Prodotto finitoview
The BISSELL CrossWave 17132 is a versatile 3-in-1 multi-surface floor cleaner designed to vacuum, wash, and dry hard floors, carpets, and rugs simultaneously. This integrated cleaning system offers an efficient alternative to traditional vacuuming and mopping, providing thorough cleaning with less effort. Its dual tank technology ensures that clean water and formula are always separate from dirty water, guaranteeing a fresh clean every time.
Componenti inclusi
Before beginning assembly, ensure all components are present in the packaging:
- BISSELL CrossWave 17132 Unit (Main Body and Handle)
- Multi-Surface Cleaning Formula (Detergent)
- Multi-Surface Brush Roll (Replacement Brush)
- Storage and Cleaning Tray (Station)
Image: The BISSELL CrossWave 17132 unit shown with its accompanying multi-surface cleaning formula, an extra brush roll, and the storage and cleaning tray.
Istruzioni di installazione
Assemblea
- Inserire la maniglia nel corpo principale dell'unità finché non scatta saldamente in posizione.
- Ensure the clean water tank is properly seated on the back of the unit.
- Ensure the dirty water tank is properly seated on the front of the unit.
Riempimento del serbatoio dell'acqua pulita
- Rimuovere il serbatoio dell'acqua pulita dal retro della macchina.
- Svitare il tappo sul fondo del serbatoio.
- Fill the tank with warm tap water up to the 'Water' fill line for the desired cleaning area (small or large).
- Add the BISSELL Multi-Surface Cleaning Formula up to the corresponding 'Formula' fill line.
- Replace the cap and reinsert the tank into the machine, ensuring it is securely latched.
Istruzioni per l'uso
Accensione e selezione della modalità
- Collegare il cavo di alimentazione a una presa elettrica dotata di messa a terra.
- Press the power button located on the handle to turn on the machine.
- Use the fingertip controls on the handle to select the appropriate cleaning mode: Pavimento duro or Area Rug.
Processo di pulizia
To dispense cleaning solution, hold down the spray trigger located on the handle. Release the trigger to stop dispensing.
For best results, make a wet pass by holding the spray trigger and moving the machine slowly forward and backward. Then, make a dry pass by releasing the trigger and moving the machine over the same area to suction up the dirty solution.
Image: A user operating the BISSELL CrossWave 17132 on a hard floor, demonstrating its cleaning action on a liquid spill.
Image: The BISSELL CrossWave 17132 cleaning a tiled floor, effectively picking up scattered dry debris and wet messes.
Manutenzione e cura
Svuotamento e pulizia del serbatoio dell'acqua sporca
- Spegnere e scollegare la macchina.
- Remove the dirty water tank from the front of the machine.
- Carefully remove the filter and pour out the dirty water.
- Rinse the tank and filter thoroughly with water. Allow the filter to air dry completely before reinserting.
- Replace the filter and reattach the dirty water tank to the machine, ensuring it is securely latched.
Cleaning the Brush Roll and Brush Roll Window
- Spegnere e scollegare la macchina.
- Rimuovere la finestra del rullo spazzola tirando verso l'alto la linguetta.
- Remove the brush roll by grasping the tab and pulling it out.
- Rinse the brush roll and brush roll window under running water. Remove any hair or debris.
- Allow both to air dry completely before reassembling.
- Reinsert the brush roll, ensuring it clicks into place, then reattach the brush roll window.
Immagine: un primo piano view of the BISSELL CrossWave 17132's brush roll and base, highlighting the multi-surface brush for effective cleaning.
Using the Storage and Cleaning Tray
After each use, place the CrossWave on the storage and cleaning tray. Fill the tray with water up to the indicated line. Run the machine for approximately 10-20 seconds to rinse the brush roll and internal components. This helps prevent odors and maintains performance.
Risoluzione dei problemi
Machine Not Dispensing Solution
- Check if the clean water tank is properly filled and seated.
- Ensure the spray trigger is being held down during operation.
- Verify that the formula cap is securely tightened.
Scarsa aspirazione
- Controllare se il serbatoio dell'acqua sporca è pieno e deve essere svuotato.
- Ensure the dirty water tank is properly seated and sealed.
- Inspect the brush roll and brush roll window for clogs or debris.
- Clean the filter and ensure it is dry before reinstallation.
La macchina non si accende
- Verificare che il cavo di alimentazione sia collegato saldamente a una presa elettrica funzionante.
- Verificare la presenza di eventuali interruttori automatici scattati.
Specifiche del prodotto
| Caratteristica | Dettaglio |
|---|---|
| Marca | BISSELL |
| Nome del modello | BISSELL Crosswave |
| Numero di modello | 17132 |
| Caratteristica speciale | Sweep, wipe and dry (3-in-1 functionality) |
| Tipo di filtro | Con filtro |
| Capacity (Clean/Dirty Water Tanks) | 0.82 litri |
| Cosatage | 560 Watt |
| Usi consigliati | Pavimenti in moquette, pavimenti in legno, tappezzeria, rimozione peli di animali domestici |
| Fattore di forma | Verticale |
| Colore | Blue/Titanium |
| Livello di rumore | 80 decibel |
| Tipo di controllore | Pannello di controllo integrato |
| Metodo di controllo | Tocco |
| Peso dell'articolo | 5 kg 200 g (11.46 libbre) |
| Dimensioni articolo (LxPxA) | 30 x 23 x 116.8 centimetri |
| Fonte di alimentazione | Elettrico con cavo |
| Voltage | 220V |
| È senza fili? | NO |
Garanzia e supporto
For warranty information, technical support, or to purchase replacement parts and cleaning formulas, please visit the official BISSELL website or contact BISSELL customer service. Always use genuine BISSELL replacement parts and cleaning formulas to ensure optimal performance and to maintain your warranty.
In base ai dati forniti, non erano disponibili video ufficiali del prodotto del venditore da incorporare.
