BUNN BUNVPS Pour-O-Matic Three-Burner Pour-Over Coffee Brewer Instruction Manual

導入

This manual provides detailed instructions for the safe and efficient operation, maintenance, and troubleshooting of your BUNN BUNVPS Pour-O-Matic Three-Burner Pour-Over Coffee Brewer. Please read all instructions carefully before using the appliance to ensure proper function and to prevent injury or damage.

Image: The BUNN BUNVPS Pour-O-Matic Three-Burner Pour-Over Coffee Brewer, featuring its three warming plates and brew funnel area.

重要な安全情報

Always follow basic safety precautions when using electrical appliances to reduce the risk of fire, electric shock, and injury to persons. This appliance is for commercial use only. Do not immerse the brewer in water or other liquids. Do not operate with a damaged cord or plug. Keep hands and cords away from hot surfaces.

• 醸造機が安定した水平な面に設置されていることを確認してください。
• 適切に接地されたコンセントにのみ接続してください。
• Do not operate the brewer without water in the tank.
• 熱い液体や表面を取り扱うときは注意してください。
• Unplug the brewer before cleaning or servicing.

設定

1. 開梱と設置

1. Carefully remove the brewer from its packaging. Retain packaging for future transport if needed.
2. Place the brewer on a sturdy, level counter or table. Ensure there is adequate clearance around the unit for ventilation.
3. Do not place the brewer near heat sources or in direct sunlight.

2. 初期洗浄

1. Wash the brew funnel, glass carafes, and sprayhead in warm, soapy water. Rinse thoroughly.
2. 醸造機の外側を広告で拭くamp 布で拭いてください。研磨剤入りの洗剤は使用しないでください。

3. 水タンクに水を入れる

1. Ensure the brewer is unplugged.
2. Open the lid at the top of the brewer.
3. Pour cold, fresh water into the opening until it reaches the fill line or the tank is full. Do not overfill.
4. 蓋をしっかりと閉めてください。

4. 電源接続

1. ブリューワーをアース付き電源コンセントに差し込みます。
2. Allow approximately 15-20 minutes for the water to heat to the optimal brewing temperature. The "Ready" light will illuminate when the water is heated.

操作手順

コーヒーを淹れる

1. Ensure the brewer is plugged in and the "Ready" light is illuminated.
2. Place a clean BUNN filter into the brew funnel.
3. Add the desired amount of fresh, medium-ground coffee into the filter. Refer to the coffee manufacturer's recommendations for optimal strength.
4. Slide the brew funnel into the funnel rails beneath the sprayhead.
5. Place an empty glass carafe on the warming plate directly below the brew funnel.
6. Pour a full carafe of cold, fresh water into the top opening of the brewer. This action initiates the brewing cycle.
7. The brewing process will begin immediately. Hot coffee will dispense into the carafe.
8. Once brewing is complete, carefully remove the carafe. The warming plate will keep the coffee hot.
9. Remove the brew funnel, discard the used coffee grounds and filter, and rinse the funnel.

Using the Warming Plates

The BUNN BUNVPS features three warming plates to keep brewed coffee at an ideal serving temperature. Each warming plate is controlled by an individual switch, typically located on the front panel. Turn on the switch for the desired warming plate after placing a carafe of brewed coffee on it. Turn off the switch when the warming plate is not in use or when the carafe is empty.

メンテナンス

Regular cleaning and maintenance will ensure the longevity and optimal performance of your coffee brewer.

毎日の清掃

• Carafes and Brew Funnel: After each use, wash carafes and the brew funnel with warm, soapy water. Rinse thoroughly and allow to air dry.
• 外観： 醸造機の外側の表面を広告で拭きますamp cloth. Do not use abrasive pads or harsh chemicals.

Periodic Descaling (Monthly or as needed)

Mineral deposits from water can build up inside the brewer, affecting performance. Descaling is recommended regularly.

1. Unplug the brewer and allow it to cool completely.
2. Remove the sprayhead by twisting it counter-clockwise. Clean any visible mineral deposits from the sprayhead holes using a small brush or paperclip.
3. Prepare a descaling solution according to the descaler product instructions (e.g., white vinegar and water).
4. カルキ除去液を水タンクに注ぎます。
5. 空のカラフェを保温プレートの上に置きます。
6. Plug in the brewer and allow it to heat.
7. Initiate a brew cycle by pouring a carafe of water into the top. Repeat this process until the entire descaling solution has passed through the brewer.
8. Run several cycles of fresh, clean water through the brewer to rinse thoroughly before brewing coffee again.
9. Reattach the sprayhead.

Note: Do not use harsh chemicals or abrasive materials for descaling, as they can damage the internal components.

トラブルシューティング

ここに記載されていない問題が発生した場合、または解決策を実行しても問題が解決しない場合は、カスタマー サポートにお問い合わせください。

仕様

保証情報

This BUNN BUNVPS Pour-O-Matic Three-Burner Pour-Over Coffee Brewer is covered by a manufacturer's warranty. Specific warranty terms, conditions, and duration may vary. Please refer to the warranty card included with your product or visit the official Bunn website for detailed information regarding your warranty coverage and how to make a claim.

Note: Retain your proof of purchase for warranty validation.

カスタマーサポート

For technical assistance, replacement parts, or further inquiries regarding your BUNN BUNVPS coffee brewer, please contact Bunn customer support. Contact information can typically be found on the manufacturer's webサイトまたは製品パッケージに記載されています。

When contacting support, please have your model number (BUNVPS) and serial number (if applicable) ready for faster service.