JYTEK PXIe-3117a PXI Express Embedded Controller
USER GUIDE
PXIe-3117a/3115a
PXI Express Embedded Controller
Manual Rev.: 1.0
Revision Date: Aug. 28, 2024
Revision History
| Revision | Release Date | Description of Change(s) |
| 1 | 8/28/2024 | Initial release |
Preface
Copyright © 2024 Shanghai Jianyi Technology Co., Ltd.
This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer.
Disclaimer
The information in this document is subject to change without prior notice in order to improve reliability, design, and function and does not represent a commitment on the part of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
JYTEK is committed to fulfill its social responsibility to global environmental preservation through compliance with the European Union’s Restriction of Hazardous Substances (RoHS) directive and Waste Electrical and Electronic Equipment (WEEE) directive. Environmental protection is a top priority for JYTEK. We have enforced measures to ensure that our products, manufacturing processes, components, and raw materials have as little impact on the environment as possible.
When products are at their end of life, our customers are encouraged to dispose of them in accordance with the product disposal and/or recovery programs prescribed by their nation or company.
Battery Labels (for products with battery)
California Proposition 65 Warning
WARNING: This product can expose you to chemicals including acrylamide, arsenic, benzene, cadmium, Tris(1,3-dichloro-2-propyl)phosphate (TDCPP), 1,4-Dioxane, ane, formaldehyde, lead, DEHP, styrene, DINP, BBP, PVC, and vinyl materials, which are known to the State of California to cause cancer, and acrylamide, benzene, cadmium, lead, mercury, phthalates, toluene, DEHP, DIDP, DnHP, DBP, BBP, PVC, and vinyl materials, which are known to the State of California to cause birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov.
Trademarks
Product names mentioned herein are used for identification purposes only and may be trademarks and/or registered trademarks of their respective companies.
Conventions
Take note of the following conventions used throughout this manual to make sure that users perform certain tasks and instructions properly.
Additional information, aids, and tips that help users perform tasks.
Information to prevent minor physical injury, component damage, data loss, and/or program corruption when trying to complete a task.
Information to prevent serious physical injury, component damage, data loss, and/or program corruption when trying to complete a specific task.
1. Introduction
The JYTEK PXIe-3117a/3115a PXI Express embedded controllers are designed to offer a cost-effective solution for hybrid PXI Express-based testing systems while maintaining strong performance. Based on the 9th and 8th generation Intel® Core™ i7/i5 processors, these controllers deliver reliable computing power suited for a variety of testing and measurement applications at a competitive price point.
The PXIe-3117a/3115a are equipped with multi-core processors that allow the efficient execution of multiple tasks simultaneously in a multi-tasking environment. With auto-configured PCIe switches, these controllers support four x4 or two x8 PXI Express links, providing maximum system throughput of up to 16 GB/s through the PCI Express 3.0 bus.
Featuring up to 64 GB of dual-channel DDR4 memory at 2400 MHz (non-ECC), the PXIe-3117a/3115a are engineered to meet the demands of various applications while optimizing costs. The controllers also come with a range of integrated I/O options, including dual USB 3.2 Gen1 ports (5 Gbps), four USB 2.0 ports, dual 1GbE Ethernet ports for LAN connection and LXI instrument control, and an RS232 port. Advanced PXI trigger functionality is enabled through built-in trigger I/O. The PXIe-3117a, powered by the 9th Gen Intel® Core™ i7-9850HE processor with 6 cores and 12 threads, and the PXIe-3115a, equipped with the 8th Gen Intel® Core™ i5-8400H processor with 4 cores and 8 threads, offer a balance of performance and affordability. These controllers are designed to meet the needs of professionals who require reliable performance in high-stakes testing and measurement scenarios, while optimizing for budget constraints. Whether managing high-speed LAN connections, controlling LXI instruments, or handling peripheral devices, the PXIe-3117a/3115a are ideal for applications where cost-effectiveness and dependable performance are key considerations.
Memory addressing over 4GB is OS-dependent, such that a 32-bit operating system may be unable to address memory space over 4GB. To fully utilize memory, 64-bit operating systems are required.
