JOYO JW-06 Digital Wireless Transmitter and Receiver
Product Information
Specifications
- Compliance: Part 15 of FCC Rules
- RF Exposure: Meets general requirements
Product Usage Instructions
Safety Precautions
- Caution: Any changes or modifications not approved by the manufacturer could void the device’s operation authority.
Operating Conditions
- This device complies with FCC Rules Part 15. It must not cause harmful interference and should accept any received interference.
RF Exposure
- The device has been evaluated to meet the general RF exposure requirements for safe usage.
FAQ (Frequently Asked Questions)
Q: Can I make modifications to the device?
A: No, any changes or modifications not explicitly approved by the manufacturer could void your authority to operate the equipment.
Q: What are the operating conditions for this device?
A: The device complies with Part 15 of the FCC Rules, meaning it should not cause harmful interference and must accept any received interference.
Important Notes
- Do not disassemble or repair this product by yourself.
- Do not use or store it in any heat sources, or damp, dusty areas.
- Avoid violent vibrations or shock.
- Do not drop this product otherwise, it may malfunction.
- Do not use alcohol or other cleaning fluids to clean this product.
- This product works normally only when the transmitter and the receiver pair up. it supports one-to-one and one-to-many.
- Please make sure the transmitter and the receiver keep a distance away from the wireless router or other wireless pieces of equipment during use.
- Obstructions between the transmitter and the receiver may affect the transmission distance.
- A maximum of 4 sets of transmitters and receivers can be used in the same place simultaneously.
- If the red indicator flickers during use, it indicates a low battery, please charge it in time.
- Please turn off the transmitter and the receiver when not in use.
- Due to one of the characteristics of lithium battery, there is a slight self-discharge. Therefore please charge the battery in 2 months to avoid low battery protection.
- The lithium battery capacity decreases gradually after repeated charge and discharge, so this product’s lifetime will be affected within an acceptable degree with time.
Parameters
- 48K/24bit audio resolution
- Delay time: <6mS
- Transmission distance> 20m
- Frequency response: 10Hz-22KHz+-1dB
- Distortion: <0.02%(@1KHz-10dBFS)
- Wireless frequency band: 5.8GHz ISM frequency band.
- Anti-interference method: Frequency hopping
- Channel bank’s quantity: 4
- Built-in lithium battery: Over 5 hrs battery life once fully charged
Specifications
- Battery: Rechargeable lithium battery 3.7V/500mAh
- Frequency response: 10Hz-22KHz
- Wireless frequency band: 5.8GHz ISM frequency band
- Dimensions: 84*100*46mm
- Attached accessories: Owner’s manual, USB cable
Product diagram and introduction
How to use?
- Check up the battery level of the charging case/ start charging
- You can start charging by pressing the charging control button, and it indicates the battery level of the charging case
- You can start charging by pressing the charging control button, and it indicates the battery level of the charging case
- Charge the charging case
- Charge other portable devices via the charging case
- Charge the transmitter and receiver
- If the LED indicator flickers in red, it means low battery(pls charge it).
- Both the transmitter and receiver will be charged automatically once you plug them into the charging case, till fully charged.
- Both the LED indicators of the transmitter and receiver are in red during charging.
- The LED indicators go out once fully charged.
- Pair up all over again— double-click the buttons
- Double-click the receiver button first, and it will flicker in red and blue alternately
- Then double click the transmitter’s button first, and it will flicker in red and blue alternately About 2 seconds later, if both of their indicators indicate blue, it means they paired successfully
- Switch the Channel banks
- Tap the button once, and you can switch to 1 Channel bank.
- The red indicator’s flicker times indicate the current Channel bank.
- Instructions for the wireless system
- Long press the button to turn on the unit.
- Connect the transmitter to the guitar.
- Connect the receiver to the amp/mixer.
- Connect the transmitter to the guitar
- Suitable for all electric guitars, including Stratocaster style electric guitars with vibrato system.
- Connect the receiver to the amp
- Switch on the receiver, if its blue indicator is on, it indicates the receiver and transmitter are paired.
- If the blue indicator is flickering, it indicates they’re not paired, it might be due to strong signal interference, exceeds transmission distance or the transmitter doesn’t work.
JOYO TECHNOLOGY CO., LTD
- Address: 2/F, Lushi Industry Building, 28th District, Bao’an, Shenzhen, 518101 China.
- www.joyoaudio.com Email: info@joyoaudio.com Tel: 0086-755-29765381
Documents / Resources
 |
JOYO JW-06 Digital Wireless Transmitter and Receiver [pdf] Owner's Manual JW-06 Digital Wireless Transmitter and Receiver, JW-06, Digital Wireless Transmitter and Receiver, Wireless Transmitter and Receiver, Transmitter and Receiver, Receiver |
