JBC Tools CS-9F Precision Desoldering Station Instruction Manual

Includes: CS Control Unit, Micro Desoldering Iron, Power Cord, Sponge, Brass Wool, DS360 Accessories, C360 Tips, Filters, Cleaning Brush, Solder Collector, Cleaning Rods, Electric Desoldering Module, Filter Set, Cotton Filter Set, Suction Filter, Module Cable, Manual

Packing List

The following items are included:

Features and Connections

Adjust. Tool Holder:The position of the tool holder (ref. 0014720) can be easily adjusted by loosening or tightening the knob.

Cable Collector: The cable collector (ref. CC1001) keeps the cable away from the work area and prevents the cable from disturbing the operator while soldering.

Insert the cable into the cable collector clip. Do not leave the cable longer than necessary to reach the work area freely
The cable collector is flexible. It accompanies and adapts to the movements during the soldering process

Tip Cleaner

Select the option to suit your needs and improve the thermal transfer of the tip.

Wool/Brush Replacement

not included, sold separately

Tip Care

Note: Do not press the vacuum pump button while tinning the desoldering tip, as the fumes given off by the flux would quickly block the ducts and the air filter.

Changing Tips

Note: This operation should be carried out while the tip is hot and at a minimum temperature of 250°C so that any tin left inside is still molten

To remove the tip, use a pair of flat-nosed pliers, twist the tip and pull.
To fasten the tip, do not hold it on the spring clamp. Place the pliers directly in front of the spring.

Cleaning Tips

Choose the cleaning rod diameter according to the tip size. Put the rod at the tip and gently move it back and forth while turning it slightly. The tip hole should be periodically cleaned.
Note: Let the tool cool down before performing this operation.

Choose the cleaning rod diameter according to the tip size. Put the rod at the tip and gently move it back and forth while turning it slightly

Compatible Tips

The CS station works with C360 tips and DS360 irons. Find the model that best suits your needs at www.jbctools.com

Desoldering Process

When desoldering, use a tip with a diameter larger than the pad being desoldered. This will achieve maximum suction and thermal efficiency.
Place the tip with the component terminal in the hole.

Place the tip with the component terminal in the hole.

The vacuum pump will continue to run for a few seconds. This makes sure that the vacuum circuit is completely empty. If there is any solder remains left on a terminal, just resolder it with fresh solder and repeat the desoldering operation.

Desoldering Iron Maintenance

Note: For the following operations, turn off the station or disconnect the tool and wait until the tool temperature drops to room temperature.

Changing the Heating Element

Cleaning the Solder Collector

Note: For this operation, turn off the station or disconnect the tool and wait until the tool temperature drops to room temperature

Electric Desoldering Module

Note: Before carrying out maintenance, always unplug the equipment. If there is a loss of suction, check that there is no obstruction in the tool (tip, heating element, tool filter), tube or suction filters.

Changing Pump Filters

Periodically check the filters and replace them if they are yellowish. Note: Do not use sharp pointed objects to open the suction filter

Operation

JBC’s Most Efficient Soldering System. This revolutionary technology is able to recover tip temperature extremely quickly. This allows the user to work at a lower temperature. As a result, tip life is five times longer than with other brands

Select temperature between 90 and 450 ºC using:

Change Sleep temperature and set Sleep delay from 0 to 9 min or no Sleep.
Change Hibernation delay from 0 to 60 min or no Hibernation.

Control Process

Troubleshooting

Station troubleshooting available on the product page on www.jbctools.com.

Parameters

Be careful when using these parameters as they may reduce the tip life if not used properly. Please follow the recommended guidelines:

Station Settings

Tool Settings

Compact Station Firmware Update
Compact stations can be updated via its USB-B connector by means of the USB connection cable. The firmware update file can be downloaded from www.jbctools.com/software.html.

FAQs

Q: How do I clean a very dirty tip?

A: If the tip is very dirty, before using the brass wool, it is recommended to first clean the tip with CL7984 Wiper to remove excess solder.

Q: What is included in the Cotton Filter Set?

A: The Cotton Filter Set includes 10 filters to help with desoldering tasks.

Q: How does the cable collector help during soldering?

A: The cable collector keeps the cable away from the work area, preventing it from disturbing the operator while soldering and adapting to movements during the process.

Documents / Resources

JBC Tools CS-9F Precision Desoldering Station [pdf] Instruction Manual
CS-9F, CS-9F Precision Desoldering Station, Precision Desoldering Station, Desoldering Station

References

User Manual

CS-9F Precision Desoldering Station

Specifications