Glomp Toilet Installation Guide

General Installation Notes

Note: All measurements for installation must be taken from the finished wall/floor and toilet. Listed measurements are indicative only.

Wet room protection is carried out based on industry regulations.

Product Variants and Components

The Glomp toilet system is available in several configurations:

• Model 333241: Glossy white
• Model 333282MH: Matt white
• Model 333284MG: Matt gray
• Model 333171MS: Matt black

Available finishes for the toilet unit include:

• Chrome (Art. No: 57231)
• Matt black (Art. No: 57232)
• Solid brass (Art. No: 57234)
• Stainless steel (Art. No: 57235)

Installation Requirements

Required Purchase: The toilet seat is not included in the delivery and must be purchased separately.

Necessary Tools: Specific tools are required for installation (details not specified in this document).

Not Included: The built-in cistern and flush button are not part of this delivery and must be purchased separately.

Optional Compatibility: This toilet system is compatible with the Geberit Duofix Sigma 112 cm built-in cistern.

Important Installation Advice

Important: It is recommended to set the built-in cistern to 4.5 liters. Using a larger water volume or excessively high pressure can cause splashing issues. This can be resolved by installing the supplied water pressure reducer (detail A). This toilet is not recommended for use with low-capacity installation cisterns that cannot provide stable performance.

Main Toilet Installation Steps

Step 5A: Mounting Dimensions

Diagram Description: Illustrates the required mounting dimensions and shows the placement of threaded bolts on the wall.

Action: Install the threaded bolts as shown in the diagram.

Step 5B: Water Pressure Reducer Installation

Diagram Description: Shows the installation of the supplied water pressure reducer (detail A) into the cistern's pipe system.

Action: Install the supplied water pressure reducer (detail A).

Step 5C: Toilet Mounting and Securing

Diagram Description: Depicts the installation of the built-in cistern's flush pipe and drain pipe, insertion of mounting bushings (detail B) into the toilet's mounting holes, placement of the toilet onto the threaded bolts, and tightening of screws with an Allen key. It also shows the application of sanitary silicone.

Action:

• Install the built-in cistern's flush pipe and drain pipe according to its specific installation instructions.
• Insert the mounting bushings (detail B) into the toilet's mounting holes.
• Place the toilet onto the threaded bolts.
• Tighten the screws in the mounting bushings through the toilet seat holes using the provided Allen key.
• Apply an acid-free sanitary silicone sealant between the toilet and the wall for a watertight seal.

Soft Close Toilet Seat Assembly

Note: Some of the drawings may differ slightly from the delivered toilet seat.

Step 8A: Hinge Installation

Diagram Description: Shows the hinges being installed into the toilet bowl.

Action: Install the hinges in the toilet bowl.

Step 8B: Initial Screw Tightening

Action: Loosely tighten the screws for the hinges.

Step 8C: Attaching the Seat

Diagram Description: Depicts the toilet seat being attached to the installed hinges.

Action: Attach the toilet seat to the hinges.

Step 8D: Seat Alignment Adjustment

Diagram Description: Shows the toilet seat being adjusted by sliding it forward/backward and sideways to ensure its edge is flush with the toilet bowl.

Action: Adjust the toilet seat by sliding it back and forth as well as sideways until the edge of the toilet seat is flush with the toilet bowl.

Step 8E: Detaching the Seat

Diagram Description: Illustrates the process of detaching the toilet seat from the hinges. A note indicates the click function might vary.

Action: Click the seat off. (Note: The clicking function may differ from what is shown in the drawing.)

Step 8F: Final Screw Tightening

Action: Now, tighten the screws very firmly.

Step 8G: Installing Cover Caps

Action: Install the cover caps over the hinge mechanisms.

Step 8H: Final Seat Installation

Action: Install the toilet seat onto the secured hinges.