1.1 Features
PXITM-5 PXI Express Hardware Specification Rev.1.1
PXIe-3117a: Intel® Core™ i7-9850HE
(Base Frequency 2.7 GHz, Turbo Frequency 4.4 GHz)
PXIe-3115a: Intel® Core™i5-8400H
(Base Frequency 2.5 GHz, Turbo Frequency 4.2 GHz)
DDR4-2400MHz SODIMM x2
Default: 16GB, up to 64GB 2400 MHz
Maximum System Throughput 16 GB/s
PXI Express Link Capability
Four Link Configuration: x4 x4 x4 x4
Two Link Configuration: x8 x8
NVME M.2 SSD
Supports 2280 SSD
PCle Gen3 x 4
Integrated I/O
Dual Gigabit Ethernet ports
Two USB 3.2 Ports
Four USB 2.0 Ports
Dual DisplayPort connectors
One COM port (D-sub 9-pin serial)
Trigger I/O for advanced PXITM trigger functions
OS
Microsoft Windows 7/10，Linux 64-bit
Linux (Kernel>5.8)
1.2 Specifications
Processor
Intel® Core™ i7-9850HE/i5-8400H processor
Memory
Two standard 260-pin DDR4 SODIMM sockets
Supports 2400 MHz RAM up to 64 GB total
Supports non-ECC, unbuffered memory
Video
DisplayPort supports up to 3840 x 2160 @ 60Hz resolution
3840 x 2160 @60Hz DisplayPort adapters to other standards are available,w/max.resolutiondependent on adapter. Support only DisplayPort to HDMI and VGA.
DisplayPort adapters for other standards are available, with maximum available resolution dependent on the adapter chosen
Storage
One NVME M.2 500 GB SSD
I/O Connectivity
Dual Gigabit Ethernet controllers through two RJ45 connectors with speed/link/active LED on the faceplate, with both supporting
Wake-on-LAN.
USB
Four USB 2.0 and two USB 3.2 ports on the faceplate.
Trigger I/O
One SMB connector on the faceplate to route an external trigger signal to/from PXI trigger bus
Dimensions (3U PXI module)
3U/4-slot PXI standard
Weight
0.9 kg (exclusive of packaging)
Environmental
Shock and Vibration
Functional shock 30G, half-sine, 11ms pulse duration
Random vibration:
Operating 5 to 500Hz, 0.21Grms, 3 axes
Non-operating 5 to 500Hz, 2.46Grms, 3 axes
Power Requirements
| Operating temperature with SSD | 0 to 55°C |
| Storage temperature | -40 to 71°C |
| Relative humidity, non-condensing | 5 to 95% |
Shock and Vibration
Functional shock 30G, half-sine, 11ms pulse duration
Random vibration:
Operating 5 to 500Hz, 0.21Grms, 3 axes
Non-operating 5 to 500Hz, 2.46Grms, 3 axes
Power Requirements
| Typical Consumption | DC +3.3V | DC +5V | DC +12V | ||||||||||||||||||||||||||||||
| Typical operation (Measured while W10 is idle) |
4.50 A | 0.10 A | 1.94 A | ||||||||||||||||||||||||||||||
| Heavy operation (Measured while W10 is under heavy CPU and storage utilization) |
6.79 A | 4.00 A | 7.32 A | ||||||||||||||||||||||||||||||
1.3 I/O and Indicators
1.3.1 Front Panel
PXI Trigger Connector
The PXI trigger connector is an SMB jack, used to route external trigger signals to or from the PXI backplane. Trigger signals are TTL-compatible and edge sensitive. The PXIe-3117a/3115a provides four trigger routing modes from/to the PXI trigger connector to synchronize PXI modules, including
From a selected trigger bus line to PXI trigger connector
From the PXI trigger connector to a selected trigger bus line
From software trigger to a selected trigger bus line
From software trigger to PXI trigger connector
All trigger modes are programmable by the provided driver.
DisplayPort Connectors
Provides monitor connection for VGA/HDMI monitors; installation of requisite adapters required. Dual display function is also supported.
1.3.2 Reset Button
The reset button, activated by insertion of any pin-like implement, executes a hard reset for the PXIe-3117a/3115a.
