重要な安全情報
Please read and understand all safety warnings and instructions before operating the FOTING Pressure Washer Surface Cleaner Attachment. Failure to follow these instructions may result in serious injury or property damage.
- Always wear appropriate personal protective equipment (PPE), including eye protection, gloves, and sturdy footwear, during operation.
- 高圧洗浄機を起動する前に、すべての接続が安全で漏れがないことを確認してください。
- Never direct the high-pressure spray at people, pets, or electrical equipment.
- 操作エリアに子供や傍観者を近づけないでください。
- Do not exceed the maximum pressure of 4000 PSI or maximum water temperature of 140°F (60°C).
- Always refer to your pressure washer's instruction manual for additional safety guidelines and operating procedures.
- Disconnect the attachment from the pressure washer and release all pressure before performing any maintenance or cleaning.
パッケージ内容
以下にリストされているすべてのアイテムがパッケージに含まれていることを確認してください。
- 1 x FOTING 15-inch Pressure Washer Surface Cleaner Attachment
- 1 x 16-inch Extension Wand
- 2 x Replaceable Nozzles
- 4 x Replacement O-Rings
- クリーニングニードル x 1
- 防水テープ1本
Figure 2: Package Contents - FOTING 15-inch Surface Cleaner, 16-inch Extension Wand, Nozzles, O-Rings, Cleaning Needle, and Waterproof Tape.
仕様
| 特徴 | 仕様 |
|---|---|
| 最大圧力 | 4000PSI |
| 最大流量 | 3.0 GPM |
| 最高水温 | 140°F (60°C) |
| Spray Rotation | 360度 |
| 表面クリーナー直径 | 15インチ |
| Extension Wand Length | 16インチ |
| 接続タイプ | 1/4 inch Quick-Connect |
| アイテム重量 | 4.66ポンド |
| メーカー | フォティング |
| モデル番号 | KLC-CP |
設定
Follow these steps to properly set up your FOTING Surface Cleaner Attachment:
- コンポーネントの検査: Before assembly, ensure all parts listed in the 'Package Contents' section are present and free from damage.
- 延長ワンドを接続する: Attach the 16-inch extension wand to your pressure washer gun. The wand features a 1/4-inch quick-connect fitting. Push the collar back on your pressure washer gun's quick-connect, insert the wand, and release the collar to secure it. Pull on the wand to confirm a secure connection.
- 表面クリーナーを取り付けます: Connect the FOTING 15-inch Surface Cleaner to the other end of the extension wand. Use the same quick-connect method: pull back the collar on the wand, insert the surface cleaner's connector, and release the collar. Verify the connection is secure.
- ノズルを確認してください: Ensure the two spray nozzles located on the underside of the surface cleaner are securely tightened. These are pre-installed but should be checked.
- 給水： Connect your pressure washer to a suitable water supply according to its manufacturer's instructions.
Figure 3: Surface Cleaner connected to a pressure washer.
手術
The FOTING Surface Cleaner is designed for efficient cleaning of large flat surfaces. Follow these steps for optimal performance:
- 準備エリア: 掃除するエリアから散らかったゴミ、家具、障害物を取り除いてください。
- 高圧洗浄機を起動します: Turn on your water supply and start your pressure washer according to its operating instructions.
- クリーニングの開始: Position the surface cleaner flat on the surface you intend to clean. Hold the pressure washer gun firmly with both hands.
- トリガーを作動: Squeeze the trigger on your pressure washer gun. The high-pressure water will activate the internal spray bar, causing it to rotate 360 degrees and clean a 15-inch wide path. The integrated splash-proof skirt will help minimize overspray.
- 着実に動く： Move the surface cleaner slowly and consistently across the surface. Overlap each pass slightly to ensure thorough and even cleaning, preventing streaks. Avoid lifting the cleaner off the surface during operation.
- リリーストリガー: Release the trigger to stop the water flow when you need to pause, reposition, or finish cleaning.
- Rinse Surface: After cleaning with the surface cleaner, it is often beneficial to rinse the entire area with a standard pressure washer nozzle to wash away loosened dirt and debris.
- シャットダウン: Follow your pressure washer's instructions for proper shutdown, including releasing 残圧。
Figure 4: High Performance Features - 360° Spray Rotation and Splash-Free Skirt.
Figure 5: Multi-Application - Effective on various hard surfaces.
メンテナンス
Regular maintenance ensures the longevity and optimal performance of your FOTING Surface Cleaner Attachment.
- ノズルのクリーニング: If you notice reduced pressure or an inconsistent spray pattern, the nozzles may be partially clogged. Disconnect the surface cleaner from the pressure washer. Use the provided cleaning needle to carefully clear any debris from the nozzle openings. Rinse the nozzles with clean water.
- O-Ring Inspection and Replacement: Periodically inspect the O-rings on all quick-connect fittings for signs of wear, cracks, or damage. Worn O-rings can cause leaks. Replace damaged O-rings with the included spare O-rings to maintain a watertight seal.
- 一般的な清掃: After each use, rinse the entire surface cleaner thoroughly with clean water to remove any dirt, grime, or chemical residues. This prevents buildup and corrosion.
- ストレージ： Store the surface cleaner in a clean, dry, and protected area. Avoid storing it in direct sunlight or in locations where temperatures can drop below freezing, as this can damage components.
トラブルシューティング
| 問題 | 考えられる原因 | 解決 |
|---|---|---|
| Reduced Pressure / Uneven Spray | Clogged nozzles, insufficient water supply, loose connections. | Clean nozzles with the provided needle. Ensure adequate water flow to the pressure washer. Check all quick-connect fittings for secure attachment. |
| 接続部の漏れ | Loose connections, worn or damaged O-rings. | Ensure all quick-connect fittings are fully engaged. Inspect O-rings and replace if damaged. Use waterproof tape on threaded connections if necessary. |
| Surface Cleaner Not Rotating | Clogged nozzles, insufficient water pressure from pressure washer, obstruction in spray bar. | Clean nozzles. Verify your pressure washer meets the minimum PSI/GPM requirements. Inspect the internal spray bar for any blockages. |
保証とサポート
The FOTING 15-inch Pressure Washer Surface Cleaner Attachment is backed by a THREE-YEAR after-sale service.
If you encounter any problems or have questions regarding the product, please contact FOTING customer support. Refer to your purchase documentation or the FOTING official web連絡先情報のサイト。