1. はじめに
This instruction manual provides essential information for the safe and efficient operation, installation, and maintenance of your FOTING 1.5HP Shallow Well Pump with Pressure Tank, Model JGP110037C. Please read this manual thoroughly before using the pump to ensure proper function and to prevent injury or damage. Keep this manual for future reference.
Figure 1: FOTING 1.5HP Shallow Well Pump with Pressure Tank
2. 安全情報
火災、感電、および人的傷害のリスクを軽減するために、常に基本的な安全上の注意事項を守ってください。
- 電気安全: Ensure the pump is connected to a properly grounded 115V, 60Hz power supply. Do not operate with damaged cords or plugs. Avoid using extension cords if possible; if necessary, use a heavy-duty outdoor-rated cord.
- 水の安全性： Do not pump flammable or corrosive liquids. Ensure the pump is not operated dry (without water), as this can cause severe damage.
- 個人の安全: Wear appropriate personal protective equipment (PPE) such as safety glasses and gloves during installation and maintenance. Keep children and unauthorized persons away from the operating pump.
- インストール: Install the pump in a well-ventilated area, protected from direct sunlight and freezing temperatures. Ensure all connections are secure and leak-free.
- メンテナンス： メンテナンスやサービスを実行する前に電源を切ってください。
3.製品オーバーview
The FOTING 1.5HP Shallow Well Pump with Pressure Tank is designed for efficient water boosting and irrigation applications. It features a powerful motor, a durable pressure tank, and automatic operation capabilities.
主な特徴:
- 強力なモーター: 1.5HP motor with a maximum flow rate of 1340 GPH and a maximum lift of 164 feet.
- High Suction Capability: Capable of suctioning water from depths up to 23 feet.
- Integrated Pressure Tank: 5-gallon pressure tank with a pre-set pressure range for automatic operation.
- 自動操作: Features a mechanical pressure switch that automatically starts the pump at 1.5 bar and shuts it off at 3 bar.
- 耐久性のある構造: Reinforced thermoplastic structure and a finely finished iron tank for corrosion and wear resistance.
- 安全機能: Equipped with overheat protection to prevent motor burnout and a durable carbon ceramic mechanical seal to prevent water leakage.
- 多彩な接続: 1" NPT outlet and inlet, includes 2 adapters for NPT 1" to GHT 3/4" connections.
図2：詳細 view of pump components including 1" NPT Outlet, 1" NPT Intake, Start Waterproof Cover, 5-Gal Pressure Tank, High Pressure Soft Tube, Pressure Gauge, Mechanical Pressure Switch, and Stable Base.
Figure 3: Key performance specifications and protection features.
Figure 4: Details of the pressure gauge, mechanical pressure switch, and thermal overload protection.
4. セットアップとインストール
4.1 開梱
Carefully remove all components from the packaging. Inspect for any damage that may have occurred during shipping. Ensure all parts listed in the packing list are present.
4.2 場所
Place the pump on a stable, level surface. The location should be protected from moisture, direct sunlight, and freezing temperatures. Ensure adequate ventilation around the motor.
4.3配管接続
- Connect the suction line to the 1" NPT intake port of the pump. Ensure a tight, leak-free connection.
- Connect the discharge line to the 1" NPT outlet port. Use the provided NPT 1" to GHT 3/4" adapters if connecting to a standard garden hose.
- It is recommended to install a check valve on the suction line to prevent water from flowing back into the well or source, especially for self-priming applications.
- Ensure all pipes and fittings are compatible with the intended water pressure and temperature.
Figure 5: Connection options for water taps and self-priming setups.
4.4 ポンプの呼び水
Before first use, the pump must be primed.
- Locate the priming plug on the top of the pump housing.
- Remove the priming plug and slowly fill the pump casing with water until it overflows.
- プライミングプラグを確実に取り付けてください。
- Ensure the suction line is fully submerged in the water source.
4.5 電気接続
Connect the pump to a standard 115V, 60Hz grounded electrical outlet. Ensure the power switch on the pump is in the "OFF" position before plugging it in.
5. 操作手順
5.1 ポンプの始動
- ポンプが適切にプライミングされていることを確認します（セクション 4.4 を参照）。
- Turn the power switch to the "ON" position. The pump will start to draw water.
