-2: 2015 EN 61000-3-2: 2014 EN 61000-3-3: 2013 EN IEC 63000: 2018
Applied conformity evaluation method 2000/14/EG: Annex V
Sound power level dB(A) K 4 Power Control *GB Measured: 88 Guaranteed: 91 K 4 Premium Power Control *GB Measured: 89 Guaranteed: 92 The signatories act on behalf of and with the authority of the company management.

Documentation supervisor: S. Reiser Alfred Kärcher SE & Co. KG Alfred-Kärcher-Str. 28 – 40 71364 Winnenden (Germany) Ph.: +49 7195 14-0 Fax: +49 7195 14-2212 Winnenden, 2021/06/01

English

. . ( )
( ) Kärcher .””

Premium Power K 4 Flex Power Control Control

230-240 230-240

50 Hz

1,8

1,8 kW

IPX5 IPX5

()

1,2

1,2 MPa

()

40 C° ()

9 l/min

()

0,5

0,5 m

()

11 MPa

13 MPa

6,3

6,3 l/min

7,0

7,0 l/min

0,3

0,3 l/min

14,0 13,7 kg

417

405 mm

306

306 mm

584

584 mm

EN 60335-2-79

3,2

3,2 m/s2

0,8

0,8 m/s2

75 dB(A) LpA

3 dB(A)

KpA

91 dB(A) + LWA

KWA

. .
. .1 . .2
Q . .3
. .4

.
.

!
. .
. .
. .1
. .2
. . .3 .4
: .”OFF/0″ a . b . “I/ON” c
.
. .1
.”I/ON”
. . .1 . .2 . .3 . .4 . . .1 . .2
Q . : .1 a
. b
. . c
: .1 . a . b
. .2
. .1 .
.”MIX” Vario Power .1 Plug `n’ Clean .2
.

! .
.

. .1 . .2 .3
. : .4
.

. : .5
. . .6 : .7 : a :Vario Power b
.

. .
. :
. .
.”I/ON” .1 .2
. . .3
.4 .

. . .

! .
. . .

!
.
. .

Plug `n’ Clean KÄRCHER . .Plug `n’ Clean
.Plug `n’ Clean .1 .2
.Plug `n’ Clean O
.Vario Power .3 “MIX” “MIX” .4
. .

.1 .( )
. .2

Plug `n’ Clean .1 .
.2 .
. 30 .3

. .1
. . .2
P .3
. 5 .4
.”OFF/0″

!
.
. . .1 . .2
. 30 .3 . . .4 . .5 .”OFF/0″ .6 . .7 . .8

! .
.

. .1

. .1 . .2

‘Plug `n .1 . Clean . .2

! . .
.

Power Control

Power
.Control
. .
.

) (.
/

HARD

. 30
.
. .1
.°90 N .(“I/ON”) .2 . .3 . .4
. Vario Power Power Control .5 .

.
.

. .1 I

.1 . J

.1 .
K

. .1 . .2 .3 . .4
.
. L
.5 .
. .6
.
.

. KÄRCHER
.(059-4.730 ) KÄRCHER

Aquastop
Aquastop .
. Aquastop . .1
. .2 . .3 M

KÄRCHER
) .(
. .1 . .2
.3 .( . )

.”I/ON” .1 . .2 . .3
. .4
. . .5 . .6

C
(2 ) 1
(2 ) 4×22 2
(10 ) 4×16 3

!
. .
.

.
.

. .
.

. .1
. D
. .2

. .1 E . .2 . .3

. .1 . 2 .2
F . 4 .3
G

. .1 H

. .( ) A B 1
2
3
4
5
“OFF” / “I/ON/0” 6
7
8
* 9
/ 10
11
Power Control 12 HARD :
Vario Power Power Control 13 / HARD : MEDIUM / SOFT / MIX
Power Control 14
15
16
-MIX / 1-SOFT / 2-MEDIUM / 3-0) 17 (HARD
18
19
20
21
22
23
24
25
26
27
28
1/2 ) * 29 7,5 ( 13)
(
KÄRCHER * 30 (100-2.643 )
31
*

. .

. .
.
.
.
.
.
(REACH) :
www.kaercher.de/REACH

.
.

. .www.kaercher.com

. .
.

.IEC 60364-1 .
. .
. .
2 2,5 : 30-10 2 1,5 : 10-1 :

.
. /

.
.
.
.

. .

.
.
.
.

. . .
.
.

.
.
. / . / .
. .
. 30 . /

. . . .( )
. . . . .
.

. .EN 12729 Typ BA . .
. . .
.

.° 0

. . / .
( ) .
FFP 2 .

I
. .
. .( 30) . . .
. 60
.

KÄRCHER Home & Garden App
: KÄRCHER Home & Garden App
KÄRCHER :
TM TM
.Google Inc ® ®
.Apple Inc

. . .

.
.

THANK YOU!
MERCI! DANKE! ¡GRACIAS!
Registrieren Sie Ihr Produkt und pro tieren Sie von vielen Vorteilen. Register your product and bene t from many advantages. Enregistrez votre produit et béné cier de nombreux avantages. Registre su producto y aproveche de muchas ventajas.
www.kaercher.com/welcome
Bewerten Sie Ihr Produkt und sagen Sie uns Ihre Meinung. Rate your product and tell us your opinion. Évaluer votre produit et dites-nous votre opinion. Reseñe su producto y díganos su opinión.

www.kaercher.com/dealersearch
Alfred Kärcher SE & Co. KG Alfred-Kärcher-Str. 28-40 71364 Winnenden (Germany)

2-2-SC-A5-GS

Documents / Resources

KARCHER K4 Power Control Flex [pdf] Instruction Manual
K4 Power Control Flex, K4, Power Control Flex, Control Flex, Flex

References

User Manual

K4 Power Control Flex

Specifications

Product Information

Product Usage Instructions

Safety Instructions

Hazard Levels

Operation

Frequently Asked Questions (FAQ)

Q: Can I use this high-pressure cleaner on all surfaces?

Q: How often should I inspect the device for damages?

Documents / Resources

References

Leave a comment

Cancel reply