iWFCam X3 Mini Camera User Manual

iWFCam X3 Mini Camera

Specifications

• Power Supply: 5V/1A USB
• Network Connection: Supports AP mode and IP mode
• WiFi Support: 2.4GHz, letters, and numbers only
• Default Camera Password: 8888

Download the software “iwFCam

• For Apple mobile phones, please enter the APP Store and search for the APP with the name “iwFCam” to install, for Android mobile phones, please scan the QR code below with your mobile phone browser.
• Select “Direct Download Android Apk Installation” to download and install the software.

• Make sure that the distance between the mobile phone and the camera does not exceed 10 metres.

Products

• Switch on: Long press (OFF) switch on/off button for about 2 seconds, the red light is always on and the blue light is flashing slowly.
• Switch off: Long press (OFF) ON/OFF button for about 2 seconds.
• Reset Button:Under the power on state, use the reset pin to insert into the RESET hole on the top, the camera will automatically reset and reboot to the initial state after 3 seconds.
• TF card holder: Insert the memory card to save the recording files Charging: Access to 5V/1A USB power supply charging, charging orange indicator light is always on, full of orange, indicator light off

The indicator light shows the description:

1. No network connection [AP mode]: red light is always on, blue light flashes slowly
2. Remote mode [IP mode] is connected to WiFi network: red light is always on, blue light is always on.
3. Remote Mode [IP Mode] not connected to the network: indicator light fast flash
4. Indicator light can be turned on/off on APP

No network connection

1. Long press (OFF) the on/off button for about 3 seconds, the camcorder enters standby mode.
2. Open the settings (Figure 1) into the WLAN settings page of your mobile phone to find the Wif signal with the name BK*** (Figure 2) and connect (that is, switch the WiFi connected to your mobile phone to the WiFi signal of the camera) (Figure 3)
3. WLAN settings page will pop up “current WLAN I not available, whether to continue to use this WLAN?’ click Use (Figure 4)
4. In the upper left corner of the WLAN settings
   page, click to return to the main page of the mobile phone (Figure 5)

The following pictures can be referred to

1. 0pen the previously installed APP(iWFCam)(Figure 6), make sure the phone and the camera’s WiFi stay connected, after connecting the camera’s WiFi, please be patient and wait for the pop-up window, or you can manually search(Figure 7), add the camera (Figure 8) and show it online, or you can manually refresh it(Figure 9) after the main page of the APP will pop-up(Figure 10) click to cancel, (Figure 11) click to Skip, at this time, tap in to directly watch the screen in real-time and make some settings for the camera (Figure 12).

The following pictures can be referred to

Remote connection settings

1. When the APP camera shows online (Figure 13), click the Settings button in the lower right corner of the camera view in the APP (Figure 14) to enter the Adwanced Settings (Figure 15), go to WiFi in the Adwanced Settings, Connections and Configurations WiFi (Figure 16), select the WiFi in use in your own home and enter the correct WiFi password (Figure 17), and then click Confirm.

The following pictures can be referred to

1. Wait for the camera to update and reboot the device (Figure 18: 1) Click to return to the APP main page (Figure 18: 2) When the camera shows online again, it means that it has been successfully set up in remote mode (Figure 19) You will be able to open your mobile phone to monitor anytime and anywhere (Figure 20)

Note:

1. Please make sure the distance between the camera and the router is not more than 10 metres when connecting.
2. Only 2.4G WiFi is supported and the name and password are composed of letters or numbers, WiFi names and passwords containing Chinese and special symbols are not supported.

Encrypting the camera

• In the APP, you can add a password for the camera, the default password of the camera is: 8888, if you change the password and forget the password, you can reset the camera and restore it to the default password 8888.

Troubleshooting

1. If you change the network environment to use it, please reset the camera first and then reconfigure the Wifi.
2. If the camera does not recognise the memory card please replace the memory card or format it before use.
3. Before switching off the camera, please stop the recording on the app, so as not to lose and damage the last video file without saving it.
4. The camera will have a certain amount of heat in the work, but does not affect the performance can rest assured that the use.
5. If it shows wrong access password: please reset the camera to restore to the default password 8888.
6. Please access to 5V/1A USB charger charging, do not access the voltage greater than 5V power charging.

Warning:

• changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including Interference that may cause undesired operation.

Note:

• This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection akathat a miat interterence in a icsoch dal installation. this equipment generates, uses, and can radiate radio frequency energy. and if not installed and used in accordance with the instrictions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
• Installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
  • Keonent or relocale the recevis anterma.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

FAQs

Q: What should I do if the camera does not recognize the memory card?
A: Try replacing the memory card or format it before use.

Q: Can I use a power source greater than 5V for charging?
A: No, only use a 5V/1A USB charger for charging to avoid damage.