- Observe the pressure gauge. The pump's mechanical pressure switch is set to automatically start when pressure drops below 1.5 bar and shut off when it reaches 3 bar. The maximum pressure the tank can hold is 4.5 bar.
- Allow the pump to run until a steady flow of water is achieved and the pressure stabilizes.
5.2 アプリケーション
このポンプは、次のようなさまざまな用途に適しています。
- Garden and lawn irrigation.
- Agricultural structures and small farms.
- Domestic water supply for homes and cabins.
- Pipe pressurization and water transfer.
Figure 6: Pump in use for garden irrigation.
Figure 7: Versatile applications of the FOTING pump.
6. メンテナンス
Regular maintenance ensures the longevity and optimal performance of your FOTING pump. Always disconnect power before performing any maintenance.
6.1一般的なクリーニング
- Keep the pump exterior clean and free from debris.
- 過熱を防ぐため、通気口がふさがれていないことを確認してください。
6.2 冬季対策（寒冷地向け）
ポンプが凍結温度にさらされる場合は、損傷を防ぐためにポンプ内の水を抜く必要があります。
- ポンプを電源から外します。
- ポンプからすべての水を排出します。asing and pressure tank by opening drain plugs and disconnecting pipes.
- Store the pump in a warm, dry place during winter months.
6.3メカニカルシール
The pump is equipped with a durable carbon ceramic mechanical seal designed to prevent water leakage and extend service life. If leakage occurs around the shaft, inspect the seal for wear or damage and replace if necessary.
7。 トラブルシューティング
Refer to the table below for common issues and their solutions. If the problem persists, contact FOTING customer service.
| 問題 | 考えられる原因 | 解決 |
|---|---|---|
| ポンプが始動しない。 | No power; tripped circuit breaker; faulty switch; motor overload. | Check power connection; reset breaker; inspect switch; allow motor to cool if overheat protection activated. |
| ポンプは作動しますが、水が出ないか流量が低下します。 | Pump not primed; air leak in suction line; clogged intake; low water source. | Re-prime the pump; check suction line for leaks; clear intake; ensure adequate water source. |
| ポンプが頻繁にオンとオフを繰り返します。 | Air in pressure tank; pressure switch malfunction; small leak in system; no check valve on suction line. | Check air charge in tank; inspect pressure switch; check for leaks in plumbing; install a check valve on the suction line if not present. |
| ポンプがうるさいです。 | Cavitation (air in water); worn bearings; foreign object in impeller. | Ensure pump is fully primed and suction line is sealed; inspect impeller for obstructions; contact service if bearings are suspected. |
| 水漏れ。 | Loose connections; damaged mechanical seal; cracked housing. | Tighten all connections; inspect and replace mechanical seal if damaged; contact service for housing damage. |
8. 仕様
| 属性 | 価値 |
|---|---|
| ブランド | フォティング |
| モデル番号 | JGP110037C |
| 力 | 1.5馬力 |
| 巻tage | 115ボルト |
| 頻度 | 60Hz |
| 最大流量 | 1340GPH |
| Max Lift (Head) | 164フィート |
| 最大吸引力 | 23フィート |
| 圧力タンク容量 | 5ガロン |
| Automatic Pressure Switch On | <1.5バール |
| Automatic Pressure Switch Off | > 3.0 バール |
| Max Pressure (Tank) | 4.5バール |
| インレット/アウトレットサイズ | 1インチNPT |
| 材料 | プラスチック、金属 |
| 製品寸法（長さ x 幅 x 高さ） | 17インチ x 10.5インチ x 20インチ |
| アイテム重量 | 33.7ポンド |
| 保護タイプ | IPX4 |
| 最高流体温度 | 95°F |
Figure 8: Pump working performance chart.
9. 保証と顧客サポート
FOTING is committed to providing high-quality products and excellent customer service.
9.1 保証情報
Specific warranty details may vary. Please refer to the product packaging or contact FOTING customer service for comprehensive warranty information regarding your 1.5HP Shallow Well Pump with Pressure Tank.
9.2 カスタマーサポート
For technical support, troubleshooting assistance, or any inquiries regarding your FOTING product, please contact our customer service team. Our professionals are available to provide support and ensure your water system remains stable.
You can find contact information on the official FOTING webサイトまたは購入プラットフォームを通じて購入できます。