Kaadas RX-C Touchpad Smart Deadbolt Instruction Manual

Kaadas RX-C Touchpad Smart Deadbolt

 

FIG 1 Install

 

FIG 2 Installation

 

FIG 3 Installation

 

Warning

  • Failure to follow these instructions could result in damage to the product and avoid the factory warranty.
  • The accuracy of the door preparation is critical for the proper functioning and security of this product. Misalignment can cause performance degradation and lessening of security.
  • Finish Care: This lockset is designed to provide the highest standard of product quality and performance. Care should be taken to ensure a long-lasting finish. When cleaning is required use a soft, damp cloth. Using lacquer thinner, caustic soaps, abrasive cleaners or polishes could damage the coating and result in tarnishing.

IMPORTANT: Do not install batteries untill the lock is completely installed on door.

  1. Master PIN Code (4~10 digit): Default master pin code is “12345678”, please modify it after installation. If you forget your master pin code, you can reset your lock back to factory settings.
  2. User PIN Code (4~10 digit): User pin codes can be set up through master pin code. Up to 20 user pin code can be stored.
  3. Both master and user pin codes don’t support the following combination of numbers.

FIG 4 combination of numbers

Definitions

Master Mode

The master mode could be entered by entering[ **+Master PIN Code+# ] to program the lock.

Master PIN Code:

The master pin code is used for programming and for feature settings.

Auto Re-lock:

After successful pin code entry and the unit unlocks, it will automatically re-lock after 30 seconds. This feature is disabled in default setting.

Manual Mode:

Auto re-lock function could be adjusted to manual mode. In manual mode the lock could be locked only by pressing any key for 2 seconds from outside or using thumb turn from inside.

Shutdown Time:

The lock will shutdown for a default of 3 mins and not allow operation after the wrong code entry limit (10 times) has been met. When the unit is in shutdown, the light will flash when you are trying to use keypad.

Silent Mode:

The beeper will not make any voice.

Status indicators: Located on exterior assembly.

User PIN code:

The user pin code operates the lock. Maximum capacity of user pin codes is 20.

Reset button:

After reset operation, the lock will be restored to factory default settings, all user credentials will be deleted. Refer to reset guide.

 

Factory Default settings

FIG 5 Factory Default settings

PdfEditor 4.0.0.14 Testversion – https://www.pixelplanet.com/de/pdfeditor/

 

Lock Operation

Change Master PIN code

  1. Touch the screen with your hand to activate.
  2. Enter “*”twice and the 4-10 digit Master PIN Code followed by “#”.Lock Response:Voice guide.
  3. Enter “1”to change Master PIN Code.Lock Response:Voice guide
  4. Enter new 4-10 digit Master PIN Code followed by “#”.
  5. Repeat step 4 one more time.

warning icon Caution

Before changing default Master PIN Code,all other setting menu will be disabled.You have to change Master PIN Code first,then do other lock settings.

Add up User PIN codes

  1. Touch the screen with your hand to activate.
  2. Enter“*”twice and the Master PIN Code followed by “#”.Lock Response:Digit 1-8 one keypad light up.
  3. Enter “2”Lock Response:All keys on keypad light up.
  4. Enter the User Number to be registered (00-19)followed by “#”.
  5. Enter new User PIN code followed by “#”.
  6. Repeat step 5 one more time.
  7. To continue adding users,do previous steps 4-5 again.

warning icon Caution

When registering User PIN codes,the code must be entered within 10 seconds or time expires.No matter setting succeed or failed,the process won’t completed and stay at current stage,you can press “*”to return to previously menu.

Delete User PIN codes

  1. Touch the screen with your hand to activate.
  2. Enter“*”twice and the Master PIN Code followed by “#”.Lock Response:Digit 1-8 one keypad light up.
  3. Enter “3”Lock Response:All keys on keypad light up.
  4. Enter the User Number (00-19) or User PIN codeto be deleted followed by “#” Lock Response:Voice guide.
  5. To continue deleting users,do previous steps 1-4 again.

warning icon Caution

When deleting User PIN codes,the User Number must be entered within 10 seconds ot time expires.No matter setting succeed or failed,the process won’t completed and stay at current stage,you can press “*” to return to previously menu. Deleting all User PIN codes could be done only by reseting the lock to fatory default settings.