1.3.3 LED Indicators
Two LED indicators on the faceplate indicate operational status of the PXIe-3117a/3115a, as follows.
1.3.4 USB 2.0 Ports
The PXIe-3117a/3115a provides four USB 2.0 ports via USB Type-A connectors on the faceplate, all compatible with hispeed, full-speed and low-speed USB devices. Supported boot devices include USB flash drive, USB floppy, USB CD-ROM, and others, with boot priority and device settings configurable in the BIOS.
1.3.5 Gigabit Ethernet Ports
Dual Gigabit Ethernet connection is provided on the PXIe-3117a/3115a front panel.
The Ethernet ports each include two LED indicators, one Active/ Link indicator and one Speed indicator, functioning as follows.
1.3.6 USB 3.2 Ports
The PXIe-3117a/3115a provides two Type-A USB 3.2 ports on the front panel, supporting SuperSpeed, Hi-Speed, full-speed, and lowspeed transmission for downstream. Multiple boot devices, including USB flash, USB external HD, and USB CD-ROM drives are supported, with boot priority configured in BIOS
1.3.8 Onboard Connections and Settings
2. Getting Started
This chapter describes procedures for installing the PXIe-3117a/3115a and making preparations for its operation, includ-ing hardware and software setup. Please note that the PXIe-3117a/3115a is shipped with RAM and SSD preinstalled. Please contact JYTEK or authorized dealer if there are any problems during the installation.
Diagrams and illustrated equipment are for reference only.
Actual system configuration and specifications may vary.
2.1 Package Contents
Before beginning, check the package contents for any damage and ensure that the following items are included:
PXIe-3117a/3115a Controller (equipped with RAM and.
HDD or SSD)
DP to VGA adapter
If any of these items are missing or damaged, contact the dealer from whom you purchased the product. Save the shipping materials and carton in case you want to ship or store the product in the future.
Do not install or apply power to equipment that is damaged or missing components. Retain the shipping carton and packing materials for inspection. Please contact your JYTEK dealer/vendor immediately for assistance and obtain authorization before returning any product.
2.2 Operating System Installation
For more detailed information about the operating system, refer to the documentation provided by the operating system manufacturer.
Preferred/supported operating systems for PXIe-3117a/3115a are:
Windows 7, Windows 10， Linux 64-bit
For other OS support, please contact JYTEK
Most operating systems require initial installation from a hard drive, floppy drive, or CD-ROM drive. The PXIe-3117a/3115a controller supports USB CD-ROM drive, USB flash disk, USB external hard drive, or a USB floppy drive as the first boot device. These devices should be configured, installed, and tested with the supplied drivers before attempting to load the new operating system.
Read the release notes and installation documentation provided by the operating system vendor. Be sure to read all the README files or documents provided on the distribution disks, as these typically note documentation discrepancies or compatibility problems.
1. Select the appropriate boot device order from the BIOS Boot Setup Menu based on the OS installation media used. For example, if the OS is distributed on a bootable installation CD, select USB CD-ROM as the first boot device and reboot the system with the installation CD in the USB CD-ROM drive
2. Proceed with the OS installation as directed and be sure to select appropriate device types if prompted. Refer to the appropriate hardware manuals for specific device types and compatibility modes of JYTEK PXI products.
3. When installation is complete, reboot the system and set the boot device order in the SETUP boot menu accordingly.
2.2.1 Installation Environment
When preparing to install any equipment described in this manual, please refer to Important Safety Instructions.
Only install equipment in well lit areas on flat, sturdy surfaces with access to basic tools such as flat- and cross-head screw-drivers, preferably with magnetic heads as screws and stand-offs are small and easily misplaced.
Recommended Installation Tools include:
Phillips (cross-head) screwdriver
Flat-head screwdriver
Anti-static wrist strap
Anti-static mat
JYTEK PXIe-3117a/3115a system controllers are electrostatically sensitive and can be easily damaged by static electricity. The equipment must be handled on a grounded anti-static mat, and operators must wear an anti-static wristband, grounded at the same point as the anti-static mat.
Inspect the carton and packaging for damage. Shipping and handling may cause damage to the contents. Ensure that all contents are undamaged before installing.
