JUNLI T9 Projector Instruction Manual

JUNLI T9 Projector

• Mirror/sync with Android:
  On the projector, go to “APPS” and select “Miracast”. On your mobile device, scan the EShareServer QR code. You might need to install the software when using it for the first time, and select the Miracast ID number to start mirroring.
• Mirror/sync with iPhone:
  On the projector, go to “APPS” and select “AirScreen”. On your iPhone, select the screen mirroring icon.

How to Screen cast with Android/iPhone (Miracast):

Make sure the phone and the projector is connected to the same Wi-Fi network. On the projector, go to ‘APPS’ and select ‘Miracast’. On your mobile device, select the screencast icon to find your projector name. The icon can look as follows depending on the software.

Product Specifications

Correct disposal of the products: Within the European Union, this symbol indicates that the products must not be disposed of in household waste. Devices contain valuable recyclable materials that should be recycled for reuse and uncontrolled waste disposal may cause harm to the environment and human health. Please dispose of old products via suitable collection systems or send the unit to the office where you bought it. This will ensure proper product recycling.

Distance and screen size

Warnings and Safety precautions

• Be sure to use the supplied power adapter of the device. Improper use of different power adapters will cause serious damage to the device;
• If you do not use the device for a long time, please make sure to turn off the power switch;
• Please avoid particles entering or blocking the air outlet at the fan outlet;
• When the device is operating, please do not turn off the power directly;
• When connecting an external device with a large power consumption, please confirm whether the power supply can support it;
• Do not open the device;
• Do not look directly into the lens;
• Do not expose this unit to water or moisture;
• Do not install in hot and humid places;
• Do not install in poorly ventilated places;
• Do not install in dusty and smoky places;
• Do not block ventilation holes (inlet or outlet);
• Position the device at least 30cm away from any obstacle, ceiling and wall;
• After this product is scrapped, it should be treated as waste electrical and electronic products, and the corresponding waste electronic products should be recycled. This product is not suitable for the disposal of ordinary garbage.

FCC STATEMENT

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
   1. This device may not cause harmful interference.
   2. This device must accept any interference received, including interference that may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.

Troubleshooting

• Wi‑Fi network not appearing in the list: Refresh the page and try selecting Settings> Network > WLAN again.
• Mirroring/screen casting not starting: Confirm your phone and projector are connected to the same Wi‑Fi network before starting mircast (Android), airscreen (iPhone), or Miracast.
• First-time mirroring app issues on Android: When scanning the EShareServer QR code, you may need to install the software the first time you use it.