DENBIG Portable Air Conditioner

I. Notes

Thank you for choosing the luxurious and elegant mobile air conditioning. Please keep the manual for later review, and read the manual carefully before use.

• The air conditioning is only suitable for indoor use, and is not suitable for other applications.
• Follow local grid interconnection rules while installing the air conditioning and ensure that it is properly grounded. If you have any question on electrical installation, follow the instructions of the manufacturer, and if necessary, ask a professional electrician to install it.
• Place the machine in a flat and dry place and keep a distance of above 50cm between the machine and the surrounding objects or walls.
• After the air conditioning is installed, ensure that the power plug is intact and firmly plugged into the power outlet, and place the power cord orderly to prevent someone from being tripped or pulling out the plug.
• Do not put any object into the air inlet and outlet of the air conditioning. Keep the air inlet and outlet free from obstructions.
• When drainage pipes are installed, ensure that the drainage pipes are properly connected, and are not distorted or bended.
• While adjusting the upper and lower wind-guide strips of the air outlet, pluck it with hands gently to avoid damaging wind-guide strips.
• When moving the machine, make sure that it is in an upright position.
• The machine should stay away from gasoline, flammable gas, stoves and other heat sources.
• Do not disassemble, overhaul and modify the machine arbitrarily, otherwise it will cause a machine malfunction or even bring harm to persons and properties. To avoid danger, if a machine failure occurs, ask the manufacturer or professionals to repair it.
• Do not install and use the air conditioning in the bathroom or other humid environments.
• Do not pull the plug to turn off the machine.
• Do not place cups or other objects on the body to prevent water or other liquids from spilling into the air conditioning.
• Do not use insecticide sprays or other flammable substances near the air conditioning.
• Do not wipe or wash the air conditioning with chemical solvents such as gasoline and alcohol. When you need to clean the air conditioning, you must disconnect the power supply, and clean it with a half-wet soft cloth. If the machine is really dirty, scrub with a mild detergent.
• The appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and maintenance shall not be made by children without supervision.
• Risk Of Fire Or Explosion. Flammable Refrigerant Used. To Be Repaired Only By Trained Service Personnel. Do Not Puncture Refrigerant Tubing.
• Risk Of Fire Or Explosion. Dispose Of Properly In Accordance With Federal Or Local Regulations. Flammable Refrigerant Used.

II. Features and Components

1. Features

New look, compact structure, streamlined machine, aristocratic atmosphere.

With cooling, heating (single cold without heating function), dehumidification and fan function, Continuously Water Drainage Functions.

Automatic swing leaf in the outlet has automatic air swing function, and the outlet can be covered when the machine is turned off to prevent dust from entering the body.

LCD displays the control panel. The machine is beautiful and elegant. High-quality LCD remote control is equipped to facilitate operation.

Handles on both sides adopt dividing point design, so that it is easier to carry it and the body design is more humane.

The structure of wrapping the power cord on the back facilitates users to hang the power cord without hanging it down to the ground and staining and damaging the power cord.

Outdoor interface is set high to facility assembly and keep the smooth flow of the heat pipe.

Air filtration capability.

Timing switch function.

Protection function of automatically restarting the compressor after three minutes, with a variety of other protection functions.

Use the unit in the recommended room size:

• 5,000 BTU (SACC standard) up to 150 sq. ft.
• 6,000 BTU (SACC standard) up to 250 sq. ft.
• 7,000 BTU (SACC standard) up to 300 sq. ft.
• 8,000 BTU (SACC standard) up to 350 sq. ft.
• 10,000 BTU (SACC standard) up to 450 sq. ft.
• 11,000 BTU (SACC standard) up to 500 sq. ft.

2. Components:

A diagram shows the components of the portable air conditioner. The main unit includes:

• 1. Top cover
• 2. Control panel
• 3. Air outlet louvers
• 4. Left side panel
• 5. Base
• 6. Caster
• 7. Front housing
• 8. Right side panel
• 9. Rear housing
• 10. Winding column
• 11. Air vent
• 12. UP CON Filter
• 13. Under CON Filter
• 14. Drainage hole

Additionally, the following assemblies are shown:

• Exhaust Pipe Assembly
• Window Sealing Plate Assembly

III. Control Setting

1. Control panel operation instructions

1) Operation Interface:

The control panel features several buttons and indicators:

• 1. POWER: Turns the unit on and off.
• 2. MODE: Selects between Cooling, Fan, and Dry modes. Dry mode offers dehumidification capacity up to 45 pints/24 hours.
• 3. SLEEP: Activates Sleep mode in Cooling Mode for energy-saving and quiet operation.
• 4. DOWN: Decreases temperature or timer setting (not available in FAN or DEHUMIDIFYING modes). Target temperature range: 61°F – 88°F (16°C – 31°C).
• 5. UP: Increases temperature or timer setting (not available in FAN or DEHUMIDIFYING modes). Target temperature range: 61°F – 88°F (16°C – 31°C).
• 6. SPEED: Selects high or low wind speed in Cooling and Fan modes. Unavailable in Dehumidifying mode.
• 7. TIMER: Sets automatic ON/OFF timer in 1-24 hour increments.
• 8. Display Window: Shows set temperature (Fahrenheit or Celsius) or remaining time for a time delay.