All equipment must be protected from static discharge and physical shock. Never remove any of the socketed parts except at a static-free workstation. Use the anti-static bag shipped with the product to handle the equipment and wear a grounded wrist strap when servicing or installing.
2.2.2 Installing the PXIe-3117a/3115a
1. Remove all screw caps (x4).
2. Release the red locking lever.
3. Depress the latch.
4. Locate the system controller slot on the chassis (Slot 1).
5. Align the controller’s top and bottom edges with the card guides and carefully slide the PXIe-3117a/3115a into the chassis, as shown
6. Elevate the latch until the PXIe-3117a/3115a is fully seated in the chassis backplane. The alignment pin on the rear of the latch can be threaded into the best fit alignment port in the chassis rail.
7. Fasten the four mounting screws on the faceplate and connect all peripheral devices.
2.2.3 Replacing the Hard Drive or Solid State Drive
The PXIe-3117a/3115a provides a NVME M.2 port for optional SSD. Installing an SSD is accomplished as follows.
1. Locate the four screws housing to the PXIe-3117a/3115a controller, as shown.
2. Remove the screws.
3. Gently lift and remove the housing.
4. Locate the four screws (two on each side, as shown) fixing the hard drive, and remove.
5. To install an SSD, reverse the steps and reinstall the PXIe-3117a/3115a into the PXI system.
2.2.4 Replacing the Battery Backup
The PXIe-3117a/3115a is provided with a 3.0 V “coin cell” lithium battery, replacement of which is as follows.
1. Turn off the PXI chassis.
2. Remove the PXIe-3117a/3115a embedded controller from the chassis. Observe all anti-static precautions.
3. To remove the battery, gently insert a small (approx. 5
mm) flathead screwdriver under the battery at the negative retaining clip. Gently pry up and the battery should easily pop out.
4. Place a fresh identical battery (CR2032 or equivalent) in the socket, ensuring that the positive pole (+) is facing upwards. The battery is most easily seated by first being inserted under the positive retaining clip, and then pushed downward at the negative retaining clip. The battery should easily snap into position.
5. Reinstall the embedded controller into the PXI chassis and restore power.
2.2.5 Clearing CMOS
In the event of a system malfunction causing the PXIe-3117a/3115a to halt or fail to boot, clear the CMOS and restore the controller BIOS to its default settings. To clear the CMOS:
1. Shut down the controller operating system and turn off the PXI Chassis.
2. Remove the PXIe-3117a/3115a from the chassis. Observe all anti-static precautions.
3. Locate the CMOS clear switch (SW2) on the board (see Section 1.3.8: Onboard Connections and Settings). Move the switch from Normal position and wait for 5 seconds, then return the switch to Normal position.
4. Remount the controller into the PXI chassis.
5. Press “Delete” to enter the BIOS setup when the splash logo appears.
6. Press “F3” to load Optimized defaults in BIOS setup.
7. Modify the system date and time.
8. Press “F4” to save configuration and exit.
3. Driver Installation
Windows 10 carries most device drivers for the PXIe-3117a/3115a, built-in. Others can be downloaded from the JYTEK PXIe-3117a/3115a Product Page.
After downloading, execute the Setup file, and follow the instructions to complete installation for the following drivers.
Intel® chipset driver
Intel® graphics driver
Intel® Ethernet driver
Intel® RST driver
Intel® ME driver
PXI trigger I/O driver
JYDM (JYTEK Device Manager, please download JYDM from JYPEDIA)
Appendix A – PXI Trigger I/O Function Reference
This appendix describes the use of the PXI trigger I/O function library for the PXIe-3117a/3115a controller, to program routing of trigger signals between the trigger I/O connectors on the faceplate and the PXI trigger bus on the backplane. The API files are located in the installation directory of the PXI Trigger I/O driver.
A.1 Data Types
The PXIe-3117a/3115a library uses the following data types in JYSM_TrigCore.h. It is recommended to use these data types in your application programs. The table below shows the data type names, ranges, and corresponding data types in C/C++, Visual Basic, and Delphi for reference.
A.2 Function Library
This section provides detailed definitions of the functions available in the PXIe-3117a/3115a function library. Each function includes a description, list of supported cards, syntax, parameter list, and return code information.
