FOTING In/Above Ground Pool Pump Instruction Manual

1.製品オーバーview

The FOTING In/Above Ground Pool Pump is a self-priming, dual-speed pump designed for efficient water circulation in various swimming pools. Equipped with a robust 2HP copper wire motor, it offers a flow rate of up to 3170 GPH (low speed) and 7000 GPH (high speed), with a maximum head lift of 69 feet. This pump features thermal overload protection for enhanced safety and longevity, and includes a removable filter basket and drain plug for easy maintenance. It is suitable for both above-ground and in-ground pool applications, as well as water parks, bathing pools, hot tubs, spas, and irrigation systems.

Figure 1: FOTING In/Above Ground Pool Pump with included 1.5" and 2" NPT inlet connectors and waterproof tape.

2. 安全情報

設置および操作の前に、すべての安全に関する指示をよく読んで理解してください。これらの指示に従わないと、感電、火災、または重傷を負う可能性があります。

• サービスやメンテナンスを行う前に、必ずポンプの電源を切ってください。
• 電源がポンプの容量と一致していることを確認するtag要件 (230V)。
• The pump must be installed by a qualified electrician in accordance with all local and national electrical codes.
• 電源コードが損傷している場合はポンプを操作しないでください。
• ポンプの動作中は、子供や関係者以外の人をポンプのそばに近づけないでください。
• The pump is equipped with thermal overload protection. If the pump stops unexpectedly, allow it to cool down before attempting to restart. Investigate potential causes such as clogs or insufficient water flow.

3. セットアップとインストール

Proper installation is crucial for the pump's performance and longevity. The pump is self-priming, but proper plumbing connections are essential.

3.1 開梱と検査

• パッケージからすべてのコンポーネントを慎重に取り出します。
• Verify that all parts are present: pump unit, two 1.5" NPT inlet adapters, two 2" NPT inlet adapters, and waterproof tape.
• Inspect the pump for any visible damage that may have occurred during shipping. Do not install if damaged.

3.2 配置

• Place the pump on a solid, level surface near the pool.
• モーターの周囲に十分な換気を確保してください。
• Position the pump to minimize the length of suction and discharge piping.

3.3配管接続

The FOTING pump supports two methods for water pipe connection using the included 1.5" and 2" NPT inlet adapters.

Figure 2: Two methods for connecting water pipes to the pump, utilizing 1.5-inch and 2-inch PVC pipe adapters.

• Method 1: Direct PVC Pipe Connection
  Connect 1.5" or 2" PVC pipes directly to the pump's inlet and outlet ports using the appropriate adapters and waterproof tape for a secure, leak-free seal.
• Method 2: Flexible Hose Connection
  Utilize the provided adapters to connect flexible hoses (1.5" or 2") to the pump. Ensure hose clamps are used for a tight connection.
• 空気の漏れはポンプのプライミングと効率に影響を及ぼす可能性があるため、すべての接続が適切に密閉されていることを確認してください。

3.4 電気接続

This pump operates on 230V. A power cord is not included and must be wired by a qualified electrician according to local electrical codes.

• Ensure the power supply is off before making any electrical connections.
• 適切な過電流保護を備えた専用回路にポンプを接続します。
• 正しいボリュームを確認するtageと amperageの評価。

4. 操作

The FOTING pool pump features dual-speed operation, allowing you to optimize performance and energy consumption.

4.1 ポンプの呼び水

• Before initial startup, ensure the pump is filled with water through the skimmer or by removing the transparent lid and filling the filter basket housing.
• Close all drain valves and ensure the pool water level is above the skimmer.
• Once filled, replace the lid securely. The pump's self-priming capability will then quickly establish water flow.

4.2 Dual Speed Control

The pump offers two operating speeds: High and Low. A switch located at the bottom of the motor allows you to select the desired speed.

Figure 3: High Speed mode provides 7000 GPH for rapid water circulation and daytime use.

• High Speed (7000 GPH): Ideal for faster filtration, cycling the entire pool volume quickly, and during periods of heavy use or when cleaning the pool.

Figure 4: Low Speed mode provides 3170 GPH for energy saving and quieter operation during off-peak hours.

• Low Speed (3170 GPH): Recommended for energy saving, quieter operation, and maintaining filtration during less active periods or overnight.

Adjust the speed based on your pool's size, filtration requirements, and desired energy consumption.

5. メンテナンス

Regular maintenance ensures optimal performance and extends the lifespan of your FOTING pool pump.

5.1 フィルターバスケットの清掃

The pump is equipped with a removable filter basket to capture debris. The transparent lid allows for easy visual inspection.

Figure 5: The extra-large filter basket effectively collects leaves, twigs, and gravel, and is easily removable for cleaning.

• ポンプをオフにして電源を外します。
• Unscrew the transparent lid counter-clockwise.
• フィルターバスケットを取り外し、集めたゴミを空にします。
• バスケットを水でよくすすいでください。
• Inspect the O-ring on the lid for cracks or wear; replace if necessary.
• Place the clean basket back into the pump and securely fasten the lid.

5.2 ポンプの排水

The integrated drain plug allows for easy water drainage, particularly useful for winterization or extended periods of non-use.

図6：以上view of pump features including the drain plug for easy water removal and the transparent cover for filter basket visibility.

• ポンプをオフにして電源を外します。
• ポンプハウジングの底部にある排水プラグを見つけます。
• 排水プラグを緩めて、ポンプから水が排出されるようにしてください。
• 排水後はプラグをしっかりと閉めてください。

6。 トラブルシューティング

This section provides solutions to common issues you may encounter with your FOTING pool pump.

7. 仕様

Detailed technical specifications for the FOTING In/Above Ground Pool Pump.

Figure 7: Performance curve illustrating the relationship between head lift and flow rate for both high and low speeds.

8. 保証とサポート

FOTING provides a THREE-YEAR after-sale service for this product.

If you encounter any problems or have questions regarding your FOTING pool pump, please contact our customer support team for assistance. Refer to your purchase documentation for specific contact details or visit the official FOTING webサイト。