Auto Re-lock enable/disable
Auto Re-lock feature can be programmed through the Master PIN Code or APP.

  1. Touch the screen with your hand to activate.
  2. Enter“*”twice and the Master PIN Code followed by “#”.Lock Response:Digit 1-8 one keypad light up.
  3. Enter “4”Lock Response:Digits 1and 2 on keypad light up.
  4. Enter “1”to enable,enter “2”to disable.Lock Response:Voice guide.

Silent Mode(Speaker enable/disable)
silent Mode feature can only be programmedthrough the Master PIN code or APP.

  1. Touch the screen with your hand to activate.
  2. Enter“*”twice and the Master PIN Code followedby “#”.Lock Response:Digit 1-8 one keypad light up.
  3. Enter “5”to set up languages.Lock Response:Digits 1-6 on keypad linht up.
  4. Enter “1 or 2 or 3 or 4 or 5”to select voice guide language(Silent Mode disable),enter“6” to enable Silent Mode.

Enable Away Mode
Away Mode feature can only be programmedthrough the Master PIN code.

  1. Touch the screen with your hand to activate.
  2. Enter“*”twice and the Master PIN Code followed by “#”.Lock Response:Digit 1-8 one keypad light up.
  3. Enter “6” to enable.

warning icon Caution

In Away Mode,all User PIN code will be disabled temporary,device could be unlocked only by Master PIN code or APP. Away Mode will be disabled automatically after entering Master PIN code or using APP access.If someone unlock the unit by using thumb turn or override key (optional),the speaker will given alarm.

Bluetooth settings
Bluetooth feature can be programmed through th Master PIN code or APP.Bluetooth is disabled in factory default setting.

  1. Touch the screen with your hand to activate.
  2. Enter“*”twice and the Master PIN Code followed by “#”.Lock Response:Digit 1-8 one keypad light up.
  3. Enter “7”to enter Bluetooth settings.
  4. Enter “1”to enter Bluetooth,Bluetooth will work continuously after opration.
  5. Enter “2”to disabled Bluetooth,Bluetooth will shut down in 2 mins after touch keypad lights off for engrgy saving,it will back to work when touch keypad wakes up.

Function extension settings (optional)
Network features are included in function extension,can only be programmed through the Master PIN code.

  1. Touch the screen with your handto activate.
  2. Enter “*” twice and the master PIN Code followed by “#”. Lock response:Digit 1-8 one keypad light up.
  3. Enter “8” to join network.
  4. Enter “1” to log in network.
  5. Enter “2” to log out network.

warning icon Caution

If the lock is connected to a network controller,it is recommended that it is programmed through the centralized user interface(PC or hand-held device)to ensure communication between the lock and the controller.

 

How to use

Unlock the door

    1. Unlock the door from outside Master/User pin code or key.                             Master/User pin code                                                                               FIG 6 Master OR User pin code
    2. Unlock the door from inside Manual thumb turn

FIG 7 Master OR User pin code

Lock the door

  1. Lock the door from outside                                                                                                    Normal                                                                                                                                 In Auto re-lock mode, the bolt will extend out automatically in 5 seconds after unlocking. FIG 8 How to use                                                                                                                                        Manual Mode                                                                                                                   Press any key on keypad for 2 seconds.
  2. Lock the door from inside

Auto Re-lock Mode
In Auto re-lock mode,the device will be locked automatically.

FIG 9 How to use

Unlock with Fake PIN code

8361813719214710
password
Random digits

User can prevent pin code exposure from stangers by entering random digits before or after pin code.

Reset to factory default settings

Operation on lock

  1. Open battery box and keep the lock in “unlock” status.
  2. Open battery box and find the reset button.
  3. Use a sharp thing to press and hold the reset button.
  4. Keep holding the reset button and remove a battery from battery box then replace it.
  5. Keep holding the reset button for another 3 seconds untill voice guide.

 

Read More About This Manual & Download PDF:

Documents / Resources

Kaadas RX-C Touchpad Smart Deadbolt [pdf] Instruction Manual
RX-C Touchpad Smart Deadbolt, RX-C, Touchpad Smart Deadbolt

Leave a comment

Your email address will not be published.