A.2.1 JYSM_Trig_Open
Description
Initializes the trigger I/O function of the PXIe-3117a/3115a controller. This function must be called before the invocation of any other trigger I/O function.
Syntax C
int JYSM_Trig_Open(const char* systemModuleInstanceName, JYSM_TrigDeviceHandle* hDevice);
Parameter
systemModuleInstanceName: Name of the system module instance.
*hDevice: Device handle.
Return Code
ErrorCode_SystemModuelNotExist: System module does not exist.
ErrorCode_OpenSystemModuleFailed: Failed to open the system module.
A.2.2 JYSM_Trig_Close
Description
Closes the trigger I/O function of the PXIe-3117a/3115a controller, releasing resources allocated for the trigger I/O function. Users must invoke `JYSM_Trig_Close` before exiting the application.
Syntax C
int JYSM_Trig_Close(JYSM_TrigDeviceHandle hDevice);
Parameter
hDevice: Device handle.
Return Code
0: Success
ErrorCode_InvalidHandle`: Invalid handle.
A.2.3 JYSM_Trig_SetConfig
Description
Configures the system module trigger lines.
Syntax C
int JYSM_Trig_SetConfig(JYSM_TrigDeviceHandle hDevice,
JYSM_Trig_Lines line, JYSM_Trig_LineOperatingType opType)
Parameters
hDevice: System module handle.
line: Line to configure.
opType: Line operating type.
Return Code
0: Success
ErrorCode_InvalidHandle: Invalid handle.
A.2.4 JYSM_Trig_GetConfig
Description
Retrieves the configuration of trigger lines.
Syntax C
int JYSM_Trig_GetConfig(JYSM_TrigDeviceHandle hDevice,
JYSM_Trig_Lines line, JYSM_Trig_LineOperatingType* opType);
Parameters
hDevice: System module handle.
line: Line to query.
opType: Pointer to the line operating type.
Return Code
0: Success
ErrorCode_InvalidHandle: Invalid handle.
A.2.5 JYSM_Trig_SetValue
Description
Sets a value to a trigger line.
Syntax C
int JYSM_Trig_SetValue(JYSM_TrigDeviceHandle hDevice,
JYSM_Trig_Lines line, BOOL value);
Parameters
hDevice: System module handle.
line: Line to set the value.
value: Value to set (TRUE or FALSE).
Return Code
0: Success
ErrorCode_InvalidHandle`: Invalid handle.
A.2.6 JYSM_Trig_GetValue
Description
Retrieves the value of a trigger line.
Syntax C
int JYSM_Trig_GetValue(JYSM_TrigDeviceHandle
hDevice, JYSM_Trig_Lines line, BOOL* pValue);
Parameters
hDevice`: System module handle.
line`: Line to query.
pValue: Pointer to store the retrieved value.
Return Code
0: Success
ErrorCode_InvalidHandle: Invalid handle.
A.2.7 JYSM_Trig_SetRouteSignal
Description
Description: Routes trigger signals between trigger lines.
Syntax C
int JYSM_Trig_SetRouteSignal(JYSM_TrigDeviceHandle hDevice,
JYSM_Trig_Lines destLine, JYSM_Trig_Lines sourceLine);
Parameters
hDevice: System module handle.
destLine: Destination line for routing.
sourceLine: Source line for routing.
PXIe-3117a/3115a
Return Code
0: Success
ErrorCode_InvalidHandle: Invalid handle.
A.2.8 JYSM_Trig_GetRouteSignal
Description
Retrieves the routing configuration of trigger lines.
Syntax C
int JYSM_Trig_GetRouteSignal(JYSM_TrigDeviceHandle hDevice,
JYSM_Trig_Lines destLine, JYSM_Trig_Lines* sourceLine);
Parameters
hDevice: System module handle.
destLine: Destination line to query.
sourceLine: Pointer to store the source line.
Return Code
0: Success
ErrorCode_InvalidHandle: Invalid handle.
PXIe-3117a/3115a
Notes
All functions return 0 on success, with various error codes defined for specific failure cases.
The trigger lines (JYSM_Trig_Lines) and operating types (JYSM_Trig_LineOperatingType) are enumerated types that provide predefined values for hardware and software operations.