2. Operation instructions of remote control

The remote controller has the following buttons:

• 1. Power: Turns the machine on or off.
• 2. Timer: Sets the timing value.
• 3. Down: Reduces temperature and timing set value.
• 4. Mode: Switches between cooling, air supply, and dehumidification modes.
• 5. Up: Increases temperature and timing set value.
• 6. Fan: Selects high or low wind speed.
• 7. Sleep Mode: Turns on the sleep mode.

NOTE: Requires AAA 1.5VDC battery (not included).

IV. Protection function

• 4.1 Frost Protection Function: If the exhaust pipe temperature is too low in cooling, dehumidification, or sleep mode, the machine enters protection status. It reverts to normal operation when the temperature rises.
• 4.2 Overflow Protection Function: When the water pan exceeds the warning level, an alarm sounds, and the display shows "FL". Empty the water pan via the drainage pipe or water outlet. The machine returns to its original state after emptying.
• 4.3 Automatic Defrosting: (Heating and cooling models) The heating symbol flashes on the display during defrosting.
• 4.4 Automatic Thermal Protection: In heating mode, the compressor and lower motor stop during protection to preserve service life. They resume normal operation once the temperature recovers.
• 4.5 Protection Function of the Compressor: A 3-minute delay booting protection function is implemented to increase the compressor's service life after it has been turned off.

V. Installation and adjustment

1. Installation

Warning: Before using the mobile air conditioning, keep it upright for at least two hours. Ensure the unit is in an upright position and placed on a flat surface during movement. Do not install or use in bathrooms or other humid environments.

1.1 Install the heat pipe assembly

A diagram illustrates the installation of the heat pipe assembly.

1. Remove the outer connector assembly and the exhaust pipe assembly, and take off the plastic bags.
2. Insert the heat pipe assembly (exhaust joint end) into the back panel vent slot (push to the left) to complete the assembly.

1.2 Installation of window sealing plate components

Diagrams show window sealing plate assembly installation.

1. Half open the window and mount the window sealing plate assembly to the window. Components can be placed horizontally or vertically.
2. Extend the components of the window sealing plate assembly, adjust their opening distance to contact the window frame, and secure them.

Notes for window sealing plate assembly:

• The flat end of the exhaust pipe joints must snap into place.
• The pipe should not be distorted or turned more than 45°. Keep the exhaust pipe ventilation unblocked.

1.3 Install the unit

Diagrams show unit placement and exhaust pipe connection.

1. Move the machine with the installed heat pipe and fittings in front of the window. Ensure a minimum distance of 50 cm between the unit, walls, or other objects.
2. Elongate the exhaust pipe and snap the flat end of its joints into the hole of the window sealing plate assembly.

Notes:

• The flat end of the exhaust pipe joints must snap into place.
• The pipe cannot be distorted or turned more than 45°. Keep the ventilation of the exhaust pipe unblocked.

VI. Drainage Instructions

1. Manual drainage:

When the machine stops due to a full water pan:

1. Turn off the machine power and unplug the power plug. Move the machine carefully to avoid spilling water.
2. Place a water container below the side water outlet at the back of the unit.
3. Unscrew the rotary knob and unplug the rubber stopper. Water will flow into the container.

Notes:

• Keep the rotary knob and rubber stopper properly.
• The body can be tilted slightly backward during drainage.
• If the water container cannot hold all the water, re-insert the rubber stopper promptly to prevent spillage onto the floor or carpet.

After drainage:

1. Re-insert the rubber stopper and tighten the rotary knob.

Note: Restart the machine only after the rubber stopper and rotary knob are installed correctly to prevent condensate water from flowing onto the floor or carpet.

Diagrams show the rubber stopper and exhaust water tube.

2. Continuous drainage (for cooling and dehumidification modes):

Diagrams show the continuous drainage setup.

1. Unscrew the rotary knob and unplug the rubber stopper.
2. Insert the drainage pipe into the water outlet.
3. Connect the drainage pipe to a bucket or suitable drainage area.

VII. Maintenance

Cleaning: Before cleaning and maintenance, turn off the machine and unplug the power plug.

1. Clean the surface

Clean the machine surface with a wet soft cloth. Do not use chemicals like benzene, alcohol, or gasoline, as they can damage the surface or the entire machine.

2. Clean the filter screen

If the filter screen is clogged with dust, reducing effectiveness, clean it every two weeks.

3. Clean the upper filter screen frame

1. Unscrew the screw fixing the EVA filter net and back shell, and remove the EVA filter net.
2. Wash the EVA filter screen in warm water with neutral detergent (approx. 40°C / 104°F) and dry it in the shade after rinsing.

Postseason Storage:

1. Unscrew the rotary knob, unplug the rubber stopper, and drain the water from the water pan into other containers or by tilting the body.
2. Turn on the machine, set it to low-wind ventilation mode, and maintain this state until the drainage pipe is dry to prevent mildew inside the body.
3. Turn off the machine, unplug the power plug, wrap the power cord, and re-install the rubber stopper and rotary knob.
4. Remove and properly store the exhaust pipe.
5. Cover the air conditioner with a plastic bag and store it in a dry place, out of reach of children. Take dust control measures.
6. Remove batteries from the remote control and store them properly.

Note: Ensure the unit is placed in a dry place and all components are kept properly.

VIII. Troubleshooting

Do not repair or disassemble the air conditioning yourself. Unqualified repair may void the warranty and cause damage to users or their properties.

If problems not listed in the table occur or recommended solutions do not work, please contact the professional service organization or contact denbigofficial@hotmail.com.