Appendix B Legacy Boot Mode Settings
UEFI boot mode is default for the PXIe-3117a/3115a BIOS.
To boot in legacy boot mode, change related settings in BIOS menu:
1.Power on and press DEL to enter BIOS menu
2.Move to Boot
3.Select CSM Configuration
4.Under “Boot option filter” select “legacy only”
5.Under “Network” select “Legacy”
6.Under “Storage” select “Legacy”
7.Under “Video” select “Legacy”
8.Under “Other PCI devices” select “Legacy”
9.Press F4 and Enter to save and exit BIOS menu. The system will restart and apply settings for Legacy boot mode.
To restore UEFI boot mode:
1.Power on and press DEL to enter BIOS menu
2.Press F3 and Enter to load optimized defaults
3.Press F4 and Enter to save and exit BIOS menu
The system restarts and default settings for UEFI boot mode are applied.
This page intentionally left blank.
Important Safety Instructions
For user safety, please read and follow all instructions, Warnings, Cautions, and Notes marked in this manual and on the associated device before handling/operating the device, to avoid injury or damage.
S’il vous plaît prêter attention stricte à tous les avertissements et mises en garde figurant sur l’appareil , pour éviter des blessures ou des dommages.
Read these safety instructions carefully
Keep the User’s Manual for future reference
Read the Specifications section of this manual for detailed information on the recommended operating environment
The device can be operated at an ambient temperature of 50ºC
When installing/mounting or uninstalling/removing device; or when removal of a chassis cover is required for user servicing (See “Getting Started” on page 17.):
Turn off power and unplug any power cords/cables
Reinstall all chassis covers before restoring power
To avoid electrical shock and/or damage to device:
Keep device away from water or liquid sources
Keep device away from high heat or humidity
Keep device properly ventilated (do not block or cover ventilation openings)
Always use recommended voltage and power source settings
Always install and operate device near an easily accessible electrical outlet
Secure the power cord (do not place any object on/over the power cord)
Only install/attach and operate device on stable surfaces and/or recommended mountings
If the device will not be used for long periods of time, turn off and unplug from its power source
Never attempt to repair the device, which should only be serviced by qualified technical personnel using suitable tools
A Lithium-type battery may be provided for uninterrupted backup or emergency power.
Risk of explosion if battery is replaced with one of an incorrect type; please dispose of used batteries appropriately.
The device must be serviced by authorized technicians when:
The power cord or plug is damaged
Liquid has entered the device interior
The device has been exposed to high humidity and/or moisture
The device is not functioning or does not function according to the User’s Manual
The device has been dropped and/or damaged and/or shows obvious signs of breakage
Disconnect the power supply cord before loosening the thumbscrews and always fasten the thumbscrews with a screwdriver before starting the system up
It is recommended that the device be installed only in a server room or computer room where access is:
Restricted to qualified service personnel or users familiar with restrictions applied to the location, reasons therefor, and any precautions required
Only afforded by the use of a tool or lock and key, or other means of security, and controlled by the authority responsible for the location
BURN HAZARD
Touching this surface could result in bodily injury.
To reduce risk, allow the surface to cool before touching.
Getting Service
Contact us should you require any service or assistance.
Shanghai Jianyi Technology Co., Ltd.
Web Site http://www.jytek.com
Address: 上海市浦东新区张江高科技园区芳春路300号
300 Fang Chun Rd., Zhangjiang Hi-Tech Park, Pudong
New Area, Shanghai,201203,China
Tel: +86-21-5047-5899
Email: service@jytek.com
Specifications
- Product: PXIe-3117a/3115a
- Type: PXI Express Embedded Controller
- User’s Manual Revision: 1.0
- Revision Date: Aug. 28, 2024
FAQ
Q: What operating systems are compatible with the PXIe-3117a/3115a?
A: The controller supports 64-bit operating systems to fully utilize memory addressing over 4GB.
Documents / Resources
 |
JYTEK PXIe-3117a PXI Express Embedded Controller [pdf] User Manual PXIe-3117a PXI Express Embedded Controller, PXIe-3117a, PXI Express Embedded Controller, Embedded Controller, Controller |
